Sharp AR-280 (serv.man35) User Manual / Operation Manual ▷ View online
4-5
CHAPTER
4
The message “
(TONER SUPPLY IS LOW. PRESS
FOR
GUIDANCE.)
” will appear in the message display before the toner
supply is completely empty. If copying is continued, copies will
gradually become lighter until the copier stops and the message
display changes to “
gradually become lighter until the copier stops and the message
display changes to “
ADD TONER. PRESS
FOR GUIDANCE.
”
indicating that the toner supply is empty. Toner can be added any time
after the message “
after the message “
(TONER SUPPLY IS LOW. PRESS
FOR
GUIDANCE.)
” appears. To add toner, stop the copier and proceed as
below. When either message appears, you can use the INFORMATION
(
(
) key for detailed information as necessary.
During long copy runs of multiple originals containing many images
and/or dark shades, “
and/or dark shades, “
TONER REPLENISHMENT IN PROGRESS.
” will
appear and the copier will stop making copies even though toner is
left.
The copier will automatically cycle and replenish the toner to the
normal level and then the START (
left.
The copier will automatically cycle and replenish the toner to the
normal level and then the START (
) key indicator will light up. Press
the START (
) key to resume copying.
SUPPLIES
Adding toner
ADDING TONER
For best copying results, be sure to use
only Sharp products. The package of
Sharp toner has the Genuine Supplies
label.
only Sharp products. The package of
Sharp toner has the Genuine Supplies
label.
1
Open the front cover.
2
Pull down the toner hopper lock lever and pull the toner
hopper out slowly until it stops.
hopper out slowly until it stops.
3
Tap on the top of the toner cartridge 5 times. Hold the
new toner cartridge vertically and vigorously shake it
up and down about 20 times, then invert the cartridge
and again shake it up and down about 20 times. This will
loosen the toner and allow it to flow more easily into the
toner hopper.
new toner cartridge vertically and vigorously shake it
up and down about 20 times, then invert the cartridge
and again shake it up and down about 20 times. This will
loosen the toner and allow it to flow more easily into the
toner hopper.
GENUINE SUPPLIES
20 x
5 x
4-6
CHAPTER
4
4
Place the new toner cartridge with the tabs in the
notches as shown.
notches as shown.
5
Slide the toner cartridge along the guides over the toner
hopper.
hopper.
6
Hold the toner cartridge with one hand while pulling on
the sealing tape to remove it.
the sealing tape to remove it.
7
Tap on the top of the toner cartridge 5 times to start the
flow of toner into the toner hopper.
flow of toner into the toner hopper.
●
If the toner cartridge was sufficiently shaken as described in
step 3, it will take about 50 seconds for the cartridge to empty.
Do not remove the cartridge until it is empty. If not empty, tap on
the top of the cartridge again until empty.
step 3, it will take about 50 seconds for the cartridge to empty.
Do not remove the cartridge until it is empty. If not empty, tap on
the top of the cartridge again until empty.
8
Slide the empty toner cartridge back along the guides
and remove it.
and remove it.
●
The cartridge opening will be closed as it is moved back along
the guides.
the guides.
9
Slide the toner hopper into the copier and return the
toner hopper lock lever into place.
toner hopper lock lever into place.
10
Close the front cover.
NOTE:
Add only one cartridge of toner.
Add only one cartridge of toner.
ADDING TONER
SUPPLIES
Adding toner
Sealing tape
4-7
CHAPTER
4
1
Open the toner collecting container cover.
●
Push once on the door to unlatch and open it.
2
Disengage and remove the container from the copier.
●
Toner cannot be reused. Do not transfer used toner to the toner
hopper.
hopper.
●
Remove the cap from a new toner collecting container and use
it to cover the full toner collecting container.
it to cover the full toner collecting container.
●
Keep the full toner collecting container until the next regular
service call. Your authorised Sharp Service Technician will
collect the container for disposal.
service call. Your authorised Sharp Service Technician will
collect the container for disposal.
3
Install a new toner collecting container until it clicks into
place.
place.
4
Close the toner collecting container cover.
USED TONER DISPOSAL
“
REPLACE USED TONER CONTAINER. PRESS
FOR GUIDANCE.
”
will appear when the toner collecting container is full.
The copier will stop and will not operate until a new container has been
installed. Replace the toner collecting container as described below.
When the above message is displayed, you can use the INFORMATION
(
The copier will stop and will not operate until a new container has been
installed. Replace the toner collecting container as described below.
When the above message is displayed, you can use the INFORMATION
(
) key for detailed information as necessary.
SUPPLIES
Used toner disposal
4-8
CHAPTER
4
SUPPLIES
Storage of supplies
GENUINE SUPPLIES
STORAGE OF SUPPLIES
The supplies of this copier replaced by the user include copy paper,
toner, toner collecting container, and staple cartridges for an optional
finisher (AR-FN1).
toner, toner collecting container, and staple cartridges for an optional
finisher (AR-FN1).
For best copying results, be sure to use
only Sharp products. The package of
Sharp toner has the Genuine Supplies
label.
only Sharp products. The package of
Sharp toner has the Genuine Supplies
label.
Photoconductive drum
The AR-280/AR-285/AR-335 Copiers have advanced process control
technology which improves copy quality uniformity. This feature
stabilizes copy quality throughout the life of the photoconductive
drum by automatically compensating for the changes in drum
characteristics due to wear, operator use patterns, and environmental
conditions. The automatic adjustments are made in response to a
sensor that detects the reflectance characteristics of the drum.
technology which improves copy quality uniformity. This feature
stabilizes copy quality throughout the life of the photoconductive
drum by automatically compensating for the changes in drum
characteristics due to wear, operator use patterns, and environmental
conditions. The automatic adjustments are made in response to a
sensor that detects the reflectance characteristics of the drum.
WARNING
This feature requires drums containing the special reflectance area
(recommended Sharp genuine photoconductive drum), to prevent
low image density copies from poor process control and possible
damage to the machine. If you use other drums, the process control
system cannot run properly.
(recommended Sharp genuine photoconductive drum), to prevent
low image density copies from poor process control and possible
damage to the machine. If you use other drums, the process control
system cannot run properly.
Proper storage
1
Store the supplies in a location that is:
●
clean and dry,
●
at a stable temperature,
●
not exposed to direct sunlight.
2
Store copy paper in the wrapper and lying flat.
●
Paper stored in packages standing up or out of the wrapper may
curl or become damp, resulting in paper misfeeds.
curl or become damp, resulting in paper misfeeds.
Click on the first or last page to see other AR-280 (serv.man35) service manuals if exist.