Sharp AL-1457D (serv.man10) User Manual / Operation Manual ▷ View online
7
2
Follow the installation procedure below to use the unit properly.
SETUP PROCEDURE
When using the unit for the first time, setup the unit following the procedure shown below.
*
1
The multi-bypass tray is only included with the AL-1457D and AL-1555.
*
2
If you are only using the unit for copying, skip this step.
If the unit does not function properly during setup or use, or if a function
cannot be used, see "TROUBLESHOOTING THE UNIT" (p.61).
cannot be used, see "TROUBLESHOOTING THE UNIT" (p.61).
1 Open the package, and make sure that all the accessories are
supplied with the unit. (p.8)
2 Remove the protective materials. (p.9)
3 Install the TD cartridge. (p.10)
4 Load the paper in the paper tray (p.15) or the multi-bypass
tray*
1
.
(p.17)
6 Connect the power cord. (p.12)
9 Now, you can copy (p.46), print (p.33), or scan (p.35) your
document.
8 Connect the interface cable*
2
(p.45) and turn on the unit. (p.12)
7 Install the software.*
2
(p.19)
5 Insert the attached power cord into the power cord socket at the
rear of the unit.
2
SETTING UP THE UNIT
8
CHECKING PACKED COMPONENTS AND
ACCESSORIES
ACCESSORIES
Open the carton and check if the following components and accessories are
included.
If anything is not included or is damaged, contact your authorised service
representative.
included.
If anything is not included or is damaged, contact your authorised service
representative.
PREPARING THE UNIT FOR INSTALLATION
1
Be sure to hold the handles on
both sides of the unit to unpack
the unit and carry it to the
installation location.
both sides of the unit to unpack
the unit and carry it to the
installation location.
Drum cartridge
(installed in unit)
Operation manual
AL-1217D
AL-1457D
AL-1555
AL-1457D
AL-1555
Software CD-ROM
TD cartridge
9
2
2
Remove all pieces of tape shown in the illustration below. Then
open the original cover/SPF/RSPF and remove protective
materials. After that, take out the bag containing the power
cord and TD cartridge.
open the original cover/SPF/RSPF and remove protective
materials. After that, take out the bag containing the power
cord and TD cartridge.
3
Release the scan head locking switch.
The scan head locking switch is under the original table.
If the switch is locked (
If the switch is locked (
)
, the unit will not operate. Unlock the switch (
)
as shown below.
(AL-1555 only)
(AL-1555)
AL-1217D
AL-1457D, AL-1555
AL-1217D
AL-1457D, AL-1555
Lock
Unlock
Grasp here and turn in
the direction of the arrow.
the direction of the arrow.
10
INSTALLING THE TD CARTRIDGE
1
Open the multi-bypass tray
(AL-1457D, AL-1555, p.17),
and then open the side
cover.
(AL-1457D, AL-1555, p.17),
and then open the side
cover.
2
Push gently on both sides of the
front cover to open the cover.
front cover to open the cover.
3
Remove the TD cartridge from the bag. Hold the cartridge on
both sides and shake it horizontally four or five times. Hold the
tab of the protective cover and pull the tab to your side to
remove the cover.
both sides and shake it horizontally four or five times. Hold the
tab of the protective cover and pull the tab to your side to
remove the cover.
4
Gently insert the TD cartridge
until it locks in place while
pushing the lock release button.
until it locks in place while
pushing the lock release button.
4 or 5 times
Click on the first or last page to see other AL-1457D (serv.man10) service manuals if exist.