Sharp AR-206 (serv.man4) Service Manual ▷ View online
Main
code
code
Sub
code
Contents
Details of operation
Initial
value
value
Set range
41
3
Document sensor light
reception level display
reception level display
<Other than AR-162>
Used to display the light reception level and the detection level of the
document sensor. (The sensor level adjusted with SIM 41-2 is displayed.)
document sensor. (The sensor level adjusted with SIM 41-2 is displayed.)
42
1
Developing counter clear
Used to clear the Developing counter.
∗
2
43
1
Fusing temperature setting
Used to display the current setting of the fusing temperature at right.
After selecting the fusing temperature with the magnification ratio display
key, press the start key, and the set value is stored. The set range is
155
After selecting the fusing temperature with the magnification ratio display
key, press the start key, and the set value is stored. The set range is
155
∼
190˚C. Use the magnification ratio key to adjust the value by –5˚C.
170
155
∼
190
46
1
Copy density level
adjustment
adjustment
After completion of warmup, shading is performed and the currently set
copy density level is displayed. For the adjustment procedure, refer to
the previous descriptions.
copy density level is displayed. For the adjustment procedure, refer to
the previous descriptions.
48
1
∼
99
19
AE mode picture quality
change
change
The currently set AE picture quality mode (gamma table) is displayed
with the following set values. Enter a set value and press the START
key, then the set value will be inputted.
with the following set values. Enter a set value and press the START
key, then the set value will be inputted.
1
1
∼
2
48
1
Main scanning (front/rear)
direction magnification
ratio adjustment
(Copy/FAX/OC-SPF
common)
direction magnification
ratio adjustment
(Copy/FAX/OC-SPF
common)
After completion of warmup, shading is performed and the currently set
main scanning (front/rear) direction magnification ratio adjustment and
the OC mode document center off adjustment are performed. For the
adjustment procedure, refer to the previous descriptions.
main scanning (front/rear) direction magnification ratio adjustment and
the OC mode document center off adjustment are performed. For the
adjustment procedure, refer to the previous descriptions.
58
1
∼
99
2
OC mode sub scanning
direction magnification
ratio adjustment in
copying
direction magnification
ratio adjustment in
copying
After completion of warmup, shading is performed and the currently set
OC mode sub scanning direction magnification ratio adjustment in
copying is performed. For the adjustment procedure, refer to the
previous descriptions.
OC mode sub scanning direction magnification ratio adjustment in
copying is performed. For the adjustment procedure, refer to the
previous descriptions.
50
1
∼
99
∗
2: Display after clearing each counter
000 (0.75 sec)
→
Blank (0.35 sec)
→
000 (0.75 sec)
→
Blank (1.0 sec)
→
Repetition
Key operation
Display
Light reception/Detection
level select: Magnification
ratio display key
level select: Magnification
ratio display key
Display at the 3rd digit
“A”:
“A”:
Light reception level display
“b”:
Document detection level display
Sensor select: Auto
magnification ratio select key
magnification ratio select key
Sensor A: A3 (11
×
17) document
size LED
Sensor B: A4 (8 1/2
Sensor B: A4 (8 1/2
×
14) document
size LED
Sensor C: A4R (8 1/2
Sensor C: A4R (8 1/2
×
11)
document size LED
Sensor D: B4 (8 1/2
Sensor D: B4 (8 1/2
×
5 1/2)
document size LED
Key operation
Fusing temperature select: Magnification ratio display key
Key operation
Display
Mode select:
Exposure mode select
key
Copy density level:
Copy quantity keys
Exposure mode select
key
Copy density level:
Copy quantity keys
<LED lighting at each mode selection>
Auto mode: AUTO LED
Manual mode: MANUAL LED
Photo mode: PHOTO LED
Toner save mode: MANUAL + PHOTO LED
AETS mode: AUTO + PHOTO LED
Key operation/Display
1: Picture quality priority mode
2: Toner consumption priority mode
Key operation
Display
Adjustment mode
select: Magnification
ratio display key
select: Magnification
ratio display key
Auto magnification ratio adjustment:
AUTO
AUTO
LED
Manual main scanning
direction magnification
ratio adjustment
Set value: Copy
quantity keys
direction magnification
ratio adjustment
Set value: Copy
quantity keys
Manual magnification ratio adjustment:
MANUAL
MANUAL
LED
OC mode document center off adjustment:
PHOTO
PHOTO
LED
Key operation
OC mode sub scanning direction magnification ratio in copying:
Copy quantity keys
Copy quantity keys
AR-162 SIMULATIONS – 10
Main
code
code
Sub
code
Contents
Details of operation
Initial
value
value
Set range
48
5
SPF mode sub scanning
direction magnification
ratio adjustment in
copying
direction magnification
ratio adjustment in
copying
<Only when an
SPF/RSPF is installed>
SPF/RSPF is installed>
After completion of warmup, shading is performed and the currently set
SPF mode sub scanning direction magnification ratio adjustment in
copying is performed. For the adjustment procedure, refer to the
previous descriptions.
SPF mode sub scanning direction magnification ratio adjustment in
copying is performed. For the adjustment procedure, refer to the
previous descriptions.
33
45
1
∼
99
50
1
Copy image position
adjustment
adjustment
After completion of warmup, shading is performed and the currently set
value is displayed. For the adjustment procedure, refer to the previous
descriptions.
value is displayed. For the adjustment procedure, refer to the previous
descriptions.
55
77
77
18
48
40
18
40
18
18
20
55
60
60
60
1
∼
99
10
Paper off center
adjustment
adjustment
After completion of warmup, shading is performed and the currently set
off center adjustment of each paper feed port is displayed. For the
adjustment procedure, refer to the previous descriptions.
off center adjustment of each paper feed port is displayed. For the
adjustment procedure, refer to the previous descriptions.
50
1
∼
99
13
OC mode document off
center adjustment
center adjustment
After completion of warmup, shading is performed and the currently set
off center adjustment value for the document in OC reading is displayed.
For the adjustment procedure, refer to the previous descriptions.
off center adjustment value for the document in OC reading is displayed.
For the adjustment procedure, refer to the previous descriptions.
50
1
∼
99
16
SPF mode document off
center adjustment
center adjustment
<Only when an
SPF/RSPF is installed>
SPF/RSPF is installed>
After completion of warmup, shading is performed and the currently set
off center adjustment value for the document in SPF reading is
displayed. For the adjustment procedure, refer to the previous
descriptions.
off center adjustment value for the document in SPF reading is
displayed. For the adjustment procedure, refer to the previous
descriptions.
61
1
∼
99
Key operation
Display
Adjustment mode select:
Exposure mode select key
Exposure mode select key
Auto: SPF mode sub scanning
direction magnification ratio in copying
direction magnification ratio in copying
Set value:
Copy quantity keys
Copy quantity keys
Manual: RSPF mode sub scanning
direction magnification ratio in copying
direction magnification ratio in copying
Key operation
Display
Adjustment mode
select:
Exposure
select:
Exposure
mode
select
key
Set value:
Copy quantity keys
Copy quantity keys
Auto: Copy lead edge adjustment
Manual: SPF lead edge adjustment
<Not used>
Photo: Main cassette lead edge void
adjustment
Auto + Manual: Left edge void adjustment
Auto + Photo: Rear edge void adjustment
Auto + Manual + Photo: Option cassette
lead edge void adjustment
Manual + Photo: Multi bypass tray lead
edge void adjustment
None: Duplex lead edge void adjustment
<Only AR-206/207>
Exposure 1: Print start position adjustment
Exposure 3: Duplex lead edge adjustment
<Only AR-206/207>
Exposure 5: Duplex rear edge void
adjustment <Only AR-206/207>
Manual: SPF lead edge adjustment
<Not used>
Photo: Main cassette lead edge void
adjustment
Auto + Manual: Left edge void adjustment
Auto + Photo: Rear edge void adjustment
Auto + Manual + Photo: Option cassette
lead edge void adjustment
Manual + Photo: Multi bypass tray lead
edge void adjustment
None: Duplex lead edge void adjustment
<Only AR-206/207>
Exposure 1: Print start position adjustment
Exposure 3: Duplex lead edge adjustment
<Only AR-206/207>
Exposure 5: Duplex rear edge void
adjustment <Only AR-206/207>
Key operation
Display
Paper feed port tray
select: Tray select key
select: Tray select key
Main cassette:
Main cassette select LED
Main cassette select LED
Off center adjustment
value: numeric keys
value: numeric keys
Manual paper feed:
Manual feed select LED
Manual feed select LED
No. 2 cassette:
No. 2 cassette select LED
No. 2 cassette select LED
No. 3 cassette:
No. 3 cassette select LED
<Only when an option is installed>
No. 3 cassette select LED
<Only when an option is installed>
No. 4 cassette:
No. 4 cassette select LED
<Only when an option is installed>
No. 4 cassette select LED
<Only when an option is installed>
Duplex: None <Only AR-206/207>
Key operation
Off center adjustment value: Copy quantity keys
Key operation
Off center adjustment value: Copy quantity keys
AR-162 SIMULATIONS – 11
Main
code
code
Sub
code
Contents
Details of operation
Initial
value
value
Set range
50
18
Duplex memory reverse
position adjustment
position adjustment
<Only when an duplex
function is installed>
function is installed>
After completion of warmup, shading is performed and currently set
value is displayed
value is displayed
58
1
∼
99
50
19
Duplex rear edge void
adjustment
adjustment
<Only when an duplex
function is installed>
function is installed>
After completion of warmup, shading is performed and currently set
value is displayed.
value is displayed.
37
52
70
70
1
∼
99
51
2
Resist amount adjustment
After completion of warmup, shading is performed and the currently set
resist amount adjustment value is displayed.
resist amount adjustment value is displayed.
50
1
50
50
48
50
48
1
∼
99
(6
∼
94 for
the duplex
only)
63
1
Shading data check
The copy lamp is shifted to the shading position and it is lighted with the
reference voltage at AD conversion fixed (Vref– = 0.5V, Vref+ = 4.5V).
The level of one pixel at the center at that time is displayed.
reference voltage at AD conversion fixed (Vref– = 0.5V, Vref+ = 4.5V).
The level of one pixel at the center at that time is displayed.
64
1
Self print mode
Disregards the optical system and performs self printing in 1 by 2mode.
67
14
Printer Flash ROM
Data Download
<Only when printer
function is installed>
Data Download
<Only when printer
function is installed>
The machine enters the version up mode of the printer control PWB
flash ROM.
For details, refer to the later.
flash ROM.
For details, refer to the later.
Key operation
Memory reverse position adjustment value:
Copy quantity keys
Copy quantity keys
Key operation
Display
Adjustment mode select:
Exposure mode select key
Exposure mode select key
Auto: SPF/R-SPF rear edge void
Set value:
Copy quantity keys
Copy quantity keys
Manual: R-SPF off center
Photo: R-SPF lead edge void
Photo: R-SPF lead edge void
Key operation
Display
Resist amount adjustment:
Copy quantity keys
Adjustment mode select:
Exposure mode select key
Copy quantity keys
Adjustment mode select:
Exposure mode select key
Auto: Main cassette
Manual: 2nd tray
Photo: Manual feed tray
Auto + Manual: Duplex <Only AR-206/207>
Auto + Photo: RSPF <Only when an
option is installed>
Manual: 2nd tray
Photo: Manual feed tray
Auto + Manual: Duplex <Only AR-206/207>
Auto + Photo: RSPF <Only when an
option is installed>
Display
Display section: Shading data
AR-162 SIMULATIONS – 12
[8] USER PROGRAMS
The user programs allow the parameters of certain functions to be set, changed, or canceled as desired.
1. List of user programs
This copier has the following user programs.
Program name
Program
No
Description
Default
Parameters
Auto clear time
1
Sets the auto clear time. The copier returns to the initial settings
when the auto clear time elapses after the last copy is made.
when the auto clear time elapses after the last copy is made.
60sec
0(OFF)
1(30sec)
2(60sec)
3(90sec)
4(120sec)
5(10sec)
Preheat mode
2
Sets the time that elapses before the copier enters the preheat
mode after any operation is made.
mode after any operation is made.
90sec
0(OFF)
1(30sec)
2(60sec)
3(90sec)
4(120sec)
Auto power shut-
off timer
off timer
3
Sets the time that elapses before the copier enters the auto
power shut-off mode after any operation is made.
power shut-off mode after any operation is made.
30min
1(30min)
2(60min)
3(90min)
4(120min)
5(240min)
Stream feeding
mode*
mode*
4
Enables or disables the stream feeding mode when an optional
SPF or RSPF is installed.
SPF or RSPF is installed.
OFF
0(OFF)
1(ON)
Auto power shut-
off setting
off setting
5
Enables or disables the auto power shut-off mode.
ON
0(OFF)
1(ON)
Border line for 2
in 1 or 4 in 1*
in 1 or 4 in 1*
6
Enables or disables the border line which is printed in 2 in 1 or 4
in 1 copying when an electronic sorting kit and an SPF or RSPF
are installed.
in 1 copying when an electronic sorting kit and an SPF or RSPF
are installed.
OFF
0(OFF)
1(ON)
Rotation copy*
7
Enables or disables rotation of original images.
ON
0(OFF)
1(ON)
Auto paper
select mode
select mode
8
Enables or disables the auto paper selection.
ON
0(OFF)
1(ON)
Auto tray
switching
switching
9
Enables or disables the automatic tray switching which occurs
when paper in a tray runs out. (This switching cannot switch to
the bypass tray.)
when paper in a tray runs out. (This switching cannot switch to
the bypass tray.)
ON
0(OFF)
1(ON)
Auditing mode
10
Enables or disables the auditing mode, which controls access to
copier.
copier.
OFF
0 (OFF)
1 (ON)
Account number
entry
entry
11
Registers accounts for auditing mode.
–
–
Account number
change
change
12
Changes account numbers for auditing mode.
–
–
Account number
deletion
deletion
13
Deletes accounts for auditing mode.
–
–
Number of
copies per
account
copies per
account
14
Displays the total number of copies made against account
numbers.
numbers.
–
–
Resetting account
15
Resets all audit accounts or resets any desired individual account.
–
–
Erase width
adjustment*
adjustment*
16
Sets the amount of the edge erase and center erase areas.
10mm[1/2"]
0(0mm[0"])
1(5mm[1/4"])
2(10mm[1/2"])
3(15mm[3/4"])
4(20mm[1"])
AR-162 USER PROGRAMS – 1
Click on the first or last page to see other AR-206 (serv.man4) service manuals if exist.