DOWNLOAD Sharp AR-405 (serv.man10) Service Manual ↓ Size: 924.36 KB | Pages: 85 in PDF or view online for FREE

Model
AR-405 (serv.man10)
Pages
85
Size
924.36 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / AR405 Service Manual-Simulation Codes
File
ar-405-sm10.pdf
Date

Sharp AR-405 (serv.man10) Service Manual ▷ View online

3
3 - 2
Purpose
Operation test/check
Function
(Purpose)
Used to check the operation of sensors and detectors in the sorter and the related circuit.
Section
Sorter/Finisher
Item
Operation
Operation/
Procedure
The display differs depending on the unit (sorter, finisher) installed.
The operations of the sensors and detectors in the sorter and the finisher section are displayed.
The active sensors and detectors are highlighted.
In the case of AR-SS1
PIS
Paper entry port sensor
CHPS
Holder home sensor
PSFT
Paper empty sensor
SHPSW
Stapler home switch
THLS
Upper limit sensor
PSFSU
Stapler paper sensor
TLLS
Lower limit sensor
SSFSU
Stapler empty sensor
THPS
Bin home sensor
SSSW
Joint section door sensor
PSFT0
Take-out position sensor
SCSW
Staple unit section door sensor
SPHPS
Alignment rod home sensor
In the case of AR-FN1
JGHP
Jogger motor home sensor
PFD3
Transport sensor 3
READY
Stapler self priming sensor
PFD4
Transport sensor 4
PSHP
Pusher motor home sensor
T3OD
Tray 3 paper exit sensor
STUHP
Staple unit home sensor
STID
Staple tray paper entry sensor
T2PF
Tray 2 paper full sensor
STPD
Staple paper sensor
STND
Stapler replacement sensor
T1PF
Tray 1 paper full sensor
EVRE
Elevator motor encoder
T3UP
Tray 3 upper limit sensor
OFHP
Offset home sensor
T3DN
Tray 3 lower limit sensor
STHP
Staple home sensor
LSTS
Stapler sensor
INPD
Paper entry sensor
NCTS
Staple cartridge sensor
RVPD
Reverse paper exit sensor
PWD
Power off detection
PGOP
Upper transport PG open/close sensor
DSW1
Copier connection detection
PFD1
Transport sensor 1
DSW2
Top door open/close detection
PFD2
Transport sensor 2
DSW3
Front door open/close detection
Note
AR-405
8 – 9
1/21/1999
3 - 3
Purpose
Operation test/check
Function
(Purpose)
Used to check the operation of the loads in the sorter and the control circuit.
Section
Sorter/Finisher
Item
Operation
Operation/
Procedure
The display differs depending on the unit (sorter, finisher) which is installed.
1. The names of the loads which can be operated are displayed. The selected load is highlighted.
2. Press the [EXECUTE] key, and the selected load is operated.
During the operation of the load, the [EXECUTE] key is highlighted.
If the [EXECUTE] key is pressed when it is highlighted, the operation is interrupted.
In the case of AR-SS1
DTM
Transport motor
DCM
Holder motor
BZ
Buzzer
TMM
Bin shift motor
DSM
Alignment motor
SAM
Stapler drive motor
In the case of AR-FN1
PSM
Pusher motor
OG2SL
Paper exit gate 2 solenoid
JGM
Jogger motor
OG3SL
Paper exit gate 3 solenoid
STUM
Staple unit shift motor
RRSL
Reverse roller pressure release solenoid
FML
Main drive motor low transport speed
SPSL
Short path select solenoid
FMH
Main drive motor high transport speed
STSL
ST paper holding solenoid
RVM
Reverse motor
T12CL
Tray 1 and tray 2 speed reduction clutch
EVM
Elevator motor
PDCL
Paddler clutch
OFM
Offset motor
STOPCL
ST paper exit roller pressure clutch
INGSL
Paper entry gate solenoid
T3SLCL
Tray 3 speed reduction clutch
T3UPSL
Tray 3 upper limit solenoid
STM
Staple motor
OG1SL
Paper exit gate 1 solenoid
T3ORSL
Tray 3 normal speed clutch
Note
AR-405
1/21/1999
8 – 10
3 - 6
Purpose
Adjustment
Function
(Purpose)
Used to adjust the finisher stacking capability. (Used to adjust the stop position of the finishser paper width
direction alignment plate (jogger). This adjustment is made by changing the width direction alignment plate home
position by the software.) 
(Target model:AR-S330/280/285/335)
Section
Sorter/Finisher
Item
Operation
Operation/
Procedure
1. Select B mode with [
] and [
] keys.
2. Select the paper size by entering the numbers (0 or 1) with the 10-key pad.
3. Select A mode with [
] and [
] keys.
4. Enter the adjustment value with the 10-key pad.
5. Press the [EXECUTE] key.
The value entered in procedure 4 is set.
The finisher’s jogger starts operation. During operation, the [EXECUTE] key is highlighted.
If the [EXECUTE] key is pressed while it is highlighted, the load operation is interrupted.
Note
4
4 - 2
Purpose
Operation test/check
Function
(Purpose)
Used to check the operation of sensors and detectors in the paper feed section (desk feed, large capacity tray)
and the related circuit.
Section
Paper transport
Item
Operation
Operation/
Procedure
The operating conditions of the sensors and detectors in the paper feed section are displayed.
The active sensors and detectors are highlighted.
AR-405
8 – 11
1/21/1999
Desk Unit Sensor
LCC Unit Sensor
DDOPSW
Door open sensor 
LRE
Remaining quantity sensor 
DPOD1
Paper exit transport sensor 1cs 
LUD
Upper limit sensor 
DPOD2
Paper exit transport sensor 2 cs 
LDD
Lower limit sensor 
DPOD3
Paper transport sensor 3cs 
LPED
Paper empty sensor 
DLUD1
1cs Lift upper limit sensor 
LPFD
Paper exit sensor 
DPED1
1cs Paper empty sensor 
LDSW
Door open SW 
DCSPD1
1cs remaining quantity detection 1
LTOD
Body connection sensor 
DLUD2
2xs lift upper limit sensor 
LCD
Cassette detection line 
DPED2
2cs paper empty sensor 
LLSW
Upper limit switch.
DCSPD2
2cs remaining quantity detection 1
DLUD3
3cs lift upper limit sensor 
DPED3
3cs paper empty sensor 
DCSPD3
3cs remaining quantity detection 1
FOUND1
1cs lift unit detection (Installation detection)
FOUND2
2cs lift unit detection (Installation detection)
FOUND3
3cs lift unit detection (Installation detection)
DCSS11
1cs size detection 0
DCSS12
1cs size detection 1
DCSS13
1cs size detection 2
DCSS14
1cs size detection 3
DCSS21
2cs size detection 0
DCSS22
2cs size detection 1
DCSS23
2cs size detection 2
DCSS24
2cs size detection 3
DCSS31
3cs size detection 0
DCSS32
3cs size detection 1
DCSS33
3cs size detection 2
DCSS34
3cs size detection 3
Note
4 - 3
Purpose
Operation test/check
Function
(Purpose)
Used to check the operation of the loads in the paper feed section (desk paper feed, large capacity tray) and the
control circuits.
Section
Paper transport
Item
Operation
Operation/
Procedure
1. The names of the loads which can be operated are displayed.
Select the load to be checked with the key, and the selected load is highlighted.
2. Press the [EXECUTE] key.
The load selected in procedure 1 starts the operation.
During the operation of the load, the [EXECUTE] key is highlighted. If the [EXECUTE] key is pressed while it is
highlighted, the operation is stopped.
AR-405
1/21/1999
8 – 12
Page of 85
Display

Click on the first or last page to see other AR-405 (serv.man10) service manuals if exist.