DOWNLOAD Sharp AR-337 (serv.man8) Service Manual ↓ Size: 4.65 MB | Pages: 127 in PDF or view online for FREE

Model
AR-337 (serv.man8)
Pages
127
Size
4.65 MB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Copying Equipment / AR287 337 407-Operation Manual
File
ar-337-sm8.pdf
Date

Sharp AR-337 (serv.man8) User Manual / Operation Manual ▷ View online

2-2
CHAPTER
2
AUDITING ACCOUNTS
If this copier has been programmed in the auditing mode, it will not
function until an assigned 5-digit account number has been entered.
★ KEY OPERATOR
See page 8-9 for setting the auditing mode.
MAKING COPIES  
Auditing accounts
The initial status of the message display will be:
ENTER YOUR ACCOUNT NUMBER. -----
Enter your account number using the 10-key pad.
As each digit is entered, the dashes in the display will change to
asterisks.
The following message will appear after the number is entered.
ACCOUNT STATUS: COPIES MADE 000,000
           COPIES REMAINING 000,000
“COPIES REMAINING” will appear only if account limit has been
set using a key operator program.
★ KEY OPERATOR
See page 8-12 for account limit settings.
The message, however, will not be displayed when the printer
auditing mode is enabled by the key operator program with the
optional printer expansion kit installed. Then the account limit
setting will be cancelled.
★ KEY OPERATOR
See page 46 of the AR-PB2A operation
manual for the printer auditing mode setting.
The message will be displayed for several seconds, then change
to the following message.
READY TO COPY.
When a copy run is performed, the following message will
appear.
READY TO COPY.
PRESS [AUDIT CLEAR] WHEN FINISHED.
In the interrupt copy mode (see page 2-20), the following
message will appear instead of the message above.
READY TO COPY. WHEN COPYING IS
FINISHED, PRESS [INTERRUPT].
NOTE:
If an unassigned number is entered, the message display will show
ENTER YOUR ACCOUNT NUMBER.-----
”, indicating that the
number was not accepted.
When the key operator program of account number security has
been set:
If an unassigned number is entered three successive times, the
copier will not accept another number for one minute, and the
following message will appear.
PLEASE SEE YOUR KEY OPERATOR FOR
ASSISTANCE.
★ KEY OPERATOR
See page 8-13 for account number
security.
1
2
3
4
5
6
7
8
9
0
C
P
CLEAR
PROGRAM
AUDIT CLEAR
INTERRUPT
1-1
CHAPTER
1
CHAPTER 1
GETTING STARTED
This chapter describes the basic information on the use of this copier.
                                    
  
Page
INSTALLATION REQUIREMENTS
.....................
1-2
CAUTIONS
......................................
1-3
POWER ON AND OFF
..............................
1-5
Power save modes
.................................
1-6
INFORMATION FUNCTION
..........................
1-7
USING THE TOUCH  PANEL
..........................
1-8
How to use the touch panel
...........................
1-8
Selection of function
................................
1-8
Function setting icons
...............................
1-9
1-2
CHAPTER
1
INSTALLATION REQUIREMENTS
To ensure safety and proper machine performance, please note the following
before initial installation and whenever the machine is to be relocated.
1.
The copier should be installed near an accessible power outlet for easy
connection.
2.
Be sure to connect the power cord only to a power outlet that meets the
specified voltage and current requirements.
Also make certain the outlet is properly grounded.
For this copier’s power supply requirements, see the name plate
located on the left hand side at the rear corner of the copier.
3.
Do not install the machine where it is:
damp or humid,
exposed to direct sunlight,
extremely dusty,
poorly ventilated,
subject to extreme temperature or humidity changes (e.g., near an air
conditioner or heater).
4.
Since a hard disk drive is built into this copier, place the copier on a firm,
level surface. Choose an area which is not subject to any vibration.
5.
Be sure to allow the required space around the machine for servicing and
proper ventilation.
GETTING STARTED  
Installation requirements
30 cm
(11-13/16")
60 cm
(23-5/8")
60 cm
(23-5/8")
30 cm
(11-13/16")
1-3
CHAPTER
1
CAUTIONS
1.
Do not touch the photoconductive drum. Scratches or
smudges on the drum will cause dirty copies.
2.
The fusing unit is extremely hot.  Exercise care in this area.
3. Since a hard disk drive is built into the copier, be sure to turn the
power switch to the “OFF” position when moving the copier. Take
care not to subject the copier to any vibration or shock.
4.
Do not look directly  at the light source. Doing so may
damage your eyes.
5.
Four installation adjusters are provided on the optional
stand/500-sheet paper drawer.
When moving the machine with the optional stand/
500-sheet paper drawer, be sure to raise the installation
adjusters. After moving the machine, lower the four installation
adjusters until they reach the floor and lock the two casters
at the front of the copier.
6. When copying is interrupted (for example, because the
INTERRUPT function has been used, paper or toner has run out,
a misfeed has occurred, etc.), this copier will store the image
data of the originals read prior to the interruption. If copying of
secret documents is interrupted due to the above reasons, be
sure to either resume the interrupted copying by pressing the
START (
) key, or clear the image data by pressing the CLEAR
ALL (
CA
) key after the interrupt copying is completed or the
trouble is cleared, because the stored data may be printed by
other operators.
GETTING STARTED  
Cautions
Fusing unit
Photoconductive
drum
Lock
Release
Adjuster
Lock
Caster
Release
Caution
This product contains a low power laser device. To
ensure continued safety do not remove any cover or
attempt to gain access to the inside of the product. Refer
all servicing to qualified personnel.
At the production line, the output power of
the scanner unit is adjusted to 0.6 MILLI-
WATT PLUS 8 PCTS and is maintained
constant by the operation of the Automatic
Power Control (APC).
Cautions on laser
Wave length
785 nm
 +10 nm
              -15 nm
Pulse times
North America: (2.274 µs ±2.3 ns)/7 mm
Europe: (3.025 µs ±3.0 ns)/7 mm
Output power
0.24 - 0.60 mW
Page of 127
Display

Sharp AR-337 (serv.man8) User Manual / Operation Manual ▷ Download

  • DOWNLOAD Sharp AR-337 (serv.man8) Service Manual ↓ Size: 4.65 MB | Pages: 127 in PDF or view online for FREE
  • Here you can View online or download the User Manual / Operation Manual for the Sharp AR-337 (serv.man8) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp AR-337 (serv.man8) Copying Equipment. Information contained in Sharp AR-337 (serv.man8) User Manual / Operation Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.