Sharp AR-337 (serv.man8) User Manual / Operation Manual ▷ View online
3-19
CHAPTER
3
7
Check the copy paper selection.
●
When the desired paper size is not selected, touch the desired
paper tray on the touch panel then the AUTO IMAGE key. This
lets the copier automatically set the best reduction or enlargement
ratio and display it on the touch panel, judging from the placed
original size and the desired paper size.
paper tray on the touch panel then the AUTO IMAGE key. This
lets the copier automatically set the best reduction or enlargement
ratio and display it on the touch panel, judging from the placed
original size and the desired paper size.
(See steps 2 and 3 of page 2-11.)
8
Enter the desired number of copies.
9
Press the START (
) key.
●
If the document feeder is used, copying will start after all originals
are scanned.
are scanned.
●
If the document glass is used, proceed to the next step.
10
Replace the finished original with the next original after
the START (
the START (
) key indicator lights up, and then press
the START (
) key. Repeat this step until all originals
have been scanned. Then, press the “READ-END” key
on the touch panel.
on the touch panel.
●
Copying will start at this time.
●
Up to 120 sheets of A4 (8-1/2" x 11") originals or up to 60 sheets
of originals larger than A4 (8-1/2" x 11") can be scanned.
of originals larger than A4 (8-1/2" x 11") can be scanned.
●
If originals of different sizes are used, the copy paper size will be
determined based on the original that is scanned first. If originals
larger than the first original are used, a portion of the images may
not be copied.
determined based on the original that is scanned first. If originals
larger than the first original are used, a portion of the images may
not be copied.
●
You can make a pamphlet by folding the copies in two and
stapling them.
stapling them.
●
To cancel the PAMPHLET COPY function, select the PAMPHLET
COPY function again and press the “CANCEL” key.
COPY function again and press the “CANCEL” key.
PAMPHLET COPY
SPECIAL FUNCTIONS
Pamphlet copy
1
2
3
4
5
6
7
8
9
0
C
P
CLEAR
PROGRAM
AUDIT CLEAR
INTERRUPT
C
CLEAR
INTERRUPT
CA
CLEAR ALL
START
O
URE
PAPER SELECT
COP
AUT
A4
AUTO
EXPOSURE
PAPER SELECT
70%
AUTO IMAGE
READ-END
PLACE NEXT ORIGINAL. PRESS [START].
WHEN FINISHED, PRESS [READ-END].
WHEN FINISHED, PRESS [READ-END].
A4
3-20
CHAPTER
3
SPECIAL FUNCTIONS
Image editing functions
The JOB BUILD function allows copying of multipage documents containing
up to 120 pages (the limit, however, might be up to 60 pages of B4 or A3
(8-1/2" x 14" or 11" x 17") paper size when the copier is equipped with some
option) using the RADF. The original must be divided into sections of up to
50 pages per section. Each section can be fed separately through the
RADF for eventual copying into a complete set(s).
up to 120 pages (the limit, however, might be up to 60 pages of B4 or A3
(8-1/2" x 14" or 11" x 17") paper size when the copier is equipped with some
option) using the RADF. The original must be divided into sections of up to
50 pages per section. Each section can be fed separately through the
RADF for eventual copying into a complete set(s).
●
Once a copy job is set in this mode, the copy mode can not be changed
between the simplex and duplex modes except for INTERRUPT copying.
between the simplex and duplex modes except for INTERRUPT copying.
●
When the JOB BUILD function is selected, the below mentioned functions
can not be selected simultaneously. GROUP MODE/TRANSPARENCY
INSERTS/DUAL PAGE COPY/REPEAT COPY.
can not be selected simultaneously. GROUP MODE/TRANSPARENCY
INSERTS/DUAL PAGE COPY/REPEAT COPY.
●
The JOB BUILD mode has priority over the stream feeding mode.
Stream feeding will not operate while the JOB BUILD mode is selected.
Stream feeding will not operate while the JOB BUILD mode is selected.
The illustration shows an example when copying 120 pages of original.
1
Divide the multipage document (maximum 120 pages)
into sections of 50 pages or less and place the section
containing the first page of the document into the
document feeder tray.
into sections of 50 pages or less and place the section
containing the first page of the document into the
document feeder tray.
2
If a duplex copy mode is required, it must be selected at
this time by pressing the 2-SIDED COPY key.
this time by pressing the 2-SIDED COPY key.
AUTO
b
c
20 sheets
1 page
a
21 page
71 page
50 sheets
Original
50 sheets
IMAGE EDITING FUNCTIONS
The image editing functions include the following functions.
●
Job build: Makes copies from a large volume of originals (up to 120
pages of A4 (8-1/2" x 11") paper size) using the document feeder.
pages of A4 (8-1/2" x 11") paper size) using the document feeder.
●
Centring: Shifts the image to the centre of copy paper when the
original and the copy paper are of different sizes.
original and the copy paper are of different sizes.
●
Repeat copy: Produces repeated copies on a single sheet of copy
paper.
paper.
●
B/W reverse: Reverses the black and white areas.
●
Binding change: Rotates the image of originals for the second side
in the 1-sided to 2-sided copy mode.
in the 1-sided to 2-sided copy mode.
These functions are selected by pressing the “IMAGE EDIT” key on
the SPECIAL MODES screen and pressing the key of each function.
the SPECIAL MODES screen and pressing the key of each function.
JOB BUILD
Divide the original containing more than
50 pages into some sections as shown
above and feed them in the order of c
b
50 pages into some sections as shown
above and feed them in the order of c
b
a. The original should be less than
120 pages in total. If the total page
exceeds 120 (if the above section “a”
exceeds 20 pages), the pages in excess
of the limit will be output to the exit area
without being copied.
exceeds 120 (if the above section “a”
exceeds 20 pages), the pages in excess
of the limit will be output to the exit area
without being copied.
3-21
CHAPTER
3
SPECIAL FUNCTIONS
Image editing functions
IMAGE EDITING FUNCTIONS
READY TO CO
READY TO COPY.
SPECIAL MODES
MARGIN SHIFT
MULTI SHOT
PAMPHLET COPY
ERASE
COVERS
IMAGE EDIT
TEXT STAMP
TRANSPARENCY
INSERTS
DUAL PAGE
COPY
OK
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
AUTO A4
3
Press the SPECIAL MODES key.
●
The SPECIAL MODES screen will appear.
4
Press the “IMAGE EDIT” key.
●
The IMAGE EDIT menu will appear.
5
Press the “JOB BUILD” key.
●
The “JOB BUILD” key will be highlighted.
6
Press the upper “OK” key.
7
Make all other desired copy mode selections and enter
the desired number of copies.
the desired number of copies.
1
2
3
4
5
6
7
8
9
0
C
P
CLEAR
PROGRAM
AUDIT CLEAR
INTERRUPT
T ON FRONT COVER?
NCEL
OK
OK
READY TO COPY.
SPECIAL MODES
IMAGE EDIT
OK
OK
CENTRING
JOB BUILD
REPEAT COPY
BINDING
CHANGE
B/W
REVERSE
READY TO COPY.
SPECIAL MODES
IMAGE EDIT
CENTRING
JOB BUILD
B/W
REVERSE
BINDING
CHANGE
REPEAT COPY
OK
OK
3-22
CHAPTER
3
IMAGE EDITING FUNCTIONS
SPECIAL FUNCTIONS
Image editing functions
When the original and copy paper are of different sizes, CENTRING is
used to shift the image as a whole to the centre of the copy paper.
The image will shift only in the left to right direction, not in the top to
bottom direction.
used to shift the image as a whole to the centre of the copy paper.
The image will shift only in the left to right direction, not in the top to
bottom direction.
●
This function will not work when non-standard size originals or copy
paper are used. This function cannot be selected when enlargement
copying has been selected.
paper are used. This function cannot be selected when enlargement
copying has been selected.
1
Place the originals in the document feeder tray or on the
document glass.
document glass.
CENTRING
8
Press the START (
) key.
●
Scanning of the first section will start.
9
After the first section of original pages has been fed and
the START lights up, remove the scanned originals from
the exit area, set the next section of original pages into
the document feeder tray and press the START (
the START lights up, remove the scanned originals from
the exit area, set the next section of original pages into
the document feeder tray and press the START (
) key.
Repeat this sequence until all sections have been fed.
Then press the “READ-END” key on the touch panel.
Then press the “READ-END” key on the touch panel.
●
Copying will start at this time.
C
CLEAR
INTERRUPT
CA
CLEAR ALL
START
READ-END
PLACE NEXT ORIGINAL. PRESS [START].
WHEN FINISHED, PRESS [READ-END].
WHEN FINISHED, PRESS [READ-END].
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
AUTO A4
Click on the first or last page to see other AR-337 (serv.man8) service manuals if exist.