AR-122E (serv.man56). Sect. 5 Maintenance — Sharp Copying Equipment User Guide / Operation Manual

Model
AR-122E (serv.man56)
Pages
5 Few pages! See other manuals at the bottom of the first or last page.
Size
272.67 KB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
Copying Equipment / Sect. 5 Maintenance
File
ar-122e-sm56.pdf
Date

View Sharp AR-122E (serv.man56) User Guide / Operation Manual online

21
5
This chapter describes how to replace the toner cartridge and how to clean unit.
TONER CARTRIDGE REPLACEMENT
When the toner cartridge replacement required (
) indicator lights up, replacement 
of the toner cartridge will be needed soon. Obtain a new cartridge. When the toner 
cartridge replacement required (
) indicator blinks, the toner cartridge must be 
replaced before copying can be resumed. Replace the toner cartridge by following 
the procedure below.
1
Open the side cover while 
pressing the side cover open 
button.
2
Push gently on both sides of 
the front cover to open the 
cover.
Be sure to use only genuine SHARP parts and supplies.
For best copying results, be sure to use only SHARP Genuine 
Supplies which are designed, engineered, and tested to maximise the 
life and performance of SHARP copiers. Look for the Genuine 
Supplies label on the toner package.
During long copy run of a dark original, the start (
) indicator may 
blink, the indicator light up, and the unit stop, even though toner is left. 
The unit will feed toner up to 2 minutes and then the start (
) indicator 
will light up. Press the start (
) key to restart copying.
5
MAINTENANCE
22
3
Gently pull the toner cartridge 
out while pressing the lock 
release lever.
4
Remove the toner cartridge from the bag. Grasp the cartridge 
on both sides and shake it horizontally four or five times. After 
shaking the cartridge, remove the toner seal.
5
Gently insert the toner cartridge along 
the guides until it locks in place while 
pushing the lock release lever. 
Remove the tape from the shutter. Pull 
the shutter out of the toner cartridge 
as shown in the illustration. Discard 
the shutter.
• After removing the toner cartridge, do not shake it or tap on it. Doing 
so may cause toner to leak from the cartridge. Put the old cartridge 
immediately in the bag contained in the box of the new cartridge. 
• Dispose of the old toner cartridge in accordance with local regulations.
Grasp the toner cartridge as shown in the illustration. Do not hold the 
cartridge by the shutter. Be sure to only shake the cartridge before the 
toner seal is removed.
Toner cartridge lock 
release lever
4 or 5 times
Shutter
Toner seal
4 or 5 times
Shutter
Toner seal
23
5
6
Close the front cover and 
then the side cover by 
pressing the round 
projections near the side 
cover open button. The 
indicator will go out and the 
start (
) indicator will light 
up.
TONER CARTRIDGE LIFE
To find out the approximate quantity of toner remaining, follow the procedure 
described below.
1
Press and hold down the light (
) and dark (
) keys 
simultaneously for more than 5 seconds until all the alarm 
indicators (
)  blink and  "
" appears in the 
display.
2
Press and hold down the copy ratio display 
(%) 
key for more thn 
5 seconds.
The approximate quantity of toner remaining will be indicated in the display 
as a percentage ("100", "75", "50", "25" or "10" is displayed). When the 
percentage is less than 10%, 
(
will be displayed.
3
Press the light (
) or dark (
) key.
All alarm indicators wil go out.
When closing the covers, 
be sure to close the front 
cover securely and then 
close the side cover. If the 
covers are closed in the 
wrong order, the covers 
may be damaged.
Even after a new toner cartridge is installed, the start (
) indicator 
may not light up, indicating copying cannot be restarted (toner is not 
sufficiently fed). In this case, open and close the side cover. The 
copier will feed toner again approximately 2 minutes and then 
copying can be restarted.
24
CLEANING THE UNIT
Proper care is essential in order to get clean, sharp copies. Be sure to take a few 
minutes to regularly clean the unit.
Cabinet
Wipe the cabinet with a soft, clean cloth.
Original table and the back side of the original cover
Stains on the glass or cover will also be copied. Wipe the glass and cover with a soft, 
clean cloth. If necessary, dampen the cloth with a glass cleaner.
• Before cleaning, be sure to turn the power switch off and remove the 
power cord from the outlet.
• Do not use thinner, benzene or other volatile cleaning agents. Doing 
so may cause deformation, discoloration, deterioration or malfunction.
Original table
Original cover
Page of 5
Display

Download Sharp AR-122E (serv.man56) User Guide / Operation Manual

Here you can view online or download Sharp AR-122E (serv.man56) User Guide / Operation Manual in pdf. This User Guide / Operation Manual can help you recover, restore, fix, disassemble and repair Sharp AR-122E (serv.man56) Copying Equipment. Information contained in Sharp AR-122E (serv.man56) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).