Sharp AL-1457D (serv.man6) Service Manual ▷ View online
AL-1218/1458 DUPLEX-RELATED ITEMS 2 - 4
5. List of simulations
Sim
No.
Kind of
main code
Sub
code
Operation
01
Optical system
01
Mirror scan operation
06
Aging of mirror scanning
02
SPF Individual
load operation
load operation
02
SPF sensor status display
03
Motor ON
04
Paper feed solenoid ON
05
Lamp ON check
01
Operation panel display check
02
Fusing lamp, cooling fan operation
check
check
03
Copy lamp ON
06
Machine
individual load
operation
individual load
operation
01
Paper feed solenoid ON
02
Resist solenoid ON
07
Aging
01
Warm-up display and aging with jam
06
Intermittent aging
08
High voltage
output check
output check
01
Developing bias
02
Main charger (Grid high)
03
Grid voltage (Low)
06
Transfer charger
10
Other
None Toner motor aging
14
Trouble reset
None Cancel of troubles other than U2
16
U2 trouble reset
None Cancel of U2 trouble
22
Counter display
04
JAM total counter display
05
Total counter display
08
SPF counter display
12
Drum counter display
14
P-ROM version display
17
Copy counter display
18
Printer counter display
19
Scanner mode counter display
21
Scanner counter display
22
SPF JAM counter display
24
Special counter
clear
clear
01
JAM total counter clear
04
SPF counter clear
07
Drum counter clear
08
Copy counter clear
09
Printer counter clear
13
Scanner counter clear
14
SPF JAM total counter clear
15
Scanner mode counter clear
25
Main motor ON
01
Main motor operation check (Cooling
fan motor rotation check)
fan motor rotation check)
10
Polygon motor ON
Sim
No.
Kind of
main code
Sub
code
Operation
26
Various setup
01
Manual feed setup
02
(R) SPF setup
03
Second cassette setup
04
Machine duplex setup
06
Destination setup
07
Machine conditions check
20
Rear edge void setup
30
CE mark support control ON/OFF
38
Cancel of stop at drum life over
39
Memory capacity check
40
Polygon motor OFF time setup
(Time required for turning OFF after
completion of printing)
(Time required for turning OFF after
completion of printing)
42
Transfer ON timing control setup
43
Side void setup
44
SPF document rear edge read setup
62
Energy-save mode copy lamp setup
63
Fan control select setup
30
Sensor operation
check (Standard
provision)
check (Standard
provision)
01
Paper sensor status display
43
Fusing
temperature
setup
temperature
setup
01
Fusing temperature setup (Normal
copy)
copy)
04
Fusing temperature setup 2
05
Fusing temperature setup in duplex
copy
copy
09
Setup of fusing control of postcard
size paper
size paper
46
Exposure
adjustment
adjustment
01
Copy density adjustment (300dpi)
02
Copy density adjustment (600dpi)
18
Image contrast adjustment (300dpi)
19
γ
table setup or AE operation mode
setup
20
SPF exposure correction
29
Image contrast adjustment (600dpi)
31
Image sharpness adjustment
32
Copier color reproduction setup
48
Magnification
ratio correction
ratio correction
01
Front/rear (main scanning) direction
and scan (sub scanning) direction
magnification ratio adjustment
and scan (sub scanning) direction
magnification ratio adjustment
49
01
Flash ROM program writing mode
50
Lead edge
adjustment
adjustment
01
Lead edge image position
10
Center offset adjustment
18
Memory reverse position adjustment
in duplex copy
in duplex copy
19
Duplex copy rear edge void
adjustment
adjustment
51
Timing
adjustment
adjustment
02
Resist quantity adjustment
53
08
SPF scan position automatic
adjustment
adjustment
61
Laser system
operation
operation
03
Polygon motor check
(HSYNC output check)
(HSYNC output check)
63
Shading
01
Shading check
64
Self print
01
Self print
AL-1218/1458 DUPLEX-RELATED ITEMS 2 - 5
6. Contents of simulations
Input method: Clear key
→
Exposure Select key
→
Clear key
→
Exposure Select key
Main
code
code
Sub
code
Content
50
18
Memory reverse position adjustment in duplex copy
When this simulation is executed, the current setup value of correction is displayed. Enter the correction value with the 10-key and
press the PRINT switch, and the entered value will be saved. (Correction value 1 – 99, correction zero = 0, or 50) When the correction
value is set to 0, the correction value is written as 50.
Front surface printing in the S-D mode and printing on even pages in the D-S mode are reverse memory copy operations from the
document rear edge section.
When, therefore, the output image print position adjustment is required, adjust as follows:
In the reverse memory copy operation, if the document scan direction is in the direction of the arrow in the figure, the scan rear edge
section of the image is printed first.
When, therefore, the print lead edge is shifted, set the reference chart so that the reference position is in the rear edge section, and use
this simulation to adjust so that the print image lead edge comes to the lead edge.
Since printing is performed by processing the scanned image from the scan end position to the scan lead edge, the print lead edge
position adjustment is performed by changing the end data position stored in memory with the simulation setup value.
When this simulation is executed, the current setup value of correction is displayed. Enter the correction value with the 10-key and
press the PRINT switch, and the entered value will be saved. (Correction value 1 – 99, correction zero = 0, or 50) When the correction
value is set to 0, the correction value is written as 50.
Front surface printing in the S-D mode and printing on even pages in the D-S mode are reverse memory copy operations from the
document rear edge section.
When, therefore, the output image print position adjustment is required, adjust as follows:
In the reverse memory copy operation, if the document scan direction is in the direction of the arrow in the figure, the scan rear edge
section of the image is printed first.
When, therefore, the print lead edge is shifted, set the reference chart so that the reference position is in the rear edge section, and use
this simulation to adjust so that the print image lead edge comes to the lead edge.
Since printing is performed by processing the scanned image from the scan end position to the scan lead edge, the print lead edge
position adjustment is performed by changing the end data position stored in memory with the simulation setup value.
19
Duplex copy rear edge void adjustment
Used to adjust the rear edge void quantity in duplex copy.
(Operating procedure)
When this simulation is executed, the current setup value is displayed the current setup value is displayed in two digits. (Center value:
50 However, setup 50 = setup 0) When the correction value is set to 0, the correction value is written as 50. Press the copy mode select
key to select your desired copy mode, and the display will change. Enter the adjustment value with the 10-key and press the PRINT
switch, and the setup value will be saved and a copy will be made. (The paper information is cleared for every copying.) Press the clear
key to save the setup value and exit from the simulation mode. (Increasing the setup value by 1 increases the void quantity by about
0.1mm.)
Used to adjust the rear edge void quantity in duplex copy.
(Operating procedure)
When this simulation is executed, the current setup value is displayed the current setup value is displayed in two digits. (Center value:
50 However, setup 50 = setup 0) When the correction value is set to 0, the correction value is written as 50. Press the copy mode select
key to select your desired copy mode, and the display will change. Enter the adjustment value with the 10-key and press the PRINT
switch, and the setup value will be saved and a copy will be made. (The paper information is cleared for every copying.) Press the clear
key to save the setup value and exit from the simulation mode. (Increasing the setup value by 1 increases the void quantity by about
0.1mm.)
Print lead edge
Lead edge void (1)
Print start position
Lead edge void (1)
Print start position
Rear edge void
Print rear edge
Print rear edge
Document transport direction
Scan lead edge
Scan end position
(Default: Scan cut by void (1))
(Default: Scan cut by void (1))
Scan direction
Scan rear edge
Paper transport direction
Adjustment mode
Lamp ON
Paper rear edge void quantity
TEXT lamp
Print start position (Duplex back)
PHOTO lamp
Memo
q
PARTS GUIDE
CONTENTS
Because parts marked with "
!" is indispensable for the machine safety maintenance and poeration, it must
Be replaced with the parts specific to the product specification.
SHARP CORPORATION
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
after sales service only.
The contents are subject to change without notice.
CODE:00ZAL1458//P1
DIGITAL LASER COPIER /
DIGITAL MULTIFUNCTIONAL SYSTEM
AL-1218
MODEL
AL-1458
(For Europe)
(AL-1458)
1
Exteriors
3
SPF exteriors (AL-1458)
5
SPF pick up unit (AL-1458)
6
Operation panel
7
Side door unit
8
Optical frame
F
Delivery paper guide unit
G
Middle frame
H
Base plate unit 1
I
Base plate unit 2
J
Fusing unit
K
Drive unit
N
Single manual paper feeding unit
(AL-1218)
O
Multi manual paper feeding unit
(AL-1458)
R
250 sheets tray
S
Harness
T
Packing material & accessories
U
Operation PWB
V
MCU PWB
X
DC power supply PWB
■
Index
The AL-1218/AL-1458 Parts Guide describes only changed from AL-1217/AL-1457 Parts Guide.
For the common parts, please refer to the AL-1217/AL-1457 Parts Guide (Code: 00ZAL1457//P1)
For the common parts, please refer to the AL-1217/AL-1457 Parts Guide (Code: 00ZAL1457//P1)
[Note]
Click on the first or last page to see other AL-1457D (serv.man6) service manuals if exist.