DOWNLOAD Sharp AR-285 (serv.man9) Service Manual ↓ Size: 552.83 KB | Pages: 12 in PDF or view online for FREE

Tilt the toner box lever toward you, and pull out the toner box.

Shake the toner cartridge vertically about 20 times.

Attach the toner cartridge to the toner box.

Insert two projections of the toner cartridge into the notches f the
toner supply port.

Move the toner cartridge in the arrow direction until it stops.

Take off the seal end and slowly remove it.

When removing the seal, hold and fix the toner cartridge.

Tap the top of the toner cartridge several times.

This is to shake off toner attached to the side surface of the toner
cartridge.

Move the empty toner cartridge in the arrow direction and remove
it.

Push the toner box to the original position, and put the toner box
lever to the original position.

20 x

 

5 – 8

CLose the front cabinet.

(When installing the RADF)

Temporarily fix tray fixing screw (M4 x 8), and connect the RADF
connector with the tray connector.

Install the tray as shown in the figure below, and tighten the fixing
screws (2 pcs.).

Press the CUSTOM SETTINGS key.

Press the "DISPLAY CONTRAST" key on the touch panel.

Press the "LIGHTER" or "DARKER" key to adjust the contrast.

Press the "OK" key.

Tray side connector

Tray
fixing
screw

ADF side connector

Tray

Tray
fixing
screw

5 – 9

When the standard lamp lights up after turning on the power, or when
one minute passed after completion of copying, or when the all clear
key is pressed, the mode returns to the standard state.

<The time can be changed by the key operator.>

Standard state list

<When shipping from the factory, the above state is set, however, it
can be changed by the key operator.>

When the time set by the key operator passes, power supply to the
fusing section is cur off to reduce power consumption. This is the
auto power shut off function.

In this mode, the touch panel display disappears and only the START
key display lamp blinks.

To cancel the auto power shut off mode, press the START key.

The machine will be ready for operation in about 65 sec.

<This mode can be set by the key operator. As the factory setting, the
machine is set to enter the auto power shut off mode after about
60min of leaving.>

Pre-heat mode means when the time set by the key operator passes,
the temperature in the fusing section is automatically lowered to shift
to the low power consumption mode in order to reduce power con-
sumption in the standby mode.

In the pre-heat mode, when an original is set on the automatic docu-
ment feeder, or when copy setting is made, the pre-heat mode is
canceled.

It takes about 30 sec to recover from canceling the pre-heat mode to
enter the operatable mode.

Compared to the auto power shut off mode, the saved power is less
but the recovery time is smaller.

<This mode can be set by the key operator. As the factory setting, the
machine is set to enter the pre-heat mode after about 15 min of
leaving.>

Copy density
adjustment = Auto

Copy quantity
display = 0

Selection tray
(Highlighted display)
 = Pre-selection tray

Magnification ratio
 = 100% (Normal)

Paper/magnification ratio automatic
selection + Paper automatic selection
state ("AUTO" is displayed on the
paper selection key.)

5 – 10

When the standard lamp lights up after turning on the power, or when
one minute passed after completion of copying, or when the all clear
key is pressed, the mode returns to the standard state.

<The time can be changed by the key operator.>

Standard state list

<When shipping from the factory, the above state is set, however, it
can be changed by the key operator.>

When the time set by the key operator passes, power supply to the
fusing section is cur off to reduce power consumption. This is the
auto power shut off function.

In this mode, the touch panel display disappears and only the START
key display lamp blinks.

To cancel the auto power shut off mode, press the START key.

The machine will be ready for operation in about 65 sec.

<This mode can be set by the key operator. As the factory setting, the
machine is set to enter the auto power shut off mode after about
60min of leaving.>

Pre-heat mode means when the time set by the key operator passes,
the temperature in the fusing section is automatically lowered to shift
to the low power consumption mode in order to reduce power con-
sumption in the standby mode.

In the pre-heat mode, when an original is set on the automatic docu-
ment feeder, or when copy setting is made, the pre-heat mode is
canceled.

It takes about 30 sec to recover from canceling the pre-heat mode to
enter the operatable mode.

Compared to the auto power shut off mode, the saved power is less
but the recovery time is smaller.

<This mode can be set by the key operator. As the factory setting, the
machine is set to enter the pre-heat mode after about 15 min of
leaving.>

Copy density
adjustment = Auto

Copy quantity
display = 0

Selection tray
(Highlighted display)
 = Pre-selection tray

Magnification ratio
 = 100% (Normal)

Paper/magnification ratio automatic
selection + Paper automatic selection
state ("AUTO" is displayed on the
paper selection key.)

5 – 10