DOWNLOAD Sharp AR-285 (serv.man2) Service Manual ↓ Size: 207.88 KB | Pages: 52 in PDF or view online for FREE

Model
AR-285 (serv.man2)
Pages
52
Size
207.88 KB
Type
PDF
Document
Handy Guide
Brand
Device
Copying Equipment / Cougar Handy Guide New Version (includes AR250-507 models).
File
ar-285-sm2.pdf
Date

Sharp AR-285 (serv.man2) Handy Guide ▷ View online

 
TEST SIMULATION 
 
SHARP ELECTRONICS (UK) LTD 
DOCUMENT SYSTEMS GROUP
 
26 
VERSION 1 
JANUARY 2002
 
 
 
Test 
Command 
Sub 
Code 
Description 
50 
05 
Adjust print edge position 
 
10 
Print centre deviation adjustment. 
 
12 
Original centre deviation adjustment. 
 
26 
Folding margin of centre binding setting 
51 
01 
PSPS timing set up 
 
02 
Resist roller adjustment value 
 
03 
Clutch Off time setting (AR-507 only) 
 
08 
Used to enable/disable PSPS  timing for each paper 
feed section  
52 
01 
ADU alignment plate home position setting 
53 
-- 
Document Feeder adjustments 
 
01 
DF stop position setting 
 
02 
RADF sensor adjustment 
 
06 
Adjusts RSPF width detection (AR507 only) 
60 
01 DRAM 
test 
61 
-- 
Laser unit  
 
01 
Laser unit check 
 
02 
Laser power value setting (drum type B) 
 
04 
Adjusts scanner laser power in printer mode 
62 
-- Hard 
drive 
 
01 HDD 
format 
 
02 
HDD read/write test partial check 
 
03 
HDD read/write test all area check 
63 
01 
CCD shading data display 
 
07 
White plate scanning start positionadj. (AR507 only) 
64 
01 Self 
print 
65 
-- Touch 
panel 
 
01 
Touch panel adjustment 
 
02 
Touch panel test 
67 
01 
Printer PWB memory operation check 
 
02 
Printer Parallel I/F operation check 
 
03 
Adjust Parallel I/F Ack signal width 
 
11 
Used to set printer I/F select in signal 
 
12 
Used to write data into printer flash memory 
 
13 
Used to check printer flash memory data 
 
14 
Printer flash memory data writing & result 
 
15  
Used to check the sum of the printer flash memory 
 
16 
Used to check the operation of the network card 
 
17 
NVRAM data clear (printer pwb) 
 
18 
Data Clear (Network scanner) 
69 
01 
Used to check input/output of scsi channels A and B 
(AR507 only) 
 
 
TROUBLE CODES 
 
SHARP ELECTRONICS (UK) LTD 
DOCUMENT SYSTEMS GROUP
 
27 
VERSION 1 
JANUARY 2002
 
 
 
 
Sub 
Content of trouble 
 
Code 
Sub 
Content of trouble 
CE 00 
Communication error has occurred 
 
F9 90 
Printer communication trouble 
 01 
AR-NC3D is not installed ot defective 
 
H3 00 
Thermistor open (HL1) 
 02 
Specified Mail Server or FTP server not found 
 
 01 
Thermistor open (HL2) 
 03 
Server does not correspond during image TX 
 
H3 00 
Heat roller high temperature detection (HL1) 
 04 
Entered account name is invalid 
 
 01 
Heat roller high temperature detection (HL2) 
 05 
Entered directory of the FTP server is invalid 
 
H4 00 
Heat roller low temperature detection (HL1) 
Cl 00 
MC trouble 
 
 01 
Heat roller low temperature detection (HL2) 
C2 00 
TC trouble 
 
H5 01 
5 continuous POD not-reaching JAM detection 
E7 00 
ICU communication trouble 
 
 02 
Fusing thermistor abnormality 
 01 
Image data memory trouble 
 
L1 00 
Scanner feed trouble 
 02 
Laser trouble 
 
L3 00 
Scanner return trouble 
 03 
HDD trouble 
 
L4 01 
Main motor lock detection 
 10 
Shading trouble (Black correction) 
 
L6 10 
Polygon motor lock detection 
 11 
Shading trouble (White correction) 
 
L8 01 
No full-wave signal 
 13 
CCD light quantity check error 
 
 02 
Full-wave signal width abnormality 
 90 
CU communication trouble 
 
U2 00 
EEPROM read/write error 
Fl 00 
Finisher communication trouble 
 
 11 
Counter check sum error 
 01 
Finisher 1 jogger shift trouble / 
 
 12 
Adjustment value check sum error 
 02 
Finisher transport motor abnormality 
 
U4 02 
ADU alignment plate operation abnormality 
 04 
Finisher 1 elevator lower limit / 
 
 03 
ADU rear plate operation abnormality 
 
 
Finisher 2 stack tray lower limit 
 
U5 00 
RADF/RSPF/SPFcommunication trouble 
 05 
Finisher 1 elevator home / 
 
 01 
RADF resist sensor trouble 
 
 
Finisher 2 stack tray sensor abnormality 
 
 02 
RADF expulsion sensor trouble 
 06 
Finisher shift motor abnormality 
 
 03 
RADF timing sensor trouble 
 08 
Finisher staple shift motor trouble 
 
 06 
RSP post-separation sensor trouble 
 10 
Finisher staple unit operation trouble 
 
 07 
RSPF read sensor trouble 
 11 
Finisher 1 pusher motor trouble / 
 
 08 
RSPF SB sensor trouble 
 
 
Finisher 2 boomerang rotation abnormality 
 
 11 
RADF paper feed motor operation abnormality 
 14 
Finisher 2 stack tray abnormality 
 
 16 
RSPF fan motor trouble 
 15 
Finisher 1 elevator motor trouble / 
 
U6 00 
Desk communication trouble 
 
 
Finisher 2 stack tray motor lock 
 
 01 
Desk1 CS lift up trouble 
 16 
Staple sort holding motor 
 
 02 
Desk2 CS lift up trouble 
 17 
ST paper exit roller pressure release trouble 
 
 08 
Desk 24v power abnormality 
 18 
Tray 3 paper exit paddler operation trouble 
 
 10 
Desk transport motor trouble 
 50 
Non-support trouble in automatic detection  
 
 20 
LCC communication trouble 
 80 
Finisher power not supplied 
 
 21 
LCC transport motor trouble 
F2 00 
Toner control sensor open 
 
 22 
LCC 24v power abnormality 
 02 
Toner motor connector unconnected 
 
 50 
Non supported option connection (Desk Unit) 
 31 
Process control trouble (Drum surface reflection) 
 
 51 
Non supported option connection (LCC Unit) 
 32 
Process control trouble (Drum Mark) 
 
U7 00 
RIC communication trouble 
 37 
Drum marking sensor gain adjustment error 
 
U9 00 
Operation control communication trouble  (ICU) 
 39 
Process thermistor breakdown 
 
 90 
Operation control communication trouble  (OPE) 
F3 12 
Copier top stage CS lift up trouble 
 
EE EL 
Auto developer adjustment trouble - Overtone 
 22 
Copier bottom stage CS lift up trouble 
 
 EU 
Auto developer adjustment trouble - Undertone 
F9 00 
Printer communication trouble 
 
FA 01 
A2 board self diag error (memory) 
 01 
PRT DRAM trouble 
 
FC 00 
ASK/IrDA modulation LSI reset error 
 02 
PRT Centroport check error 
 
 01 
ASK/IrDA switch error 
 03 
Network card trouble 
 
PC  
Personal counter not installed 
 04 
Printer program error 
 
PF  
RIC copy inhibit command reception 
 05 
Short of memory capacity on the ICU PWB 
 
- - 
 
Auditor not Ready 
 10 
PRT SCSI LSI abnormality 
 
 
 
 
 
JAM CAUSE CODES 
 
SHARP ELECTRONICS (UK) LTD 
DOCUMENT SYSTEMS GROUP
 
28 
VERSION 1 
JANUARY 2002
 
 
 
   CODE 
   CONTENTS 
Copier Body  
MFT   
 
Bypass tray paper jam (PPD2 not reached) 
 
 
 
TRAY1 
 
Tray1 paper feed jam (PFD not reached) 
 
 
 
TRAY2 
 
Tray2 paper feed jam (PFD not reached) 
 
 
 
DUP   
 
Duplex feed jam 
(PPD2 not reached) 
 
PFD_ND1  
PFD not reached jam (Desk tray1 paper feed) 
PFD_ND2 
 
PFD not reached jam (Desk tray2 paper feed) 
 
 
 
 
 
PFD_ST1 
 
PFD remaining jam  (Copier tray1 paper feed) 
 
 
 
PFD_ST2 
 
PFD remaining jam  (Copier tray2 paper feed) 
 
 
 
PFD_SD1 
 
PFD remaining jam  (Desk tray1 paper feed) 
 
 
 
PFD_SD2 
 
PFD remaining jam  (Desk tray2 paper feed) 
 
 
 
 
 
 
PPD1_NT2   
PFD1 not reached jam (Copier tray2 paper feed) 
 
 
 
PPD1_ND1   
PFD1 not reached jam (Desk tray1 paper feed) 
 
 
 
PPD1_ND2   
PFD1 not reached jam (Desk tray2 paper feed) 
 
 
 
PPD1_NLC   
PFD1 not reached jam (LCC paper feed) 
 
 
 
 
PPD1_ST1   
PFD1 remaining jam  (Copier tray1 paper feed) 
 
 
 
PPD1_ST2   
PFD1 remaining jam  (Copier tray2 paper feed) 
 
 
 
PPD1_SD1   
PPD1 remaining jam  (Desk tray1 paper feed) 
 
 
 
PPD1_SD2   
PPD1 remaining jam  (Desk tray2 paper feed) 
 
 
 
PPD1_SLC   
PPD1 remaining jam  (LCC paper feed) 
 
 
 
 
 
PPD2_NT1   
PPD2 not reached jam (Copier tray1 paper feed) 
 
 
 
PPD2_NT2   
PPD2 not reached jam (Copier tray2 paper feed) 
 
 
 
PPD2_ND1   
PPD2 not reached jam (Desk tray1 paper feed) 
 
 
 
PPD2_ND2   
PPD2 not reached jam (Desk tray2 paper feed) 
 
 
 
PPD2_NLC   
PPD2 not reached jam (LCC paper feed) 
 
 
 
 
PPD2_SMF   
PPD2 remaining jam (Bypass paper feed) 
 
 
 
PPD2_ST1   
PPD2 remaining jam (Copier tray1 paper feed) 
 
 
 
PPD2_ST2   
PPD2 remaining jam (Copier tray2 paper feed) 
 
 
 
PPD2_SD1   
PPD2 remaining jam (Desk tray1 paper feed) 
 
 
 
PPD2_SD2   
PPD2 remaining jam (Desk tray2 paper feed) 
 
 
 
PPD2_SLC   
PPD2 remaining jam (LCC paper feed) 
 
 
 
PPD2_SAD   
PPD2 remaining jam (Duplex paper feed) 
 
 
JAM CAUSE CODES 
 
SHARP ELECTRONICS (UK) LTD 
DOCUMENT SYSTEMS GROUP
 
29 
VERSION 1 
JANUARY 2002
 
 
 
   CODE 
   CONTENTS 
 
Copier Body
  
POD1_N 
 
POD1 not reached jam  
(Cont’d) 
 
POD1_S 
 
POD1 remaining jam 
 
 
 
POD1_SU 
 
POD1 remaining jam (upper exit direction) 
 
 
 
POD1_SS 
 
POD1 remaining jam (reversing direction) 
 
 
 
 
POD2_N  
 
POD2 not reached jam  
 
 
 
POD2_S 
 
POD2 remaining jam 
 
 
 
POD3_N 
 
POD3 not reached jam  
 
 
 
POD3_S 
 
POD3 remaining jam  
 
 
 
 
DSBD_N 
 
DSBD not reached jam 
 
 
 
DSBD_SL 
 
DSBD remaining jam (lower exit direction) 
 
 
 
DSBD_SS 
 
DSBD remaining jam (reversing direction) 
 
Duplex Section 
DPPD1_N 
 
DPPD1 not reached jam 
 
 
 
DPPD2_N 
 
DPPD2 not reached jam 
 
 
 
DPPD3_N 
 
DPPD3 not reached jam 
 
 
 
 
 
 
 
DPPD1_S 
 
DPPD1 remaining jam 
 
 
 
DPPD2_S 
 
DPPD2 remaining jam 
 
 
 
DPPD3_S 
 
DPPD3 remaining jam 
 
Desk Unit 
 
DESK1 
 
Desk Tray1 paper feed jam  
 
 
 
DESK2 
 
Desk Tray2 paper feed jam 
 
 
 
 
DPOD1_N 
 
DPOD1 not reached jam 
 
 
 
DPOD2_N 
 
DPOD2 not reached jam 
 
 
 
 
DPOD1_S 
 
DPOD1 remaining jam 
 
 
 
DPOD2_S 
 
DPOD2 remaining jam 
 
 
 
DPOD3_S 
 
DPOD3 remaining jam 
 
LCC Unit 
 
LCC   
 
LCC paper feed jam 
 
 
 
LPFD_S 
 
LPFD remaining jam 
 
Page of 52
Display

Click on the first or last page to see other AR-285 (serv.man2) service manuals if exist.