Sharp AR-285 (serv.man36) User Manual / Operation Manual ▷ View online
8-16
CHAPTER
8
KEY OPERATOR PROGRAMS
Initial Margin Shift Setting
Set the initial margin shift value with this program.
When the “INITIAL MARGIN SHIFT SETTING.” key is pressed, the
following display will appear.
When the “INITIAL MARGIN SHIFT SETTING.” key is pressed, the
following display will appear.
1.
Adjust the value for each side using the
and
keys.
●
The value can be set from 0 mm to 20 mm in 1 mm increments
(0" to 1" in 1/8" increments).
(0" to 1" in 1/8" increments).
●
If an optional duplex module (AR-DU1) is not installed in the AR-
280, the value for the reverse side (side 2) is not displayed.
280, the value for the reverse side (side 2) is not displayed.
2.
Press the “OK” key.
Erase Width Adjustment
Set the initial setting of the amount of the erase area with this program.
When the “ERASE WIDTH ADJUSTMENT.” key is pressed, the
following display will appear.
When the “ERASE WIDTH ADJUSTMENT.” key is pressed, the
following display will appear.
1.
Adjust the values for the edge erase mode and centre
erase mode using the
erase mode using the
and
keys.
●
The values can be set from 0 mm to 20 mm in 1 mm increments
(0" to 1" in 1/8" increments).
(0" to 1" in 1/8" increments).
2.
Press the “OK” key.
OK
CANCEL
KEY OPERATOR PROGRAMS
INITIAL MARGIN SHIFT
SETTING.
SET THE INITIAL MARGIN SHIFT.
SIDE 1
(0~20)
mm
mm
SIDE 2
(0~20)
mm
mm
10
10
OK
KEY OPERATOR PROGRAMS
ERASE WIDTH
ADJUSTMENT.
SET THE INITIAL ERASE WIDTH.
EDGE ERASE
(0~20)
mm
mm
CENTRE ERASE
(0~20)
mm
mm
OK
10
10
KEY OPERATOR’S GUIDE
Key operator programs
8-17
CHAPTER
8
KEY OPERATOR PROGRAMS
Initial Status Setting
The copier will assume the initial settings when it is turned on, when
the CLEAR ALL (
the CLEAR ALL (
CA
) key is pressed, or when the auto clear interval
has elapsed after a copy run. Use this program to establish the initial
settings.
When the “INITIAL STATUS SETTING.” key is pressed, the following
display will appear.
settings.
When the “INITIAL STATUS SETTING.” key is pressed, the following
display will appear.
To establish new initial settings
1.
Press the “ESTABLISH NEW INITIAL SETTINGS.” key.
2.
Select all initial settings on the operation panel.
●
The following functions cannot be set:
Number of copies, XY zoom, automatic copy ratio selection,
interrupt, special functions, information, stapling position (for an
optional finisher (AR-FN1)) and LCD contrast.
Number of copies, XY zoom, automatic copy ratio selection,
interrupt, special functions, information, stapling position (for an
optional finisher (AR-FN1)) and LCD contrast.
3.
Press the “OK” key.
To return to the factory default settings
Press the “RETURN TO THE FACTORY DEFAULT SETTINGS.”
key.
key.
Stream Feeding Mode
This program is used to enable the stream feeding mode of the
document feeder. When the stream feeding mode is enabled, additional
originals which are set in the document feeder tray within 5 seconds
after the previous original was fed will be fed and copied automatically.
document feeder. When the stream feeding mode is enabled, additional
originals which are set in the document feeder tray within 5 seconds
after the previous original was fed will be fed and copied automatically.
To enable the stream feeding mode, press the check box of
“STREAM FEEDING MODE.” to display a check mark in the
check box.
To disable this mode, press the check box of this program
again to clear the check mark in the check box.
“STREAM FEEDING MODE.” to display a check mark in the
check box.
To disable this mode, press the check box of this program
again to clear the check mark in the check box.
●
The stream feeding mode will only function when the group mode has
been selected.
been selected.
KEY OPERATOR PROGRAMS
INITIAL STATUS SETTING.
SET THE INITIAL STATUS.
ESTABLISH NEW INITIAL
SETTINGS.
RETURN TO THE FACTORY DEFAULT
SETTINGS.
OK
1/4
1/4
KEY OPERATOR’S GUIDE
Key operator programs
8-18
CHAPTER
8
Staple Position Setting
This program is used to select the initial stapling position for an
optional finisher (AR-FN1).
When the “STAPLE POSITION SETTING.” key is pressed, the
following display will appear.
optional finisher (AR-FN1).
When the “STAPLE POSITION SETTING.” key is pressed, the
following display will appear.
1.
Select the desired stapling position on the touch panel.
2.
Press the “OK” key.
Date Format Setting
This program is used to set the initial date format for the date function.
When the “DATE FORMAT SETTING.” key is pressed, the following
display will appear.
When the “DATE FORMAT SETTING.” key is pressed, the following
display will appear.
1.
Select the desired date format on the touch panel.
●
The date formats displayed on the touch panel may be different
from the illustration above depending on the country or region.
from the illustration above depending on the country or region.
2.
Press the “OK” key.
KEY OPERATOR PROGRAMS
KEY OPERATOR PROGRAMS
STAPLE POSITION
SETTING.
OK
KEY OPERATOR PROGRAMS
23 April, 1998
April 23, 1998
23/04/98
04/23/98
DATE FORMAT SETTING.
OK
KEY OPERATOR’S GUIDE
Key operator programs
8-19
CHAPTER
8
Date and Time Adjustment
This program is used to adjust the date and time which will be used for
printing date.
When the “DATE AND TIME ADJUSTMENT.” key is pressed, the
following display will appear.
printing date.
When the “DATE AND TIME ADJUSTMENT.” key is pressed, the
following display will appear.
1.
Select an item to be adjusted and adjust the value using
the
the
and
keys.
●
Repeat this step for all desired items.
2.
Press the “OK” key.
●
If an invalid date (example: February 31) has been entered in
step 1, the “OK” key will be disabled.
step 1, the “OK” key will be disabled.
Rotation Copy Setting
If this program is set, the image of originals will rotate when the
orientation of the originals does not match that of the copy paper.
Rotation copy will function only when the auto paper select or auto
copy ratio mode has been selected.
When the STAPLE SORT function is used, rotation copy will not be
performed even if this program has been set.
orientation of the originals does not match that of the copy paper.
Rotation copy will function only when the auto paper select or auto
copy ratio mode has been selected.
When the STAPLE SORT function is used, rotation copy will not be
performed even if this program has been set.
NOTE:
If the image is rotated in reduction copying, the position of the image
in relation to copy paper will vary with the orientations of the originals
and copy paper.
If the image is rotated in reduction copying, the position of the image
in relation to copy paper will vary with the orientations of the originals
and copy paper.
To enable rotation copy, press the check box of “ROTATION
COPY SETTING.” to display a check mark in the check box.
To disable this mode, press the check box of this program
again to clear the check mark in the check box.
COPY SETTING.” to display a check mark in the check box.
To disable this mode, press the check box of this program
again to clear the check mark in the check box.
KEY OPERATOR PROGRAMS
DATE AND TIME ADJUSTMENT.
YEAR
1998
MONTH
10
DAY
12
HOUR
00
(00~23)
MINUTE
00
OK
KEY OPERATOR PROGRAMS
KEY OPERATOR’S GUIDE
Key operator programs
Original
Copy paper
Copy
Click on the first or last page to see other AR-285 (serv.man36) service manuals if exist.