Sharp AR-285 (serv.man34) User Manual / Operation Manual ▷ View online
2-2
CHAPTER
2
AUDITING ACCOUNTS
If this copier has been programmed in the auditing mode, it will not
function until an assigned 5-digit account number has been entered.
function until an assigned 5-digit account number has been entered.
★ KEY OPERATOR
See page 8-9 for setting the auditing mode.
MAKING COPIES
Auditing accounts
The initial status of the message display will be:
ENTER YOUR ACCOUNT NUMBER. –––––
●
Enter your account number using the 10-key pad.
●
As each digit is entered, the dashes in the display will change to
asterisks.
asterisks.
The following message will appear after the number is entered.
ACCOUNT STATUS: COPIES MADE 000,000
COPIES REMAINING 000,000
COPIES REMAINING 000,000
“COPIES REMAINING” will appear only if account limit has been
set using a key operator program.
set using a key operator program.
★ KEY OPERATOR
See page 8-12 for account limit settings.
●
The message will be displayed for several seconds, then
change to the following message.
change to the following message.
READY TO COPY.
●
When a copy run is performed, the following message will
appear.
appear.
READY TO COPY.
PRESS [AUDIT CLEAR] WHEN FINISHED.
PRESS [AUDIT CLEAR] WHEN FINISHED.
(In some regions, [ACC.#-C] is displayed in place of [AUDIT
CLEAR].)
CLEAR].)
●
In the interrupt copy mode (see page 2-20), the following
message will appear instead of the message above.
message will appear instead of the message above.
READY TO COPY. WHEN COPYING IS
FINISHED, PRESS [INTERRUPT].
FINISHED, PRESS [INTERRUPT].
NOTE:
If an unassigned number is entered, the message display will show
“
If an unassigned number is entered, the message display will show
“
ENTER YOUR ACCOUNT NUMBER.-----
”, indicating that the
number was not accepted.
When the key operator program of account number security has
been set:
If an unassigned number is entered three successive times, the
copier will not accept another number for one minute, and the
following message will appear.
been set:
If an unassigned number is entered three successive times, the
copier will not accept another number for one minute, and the
following message will appear.
PLEASE SEE YOUR KEY OPERATOR FOR
ASSISTANCE.
ASSISTANCE.
★ KEY OPERATOR
See page 8-13 for account number
security.
1
2
3
4
5
6
7
8
9
0
C
P
CLEAR
PROGRAM
AUDIT CLEAR
INTERRUPT
2-3
CHAPTER
2
USING THE SPF/RADF
●
Duplex copying will not work when a non-standard
sized paper (or 5-1/2" x 8-1/2" paper) is used.
sized paper (or 5-1/2" x 8-1/2" paper) is used.
●
If the orientation of the originals does not match that
of the copy paper when both the originals and copy
paper are of standard sizes and the auto paper select
mode or automatic copy ratio select mode is on, the
image of the originals will be automatically rotated to
match the copy paper. However, if enlargement
copying onto a paper size larger than A4 (8-1/2" x
11") is performed, the image will not be rotated.
of the copy paper when both the originals and copy
paper are of standard sizes and the auto paper select
mode or automatic copy ratio select mode is on, the
image of the originals will be automatically rotated to
match the copy paper. However, if enlargement
copying onto a paper size larger than A4 (8-1/2" x
11") is performed, the image will not be rotated.
●
Image loss (max. 5mm (13/64")) can occur along the
leading and trailing edges of the copies. Also image
loss (max. 5mm (13/64") in total) can occur along the
other edges of the copies.
leading and trailing edges of the copies. Also image
loss (max. 5mm (13/64") in total) can occur along the
other edges of the copies.
The SPF* (single pass feeder) and the RADF* (reversing
automatic document feeder) will handle multiple
originals.
* The SPF is installed to the AR-280 and the RADF is
automatic document feeder) will handle multiple
originals.
* The SPF is installed to the AR-280 and the RADF is
installed to the AR-285 and AR-335.
●
Before loading originals into the document feeder
tray, be sure to remove any staples or paper clips
from them.
tray, be sure to remove any staples or paper clips
from them.
●
Damaged or crumpled originals or originals which
have been folded may misfeed in the SPF/RADF or
cause incorrect size detection. It is recommended
that these be copied from the document glass and
the copies be used as original documents.
have been folded may misfeed in the SPF/RADF or
cause incorrect size detection. It is recommended
that these be copied from the document glass and
the copies be used as original documents.
●
When feeding originals which have closely spaced
binding holes punched along an edge, place the
originals so that the punched edge is positioned to
the right or along the side guides.
binding holes punched along an edge, place the
originals so that the punched edge is positioned to
the right or along the side guides.
●
Special originals such as transparency film and tracing
paper should not be fed from the SPF/RADF, but
should be placed on the document glass.
paper should not be fed from the SPF/RADF, but
should be placed on the document glass.
Stream feeding mode
If the stream feeding mode has been enabled using a key operator
program, the message “
If the stream feeding mode has been enabled using a key operator
program, the message “
NEWLY PLACED ORIGINALS WILL BE FED
AND COPIED AUTOMATICALLY.
” will appear and the original feed
indicator (AR-285/AR-335 only) will continue to blink for approximately
5 seconds after feeding of all originals is completed. While this
message is displayed, any new originals placed in the document
feeder tray will be fed and copied automatically.
5 seconds after feeding of all originals is completed. While this
message is displayed, any new originals placed in the document
feeder tray will be fed and copied automatically.
★ KEY OPERATOR
See page 8-17 for information on setting the
stream feeding mode.
MAKING COPIES
Using the SPF/RADF
Notes on the SPF (AR-280)
●
The SPF can handle a maximum of 30 originals of A5
to A4 (5-1/2" x 8-1/2" to 8-1/2" x 11") sizes and 15
originals of B4 to A3 (8-1/2" x 14" to 11" x 17") sizes.
to A4 (5-1/2" x 8-1/2" to 8-1/2" x 11") sizes and 15
originals of B4 to A3 (8-1/2" x 14" to 11" x 17") sizes.
●
2-sided to 1-sided copying and 2-sided to 2-sided
copying cannot be performed in this model.
copying cannot be performed in this model.
●
The originals must be set face down in the document
feeder tray.
feeder tray.
●
Do not place different size originals in the document
feeder tray. Doing so may cause copying onto different
sizes or original misfeeds.
feeder tray. Doing so may cause copying onto different
sizes or original misfeeds.
Notes on the RADF (AR-285 and AR-335)
●
The RADF can handle a maximum of 50 originals of
A5 to A4 (5-1/2" x 8-1/2" to 8-1/2" x 11") sizes and 30
originals of B4 to A3 (8-1/2" x 14" to 11" x 17") sizes.
A5 to A4 (5-1/2" x 8-1/2" to 8-1/2" x 11") sizes and 30
originals of B4 to A3 (8-1/2" x 14" to 11" x 17") sizes.
●
2-sided to 1-sided copying and 2-sided to 2-sided
copying can be performed in these models.
copying can be performed in these models.
●
The originals must be set face up in the document
feeder tray.
feeder tray.
●
Different size originals with the same width can be
placed in the document feeder tray and automatically
copied onto copy paper of their respective sizes.
The automatic copy ratio selection will not function in
this case.
placed in the document feeder tray and automatically
copied onto copy paper of their respective sizes.
The automatic copy ratio selection will not function in
this case.
2-4
CHAPTER
2
1-sided copies of 1-sided originals
1
Adjust the original guides to the size of the originals and
set the originals face down (AR-280) or face up (AR-285/
AR-335) in the document feeder tray.
set the originals face down (AR-280) or face up (AR-285/
AR-335) in the document feeder tray.
●
The original size will be indicated on the touch panel, and the
paper tray with the corresponding paper size will be automatically
selected.
paper tray with the corresponding paper size will be automatically
selected.
●
Be sure to remove any original from the document glass before
setting the originals in the document feeder tray. In the AR-285
and AR-335, if an original is left on the document glass, the
original reminder indicator will blink. Remove the original from
the document glass in this case.
setting the originals in the document feeder tray. In the AR-285
and AR-335, if an original is left on the document glass, the
original reminder indicator will blink. Remove the original from
the document glass in this case.
●
If copy paper of the required size is not installed in any of the
trays, the following message will appear.
trays, the following message will appear.
LOAD
PAPER.
If a tray of the required size is not installed, use the bypass tray
and press the “PAPER SELECT” key on the touch panel to
select the bypass tray.
and press the “PAPER SELECT” key on the touch panel to
select the bypass tray.
●
To copy onto a different size paper, use the “PAPER SELECT”
key to make the selection.
key to make the selection.
2
Ensure that the 1-sided to 1-sided copying mode is
selected on the touch panel.
selected on the touch panel.
●
When no icon is displayed in the area indicated in the illustration
(
(
), the 1-sided to 1-sided copying mode is selected.
●
If the 1-sided to 1-sided mode is not selected, press the
2-SIDED COPY key and then press the 1-sided to 1-sided key
(
2-SIDED COPY key and then press the 1-sided to 1-sided key
(
) on the touch panel. Press the “OK” key to return to the
basic screen.
3
Use the 10-key pad to enter the desired number of
copies.
copies.
●
The number will be shown in the copy quantity display of the
touch panel.
touch panel.
●
Use the CLEAR (
C
) key to cancel an entry if a mistake has
been made.
●
If you set a multiple number of copies, the copies will be
delivered collated. To deliver in the GROUP mode, press the
OUTPUT key and then select “GROUP” on the touch panel. See
page 2-17.
delivered collated. To deliver in the GROUP mode, press the
OUTPUT key and then select “GROUP” on the touch panel. See
page 2-17.
4
Press the START (
) key.
●
To cancel a copy run, press the CLEAR ALL (
CA
) key. Copying
will stop and the SPF/RADF will output any originals which have
been fed. Also, the number in the copy quantity display will be
reset to 0.
been fed. Also, the number in the copy quantity display will be
reset to 0.
MAKING COPIES
Using the SPF/RADF
USING THE SPF/RADF
READY TO COPY. (DOCUMENT FEEDER MODE)
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
AUTO A4
1. A4
2. A3
A4
ORIGINAL
1
2
3
4
5
6
7
8
9
0
C
P
CLEAR
PROGRAM
AUDIT CLEAR
INTERRUPT
C
CLEAR
INTERRUPT
CA
CLEAR ALL
START
2-5
CHAPTER
2
MAKING COPIES
Using the SPF/RADF
USING THE SPF/RADF
2-sided copies from 1-sided originals
To copy in the 1-sided to 2-sided copy mode with the AR-280, an
optional duplex module (AR-DU1) must be installed.
optional duplex module (AR-DU1) must be installed.
1
Adjust the original guides to the size of the originals and
set the originals face down (AR-280) or face up (AR-285/
AR-335) in the document feeder tray.
set the originals face down (AR-280) or face up (AR-285/
AR-335) in the document feeder tray.
2
Press the 2-SIDED COPY key.
3
Press the
key on the touch panel.
4
Press the “OK” key.
5
Enter the desired number of copies.
6
Press the START (
) key.
●
To cancel a copy run during duplex copying, press the CLEAR
ALL (
ALL (
CA
) key.
AUTO
1
2
3
4
5
6
7
8
9
0
P
PROGRAM
AUDIT CLEAR
INT
CA
CLEAR ALL
START
READY TO COPY.(DOCUMENT FEEDER MODE)
2-SIDED COPY
OK
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
AUTO A4
READY TO COPY.(DOCUMENT FEEDER MODE)
2-SIDED COPY
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
OK
AUTO A4
Click on the first or last page to see other AR-285 (serv.man34) service manuals if exist.