DOWNLOAD Sharp AR-335 (serv.man36) Service Manual ↓ Size: 184.36 KB | Pages: 32 in PDF or view online for FREE

                                      

Page

●

8-2

●  

Registering the key operator code number

8-2

●

8-4

●  

Using the key operator programs

8-7

●

8-28

●

8-29

This chapter contains information on all of the
programs used by the key operator. The programs
allow the key operator to tailor many functions of
the AR-280/AR-285/AR-335 for specific modes of
operation. These programs can only be accessed
after a key operator code number has been entered.
Please familiarise yourself with this chapter and
refer to it for the information you need to keep the
copier operating smoothly.

●

The following display will appear.

●

When registering the key operator code number for the first time,
enter the number that was set at the factory. (See page 8-29.)

●

As the code number is entered, the dashes in the display will
change to asterisks.

CUSTOM SETTINGS

EXPOSURE

PAPER SELECT

COPY RATIO

EXIT

DISPLAY
CONTRAST

KEY OPERATOR

PROGRAMS

KEY OPERATOR PROGRAMS

EXIT

COPIER

TOTAL COUNT.

PROGRAM LIST
PRINTOUT.

COPIER

PDA/ZR

KEY OPERATOR PROGRAMS

COPIER MODE

OTHER FUNCTION
SETTINGS

ENABLE/DISABLE
SETTINGS

TIMER SETTINGS

ACCOUNT CONTROL

KEY OPERATOR PROGRAMS

ENTER KEY OPERATOR CODE.

EXIT

A key operator code number must be registered before a key operator
program can be used. The key operator must remember this number. Only
this registered number will allow access to the key operator programs.

Key operator code number

1

2

3

4

5

6

0

C

7

8

9

P

CLEAR

PROGRAM

AUDIT CLEAR

INTERRUPT

●

The code number will change from the previous setting to the
new setting.

CA

KEY OPERATOR PROGRAMS

OTHER FUNCTION SETTINGS

KEY OPERATOR CODE NUMBER
CHANGE.

EXPOSURE ADJUSTMENT.

ADD OR CHANGE EXTRA PRESET
RATIOS.

TONER SAVE MODE.

R:0

E:0

AE:3

1/4

1

2

3

4

5

6

7

8

9

0

C

P

CLEAR

PROGRAM

AUDIT CLEAR

INTERRUPT

KEY OPERATOR PROGRAMS

INPUT A NEW CODE NUMBER AND PRESS [OK].

KEY OPERATOR CODE
NUMBER CHANGE.

98765

PRESENT

NEW

Key operator code number

A complete list of all key operator programs is provided below. These programs can
only be accessed by first entering the key operator code number.
The key operator programs are grouped into four categories: account control, other
function settings, timer settings, and enable/disable settings.

Category

Program Name

Function

 Page No.

Account Control

Auditing Mode

Enables or disables the basic auditing mode, which

8-9

controls access to copier.

Number of Copies

Displays the total number of copies made against

8-9

per Account

account numbers.

Resetting Account

Resets all audit accounts or selectively resets

8-10

individual accounts.

Account Number

Registers accounts, deletes accounts, changes an

8-10

Control

account number, or prints all registered account
numbers.

Account Limit

Sets the maximum number of copies which can be

8-12

Setting

made against a registered account number.

Account Number

Guards against trial and error entering of audit

8-13

Security

account numbers.

Other Function

Key Operator Code

Changes the key operator code number.

8-14

Settings

Number Change

Exposure

Lightens or darkens copies in the automatic

8-14

Adjustment

exposure mode.

Toner Save Mode

Reduces toner consumption.

8-14

Add or Change

Adds or changes reduction and enlargement preset

8-15

Extra Preset Ratios

copy ratios.

Setting a Maximum

Sets the maximum number of copies that can be

8-15

Number of Copies

selected.

Initial Margin Shift

Sets the initial margin shift values.

8-16

Setting

Erase Width

Sets the initial amount of the erase area.

8-16

Adjustment

Initial Status

Sets the copier’s initial settings in the ready

8-17

Setting

condition.

Stream Feeding

Enables the stream feeding mode for copying

8-17

Mode

from the document feeder.

Staple Position

Sets the initial stapling position setting for an optional

8-18

Setting

finisher (AR-FN1).

Key operator programs