DOWNLOAD Sharp AR-285 (serv.man34) Service Manual ↓ Size: 1.68 MB | Pages: 78 in PDF or view online for FREE

Model
AR-285 (serv.man34)
Pages
78
Size
1.68 MB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Copying Equipment / AR280 285 335 Operation Manual-Section 1
File
ar-285-sm34.pdf
Date

Sharp AR-285 (serv.man34) User Manual / Operation Manual ▷ View online

1-6
CHAPTER
1
GETTING STARTED  
Power on and off
Auto power shut-off mode
If the auto power shut-off mode is enabled, the copier will
automatically turn off the power once a programmed length of time
has elapsed without any copier operation after the last copy of a run
is made or the power is first turned on. The power switch will
automatically be turned to the “OFF” position.
To turn the power back on, simply turn the power switch to the “ON”
position.
★ KEY OPERATOR See page 8-21 for setting the auto power shut-off
timer. See page 8-26 for enabling or disabling the auto power shut-off
mode.
Preheat mode
The copier will enter the mode once the set time has elapsed
without any copier operation after the last copy of a run is made or
power is turned on.
When the copier enters the preheat mode, the message “
PREHEAT
MODE. PLACE ORIGINALS
.” will appear.
In this condition, the fuser in the copier is maintained at a lower heat
level thereby saving power. The preheat level is, however, high
enough to allow the copier to come to a ready condition or begin
copying approximately 30 seconds after any key input is made.
To copy from the preheat mode, make desired copier selections and
press the START (
) key using the normal copying procedure.
★ KEY OPERATOR See page 8-22 for information on setting the preheat
mode.
POWER ON AND OFF
1-7
CHAPTER
1
1
Press the INFORMATION (
) key in the standby mode.
The screen for the information categories will appear.
2
Select the “COPIER” key to display the first screen of
the copier feature items.
If the toner supply is not low, this step is not needed.
3
Select the feature you would like to know about by
pressing a copier feature item key on the touch panel.
If the feature you would like to know about is not displayed on
the touch panel, press the scroll (
) key on the touch panel
until the feature is displayed.
If a copier feature item key is pressed, the description for that
feature will appear. Use the scroll (
) key to display additional
information until all information for that feature has been
displayed.
To return to the copier feature item screen, press the “INDEX”
key.
To exit the INFORMATION mode, press the “EXIT” key on the
touch panel.
INFORMATION FUNCTION
The information function provides a quick reference guide to the use
of the various features and functions of this copier. The information
mode can be entered when the copier is in the standby mode.
GETTING STARTED  
Information function
1
4
EXIT
MAKING 2-SIDED COPIES (2-SIDED COPY)
INFORMATION
SORTING COPIES INTO SETS OR STAPLING
FINISHED SETS OF COPIES (OUTPUT)
USING THE DOCUMENT FEEDER
(DOCUMENT FEEDER)
REDUCTION/ENLARGEMENT/ZOOM
(COPY RATIO)
STORING FREQUENTLY USED JOB PROGRAMS 
(PROGRAM)
1/5
EXIT
INFORMATION
SELECT INFORMATION.
COPIER
ADDING TONER
INSTRUCTIONS
1-8
CHAPTER
1
USING THE TOUCH PANEL
How to use the touch panel
You can set or cancel a function displayed on the touch
panel by pressing (touching) a key with a finger. The touch
key operation can be confirmed with a beep tone (and
highlighted display).
★ KEY OPERATOR For the beep tone to be heard, the beep tone must be
enabled by a key operator program. See page 8-26.
If any keys are displayed gray, the keys have been disabled.
If you press these keys, two short beeps will be sounded.
Selection of function
To register the selected settings for a function, press the
“OK” key on the setting screen. The settings indicated by
a highlighted display will be registered as a selected function.
Some special functions can be selected by pressing the
relevant keys on the SPECIAL MODES screen (page 3-4) or
on the IMAGE EDIT menu (page 3-21) to highlight the keys.
To cancel these functions, press the relevant keys again to
return the keys to the normal display. These functions are:
Dual page copying, Centring, Hi-Fi copy, B/W reverse, and
Binding change.
GETTING STARTED  
Using the touch panel
READY TO COPY. 
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
AUTO 8/ 11
1
2
1.
 A4
2. A3
STORE/DELETE
RECALL
ERASE
EDGE ERASE
CENTRE ERASE
EDGE+CENTRE
ERASE
CANCEL
 10
OK
OK
(0~20)
mm
READY TO COPY. 
SPECIAL MODES
MARGIN SHIFT
MULTI SHOT
PAMPHLET COPY
ERASE
COVERS
IMAGE EDIT
TEXT STAMP
TRANSPARENCY
INSERTS
DUAL PAGE
COPY
OK
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
AUTO A4
1-9
CHAPTER
1
Function setting icons
Selected special functions are indicated with their icons on
the basic screen. The setting screen for a selected function
can be easily called by pressing its icon. (The functions
indicated below with *1 have no setting screen and, therefore,
no setting screen can be called.)
If multiple special functions are selected, up to six icons will
be displayed.
The function setting icons are listed below. The content of
the icons indicated by *2 will change depending upon the
particular settings for these functions.
USING THE TOUCH PANEL
GETTING STARTED  
Using the touch panel
READY TO COPY. 
1. A4
2. A3
READY TO COPY. 
ERASE
EDGE ERASE
CENTRE ERASE
EDGE+CENTRE
ERASE
CANCEL
10
OK
OK
(0~20)
mm
*
2
 Margin shift (p.3-4)
*
2
 Erase (p.3-6)
*
1
 Dual page copying (p.3-8)
*
2
 Multi shot (p.3-10)
*
2
 Covers (p.3-13)
*
2
 Transparency film with insert sheets
(p.3-15) 
 Pamphlet copy (p.3-17)
*
1
 Centring (p.3-20)
*
2
 Repeat copy (p.3-22)
*
1
 Hi-Fi (p.3-25)
*
1
 B/W reverse (p.3-27)
*
1
 Binding change (p.3-29)
 
 Date (p.3-32)
 Select stamp (p.3-35)
 
 Watermark (p.3-38)
 Page number (p.3-41)
Page of 78
Display

Click on the first or last page to see other AR-285 (serv.man34) service manuals if exist.