Sharp AR-405 (serv.man10) Service Manual ▷ View online
2
2 - 1
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the RADF unit and its control circuit.
Section
ADF/RADF/UDH/SPF
Item
Operation
Operation/
Procedure
Procedure
1. Select the aging mode with the key.
When selection is made, the selected item is highlighted.
[1:SIDE]: Single copy aging mode
[2:SIDE] Duplex copy aging mode
[1:SIDE]: Single copy aging mode
[2:SIDE] Duplex copy aging mode
(Note) [2:SIDE] is displayed only when the unit which allows duplex copy is installed.
2. Select the copy magnification ratio with the key.
(The magnification ratio can be increased or decreased in the increment of 1% with the [ZOOM] key.)
The selected magnification ratio is displayed on the magnification ratio display on the screen.
The magnification ratio can be set only when SPF is installed.
The magnification ratio can be set only when SPF is installed.
3. Press the [EXECUTE] key.
Aging of the document feeder is executed under the conditions specified with procedures 1 and 2.
During aging, the [EXECUTE] key is highlighted. If the [EXECUTE] key is pressed while it is highlighted, the operation
is interrupted.
When two or more operations are selected in procedure 1, "1:SIDE" (single copy aging mode) is unconditionally
performed and the other highlighted displays return to the normal display.
To resume aging, execute with procedure 3.
To change the conditions for aging, execute with procedure 1.
During aging, the [EXECUTE] key is highlighted. If the [EXECUTE] key is pressed while it is highlighted, the operation
is interrupted.
When two or more operations are selected in procedure 1, "1:SIDE" (single copy aging mode) is unconditionally
performed and the other highlighted displays return to the normal display.
To resume aging, execute with procedure 3.
To change the conditions for aging, execute with procedure 1.
*
When the SPF is installed , the magnification ratio can be adjusted in the range of 64% - 200%.
Note
2 - 2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of sensors and detectors in the RADF units and the related circuit.
Section
ADF/RADF/UDH/SPF
Item
Operation
Operation/
Procedure
Procedure
The operations of sensors and detectors in the RADF/ADF/SPFsection are displayed.
The active sensors and detectors are highlighted.
[ADF/RADF installed]
DSS
Empty sensor
Normal display: Document empty
Highlighted: display: Document exist
DFD
Resist sensor
Normal display: Document empty
Highlighted display: Document exist
DTD
Paper timing sensor
Normal display: Document empty
Highlighted display: Document exist
AUOD
DF open/close sensor
Normal display: Close
Highlighted display: Open
TSS1
Tray feed size sensor (large size)
Normal display: Document empty
Highlighted display: Document exist
TSS2
Tray feed size sensor (small size)
Normal display: Document empty
Highlighted display: Document exist
DWS1
Tray width sensor (182mm)
Normal display: OFF
Highlighted display: ON
DWS2
Tray width senso
(210mm/215.9mm)
(210mm/215.9mm)
Normal display: OFF
Highlighted display: ON
DWS3
Tray width sensor (257mm)
Normal display: OFF
Highlighted display: ON
DWS4
Tray width sensor (279.4mm)
Normal display: OFF
Highlighted display: ON
DWS5
Tray width sensor (297mm)
Normal display: OFF
Highlighted display: ON
RDD
Paper exit sensor
Normal display: OFF
Highlighted display: ON
AR-405
8 – 7
1/21/1999
[SPF installed]
DSS empty sensor
Normal display: Document empty
Highlighted display: Document exist
DFD resist sensor
Normal display: Document empty
Highlighted display: Document exist
RDD paper exit sensor
Normal display: Document empty
Highlighted display: Document exist
AUOD DF open/close sensor
Normal display: Close
Highlighted display: Open
TSS1 tray feed size sensor (large size)
Normal display: Document empty
Highlighted display: Document exist
TSS2 tray feed size sensor (small size)
Normal display: Document empty
Highlighted display: Document exist
DWS1 tray width sensor (182mm)
Normal display: OFF
Highlighted display: ON
DWS2 tray width sensor
(210mm/215.9mm)
(210mm/215.9mm)
Normal display: OFF
Highlighted display: ON
DWS3 tray width sensor (257mm)
Normal display: OFF
Highlighted display: ON
DWS4 tray width sensor (279.4mm)
Normal display: OFF
Highlighted display: ON
DWS5 tray width sensor (297mm)
Normal display: OFF
Highlighted display: ON
Note
2 - 3
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the loads in the RADF/ADF/SPF units and the control circuits.
Section
ADF/RADF/UDH/SPF
Item
Operation
Operation/
Procedure
Procedure
1. The names of the loads which can be operated are displayed. Select the load to be checked with the key, and the
selected load is highlighted.
2. Press the [EXECUTE] key.
The load selected in procedure 1 starts the operation. During the operation of the load, the [EXECUTE] key is
highlighted. If the EXECUTE key is pressed while it is highlighted, the operation is stopped.
When two or more operations are selected in procedure 1, the operation is performed in the sequence of display
order.
highlighted. If the EXECUTE key is pressed while it is highlighted, the operation is stopped.
When two or more operations are selected in procedure 1, the operation is performed in the sequence of display
order.
[When ADF/RADF is installed]
DFM
FORWORD Paper feed motor forward rotation
DFM
REVERSE Paper feed motor reverse rotation
DTM
FORWORD Transport motor forward rotation
DTM
REVERSE Transport motor reverse rotation
DRM
Paper expulsion motor
DFSOL
Paper feed solenoid
[When SPF is installed]
DTM
FORWORD Transport motor forward rotation
DTM
REVERSE
Transport motor reverse rotation
STAMP
SOL
Stamp solenoid
Note
AR-405
1/21/1999
8 – 8
3
3 - 2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of sensors and detectors in the sorter and the related circuit.
Section
Sorter/Finisher
Item
Operation
Operation/
Procedure
Procedure
The display differs depending on the unit (sorter, finisher) installed.
The operations of the sensors and detectors in the sorter and the finisher section are displayed.
The active sensors and detectors are highlighted.
The operations of the sensors and detectors in the sorter and the finisher section are displayed.
The active sensors and detectors are highlighted.
In the case of AR-SS1
PIS
Paper entry port sensor
CHPS
Holder home sensor
PSFT
Paper empty sensor
SHPSW
Stapler home switch
THLS
Upper limit sensor
PSFSU
Stapler paper sensor
TLLS
Lower limit sensor
SSFSU
Stapler empty sensor
THPS
Bin home sensor
SSSW
Joint section door sensor
PSFT0
Take-out position sensor
SCSW
Staple unit section door sensor
SPHPS
Alignment rod home sensor
In the case of AR-FN1
JGHP
Jogger motor home sensor
PFD3
Transport sensor 3
READY
Stapler self priming sensor
PFD4
Transport sensor 4
PSHP
Pusher motor home sensor
T3OD
Tray 3 paper exit sensor
STUHP
Staple unit home sensor
STID
Staple tray paper entry sensor
T2PF
Tray 2 paper full sensor
STPD
Staple paper sensor
STND
Stapler replacement sensor
T1PF
Tray 1 paper full sensor
EVRE
Elevator motor encoder
T3UP
Tray 3 upper limit sensor
OFHP
Offset home sensor
T3DN
Tray 3 lower limit sensor
STHP
Staple home sensor
LSTS
Stapler sensor
INPD
Paper entry sensor
NCTS
Staple cartridge sensor
RVPD
Reverse paper exit sensor
PWD
Power off detection
PGOP
Upper transport PG open/close sensor
DSW1
Copier connection detection
PFD1
Transport sensor 1
DSW2
Top door open/close detection
PFD2
Transport sensor 2
DSW3
Front door open/close detection
Note
AR-405
8 – 9
1/21/1999
3 - 3
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the loads in the sorter and the control circuit.
Section
Sorter/Finisher
Item
Operation
Operation/
Procedure
Procedure
The display differs depending on the unit (sorter, finisher) which is installed.
1. The names of the loads which can be operated are displayed. The selected load is highlighted.
2. Press the [EXECUTE] key, and the selected load is operated.
During the operation of the load, the [EXECUTE] key is highlighted.
If the [EXECUTE] key is pressed when it is highlighted, the operation is interrupted.
If the [EXECUTE] key is pressed when it is highlighted, the operation is interrupted.
In the case of AR-SS1
DTM
Transport motor
DCM
Holder motor
BZ
Buzzer
TMM
Bin shift motor
DSM
Alignment motor
SAM
Stapler drive motor
In the case of AR-FN1
PSM
Pusher motor
OG2SL
Paper exit gate 2 solenoid
JGM
Jogger motor
OG3SL
Paper exit gate 3 solenoid
STUM
Staple unit shift motor
RRSL
Reverse roller pressure release solenoid
FML
Main drive motor low transport speed
SPSL
Short path select solenoid
FMH
Main drive motor high transport speed
STSL
ST paper holding solenoid
RVM
Reverse motor
T12CL
Tray 1 and tray 2 speed reduction clutch
EVM
Elevator motor
PDCL
Paddler clutch
OFM
Offset motor
STOPCL
ST paper exit roller pressure clutch
INGSL
Paper entry gate solenoid
T3SLCL
Tray 3 speed reduction clutch
T3UPSL
Tray 3 upper limit solenoid
STM
Staple motor
OG1SL
Paper exit gate 1 solenoid
T3ORSL
Tray 3 normal speed clutch
Note
AR-405
1/21/1999
8 – 10
Click on the first or last page to see other AR-405 (serv.man10) service manuals if exist.