DOWNLOAD Sharp AR-285 (serv.man167) Service Manual ↓ Size: 49.96 KB | Pages: 2 in PDF or view online for FREE

Model
AR-285 (serv.man167)
Pages
2 Few pages! See other manuals at the bottom of the first or last page.
Size
49.96 KB
Type
PDF
Document
Service Manual / Technical Bulletin
Brand
Device
Copying Equipment / Fault Guide. (WHITE)
File
ar-285-sm167.pdf
Date

Sharp AR-285 (serv.man167) Service Manual / Technical Bulletin ▷ View online

Symptom
Cause
Action
9
Paper jam at FPID when using FN1
Paper exiting copier is ‘bowed’ by the
exit rollers
Remove the pressure springs on the exit
rollers as per installation instructions for
FN2.
10
Locating pins for FN2 front frame side
cannot be screwed in
Either the thread in the hole is missing
or it has been damaged during
removal of the knock out panel
Use the supplied self tap screw to cut the
thread first
11
PFID jam
Paper catches and jams when using
the short path in FN-1
Adjust the position of the short path gate
solenoid.
12
Unable to staple in covers mode when
using FN2
Bypass disabled for use with lower
tray
Reset facility in key op mode
13
Shows paper size as extra when
using bypass
Bypass sensors not set up
Set-up size sensors in SIM 40
14
High noise level from fans in standby
mode
Vibration from ICU board area
Fit modified parts as per FastFax 072
15
‘Bar coded copies’
Main corona grid to tight
Check grid tension is to guide marks
16
Intermittent trail edge blanking
Main corona rear frame end block
cracked
Replace end block
17
Simulation 26-35
Set code to ‘any’ to allow all trouble
history to be recorded
18
Image shift in staple mode on FN-1
Simulation 50
Image alignment must be set-up
accurately in simulation 50, to allow
easier set up enter simulation then close
the screen this will allow Black & White
reverse and staple mode to be selected,
press the area highlighted ‘TEST’
19
Jam Map (22-3)
Abbreviations
A full breakdown of abbreviations is
available on the intranet
20
Machine Hanging at AR logo
Flash Rom not seated properly
Remove and Re-seat Flash rom or Re-
flash
Sharp Electronics (UK)Ltd., Technical Services Group
Symptom
Cause
Action
9
Paper jam at FPID when using FN1
Paper exiting copier is ‘bowed’ by the
exit rollers
Remove the pressure springs on the exit
rollers as per installation instructions for
FN2.
10
Locating pins for FN2 front frame side
cannot be screwed in
Either the thread in the hole is missing
or it has been damaged during
removal of the knock out panel
Use the supplied self tap screw to cut the
thread first
11
PFID jam
Paper catches and jams when using
the short path in FN-1
Adjust the position of the short path gate
solenoid.
12
Unable to staple in covers mode when
using FN2
Bypass disabled for use with lower
tray
Reset facility in key op mode
13
Shows paper size as extra when
using bypass
Bypass sensors not set up
Set-up size sensors in SIM 40
14
High noise level from fans in standby
mode
Vibration from ICU board area
Fit modified parts as per FastFax 072
15
‘Bar coded copies’
Main corona grid to tight
Check grid tension is to guide marks
16
Intermittent trail edge blanking
Main corona rear frame end block
cracked
Replace end block
17
Simulation 26-35
Set code to ‘any’ to allow all trouble
history to be recorded
18
Image shift in staple mode on FN-1
Simulation 50
Image alignment must be set-up
accurately in simulation 50, to allow
easier set up enter simulation then close
the screen this will allow Black & White
reverse and staple mode to be selected,
press the area highlighted ‘TEST’
19
Jam Map (22-3)
Abbreviations
A full breakdown of abbreviations is
available on the intranet
20
Machine Hanging at AR logo
Flash Rom not seated properly
Remove and Re-seat Flash rom or Re-
flash
Sharp Electronics (UK)Ltd., Technical Services Group
Symptom
Cause
Action
9
Paper jam at FPID when using FN1
Paper exiting copier is ‘bowed’ by the
exit rollers
Remove the pressure springs on the exit
rollers as per installation instructions for
FN2.
10
Locating pins for FN2 front frame side
cannot be screwed in
Either the thread in the hole is missing
or it has been damaged during
removal of the knock out panel
Use the supplied self tap screw to cut the
thread first
11
PFID jam
Paper catches and jams when using
the short path in FN-1
Adjust the position of the short path gate
solenoid.
12
Unable to staple in covers mode when
using FN2
Bypass disabled for use with lower
tray
Reset facility in key op mode
13
Shows paper size as extra when
using bypass
Bypass sensors not set up
Set-up size sensors in SIM 40
14
High noise level from fans in standby
mode
Vibration from ICU board area
Fit modified parts as per FastFax 072
15
‘Bar coded copies’
Main corona grid to tight
Check grid tension is to guide marks
16
Intermittent trail edge blanking
Main corona rear frame end block
cracked
Replace end block
17
Simulation 26-35
Set code to ‘any’ to allow all trouble
history to be recorded
18
Image shift in staple mode on FN-1
Simulation 50
Image alignment must be set-up
accurately in simulation 50, to allow
easier set up enter simulation then close
the screen this will allow Black & White
reverse and staple mode to be selected,
press the area highlighted ‘TEST’
19
Jam Map (22-3)
Abbreviations
A full breakdown of abbreviations is
available on the intranet
20
Machine Hanging at AR logo
Flash Rom not seated properly
Remove and Re-seat Flash rom or Re-
flash
Sharp Electronics (UK)Ltd., Technical Services Group
Symptom
Cause
Action
9
Paper jam at FPID when using FN1
Paper exiting copier is ‘bowed’ by the
exit rollers
Remove the pressure springs on the exit
rollers as per installation instructions for
FN2.
10
Locating pins for FN2 front frame side
cannot be screwed in
Either the thread in the hole is missing
or it has been damaged during
removal of the knock out panel
Use the supplied self tap screw to cut the
thread first
11
PFID jam
Paper catches and jams when using
the short path in FN-1
Adjust the position of the short path gate
solenoid.
12
Unable to staple in covers mode when
using FN2
Bypass disabled for use with lower
tray
Reset facility in key op mode
13
Shows paper size as extra when
using bypass
Bypass sensors not set up
Set-up size sensors in SIM 40
14
High noise level from fans in standby
mode
Vibration from ICU board area
Fit modified parts as per FastFax 072
15
‘Bar coded copies’
Main corona grid to tight
Check grid tension is to guide marks
16
Intermittent trail edge blanking
Main corona rear frame end block
cracked
Replace end block
17
Simulation 26-35
Set code to ‘any’ to allow all trouble
history to be recorded
18
Image shift in staple mode on FN-1
Simulation 50
Image alignment must be set-up
accurately in simulation 50, to allow
easier set up enter simulation then close
the screen this will allow Black & White
reverse and staple mode to be selected,
press the area highlighted ‘TEST’
19
Jam Map (22-3)
Abbreviations
A full breakdown of abbreviations is
available on the intranet
20
Machine Hanging at AR logo
Flash Rom not seated properly
Remove and Re-seat Flash rom or Re-
flash
Sharp Electronics (UK)Ltd., Technical Services Group
Display

Sharp AR-285 (serv.man167) Service Manual / Technical Bulletin ▷ Download

  • DOWNLOAD Sharp AR-285 (serv.man167) Service Manual ↓ Size: 49.96 KB | Pages: 2 in PDF or view online for FREE
  • Here you can View online or download the Service Manual / Technical Bulletin for the Sharp AR-285 (serv.man167) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp AR-285 (serv.man167) Copying Equipment. Information contained in Sharp AR-285 (serv.man167) Service Manual / Technical Bulletin (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.