Sharp AL-1457 (serv.man9) Service Manual ▷ View online
AL-1457 SIMULATION, TROUBLE CODES 10 - 5
24
01
JAM total counter clear
When the PRINT switch is pressed, the JAM total count value is reset to 0.
When the PRINT switch is pressed, the JAM total count value is reset to 0.
04
SPF counter clear
When the PRINT switch is pressed, the SPF count value is reset to 0.
When the PRINT switch is pressed, the SPF count value is reset to 0.
07
Drum counter clear
When the PRINT switch is pressed, the drum count value is reset to 0.
When the PRINT switch is pressed, the drum count value is reset to 0.
08
Copy counter clear
When the PRINT switch is pressed, the copy count value is reset to 0.
When the PRINT switch is pressed, the copy count value is reset to 0.
09
Printer counter clear
When the PRINT switch is pressed, the printer count value is reset to 0.
When the PRINT switch is pressed, the printer count value is reset to 0.
13
Scanner counter clear
When the PRINT switch is pressed, the scanner count value is reset to 0.
When the PRINT switch is pressed, the scanner count value is reset to 0.
14
SPF JAM total counter clear
When the PRINT switch is pressed, the SPF JAM total count value is reset to 0.
When the PRINT switch is pressed, the SPF JAM total count value is reset to 0.
15
Scanner mode counter clear
When the PRINT switch is pressed, the scanner mode counter is reset to 0.
When the PRINT switch is pressed, the scanner mode counter is reset to 0.
25
01
Main motor operation check (Cooling fan motor rotation check)
When the PRINT switch is pressed, the main motor (as well as the duplex motor in the duplex model) is operated for 30 sec. If the
developing unit is installed at that time, the developing bias, the main charger, and the grid are outputted together in order to avoid
toner consumption. Since, in this case, laser discharge is required when stopping the motor, the polygon motor is rotated at the same
time. If the developing unit is not installed, the above high voltage is not outputted and only the motor is rotated.
When the PRINT switch is pressed, the main motor (as well as the duplex motor in the duplex model) is operated for 30 sec. If the
developing unit is installed at that time, the developing bias, the main charger, and the grid are outputted together in order to avoid
toner consumption. Since, in this case, laser discharge is required when stopping the motor, the polygon motor is rotated at the same
time. If the developing unit is not installed, the above high voltage is not outputted and only the motor is rotated.
: Do not execute this simulation by forcibly turning ON the door ON/OFF switch.
10
Polygon motor ON
(Operation/Procedure)
When the START key is pressed, the polygon motor is operated for 30 sec.
(Operation/Procedure)
When the START key is pressed, the polygon motor is operated for 30 sec.
26
01
Manual feed setup
(Operation/Procedure)
1. When this simulation is executed, the currently set bypass code number is displayed.
2. Enter the code number corresponding to the bypass and press the START key, and the setting will be changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set bypass code number is displayed.
2. Enter the code number corresponding to the bypass and press the START key, and the setting will be changed.
02
(R) SPF setup
When this simulation is executed, the current setup of the SPF code number is displayed. Enter the code number corresponding to the
SPF and press the PRINT switch to enable the setup.
When this simulation is executed, the current setup of the SPF code number is displayed. Enter the code number corresponding to the
SPF and press the PRINT switch to enable the setup.
03
Second cassette setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the second cassette is displayed.
2. Enter the code number and press the start key. The setting is changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the second cassette is displayed.
2. Enter the code number and press the start key. The setting is changed.
04
Machine duplex setup
(Operation/Procedure)
1. When this simulation is executed, the currently set duplex code number is displayed.
2. Enter the code number corresponding to the duplex and press the ENTER key, and the setup will be changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set duplex code number is displayed.
2. Enter the code number corresponding to the duplex and press the ENTER key, and the setup will be changed.
Main
code
code
Sub
code
Content
Code number
Bypass
0
Single bypass
1
Multi bypass
Code number
SPF
0
SPF not installed
1
SPF installed
2
RSPF installed
Code number
Second cassette
0
Without second cassette
1
With second cassette
Code number
Duplex
0
Without Duplex
1
With Duplex
AL-1457 SIMULATION, TROUBLE CODES 10 - 6
26
06
Destination setup
When this simulation is executed, the current setup of the destination code number is displayed. Enter the code number corresponding
to the destination and press the PRINT switch to enable the setup.
When this simulation is executed, the current setup of the destination code number is displayed. Enter the code number corresponding
to the destination and press the PRINT switch to enable the setup.
07
Machine conditions check
When this simulation is executed, the current machine setup is displayed.
When this simulation is executed, the current machine setup is displayed.
20
Rear edge void setup
When this simulation is executed, the current setup of the rear edge void code number is displayed. Enter the code number
corresponding to the rear edge void and press the PRINT switch to enable the setup.
When this simulation is executed, the current setup of the rear edge void code number is displayed. Enter the code number
corresponding to the rear edge void and press the PRINT switch to enable the setup.
30
CE mark support control ON/OFF
When this simulation is executed, the current setup of the CE mark support code number is displayed. Enter the code number
corresponding to the CE mark support setup and press the PRINT switch to enable the setup.
When this simulation is executed, the current setup of the CE mark support code number is displayed. Enter the code number
corresponding to the CE mark support setup and press the PRINT switch to enable the setup.
38
Cancel of stop at drum life over
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT
switch to enable the setup.
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT
switch to enable the setup.
39
Memory capacity check
When this simulation is executed, the current memory capacity is displayed.
When this simulation is executed, the current memory capacity is displayed.
40
Polygon motor OFF time setup (Time required for turning OFF after completion of printing)
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT
switch to enable the setup.
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT
switch to enable the setup.
Main
code
code
Sub
code
Content
Code number
Destination
0
Inch series
1
EX JAPAN AB series
2
JAPAN AB series
3
China (EX JAPAN AB series + Chinese paper support)
CPM
Copy quantity display
10 cpm
10
12 cpm
12
13 cpm
13
14 cpm
14
15 cpm
15
Code number
Rear edge void setup
0
Rear edge void provided * Default
1
Rear edge void not provided
The default for CE-support 200V series is “1.”
Code number
CE mark support setup
0
CE mark support control OFF * Default (100V series)
1
CE mark support control ON
Code number
Setup
0
Stop at drum life over * Default (AL model)
1
Cancel of stop at drum life over
Code number
Setup
8
8 Mbyte
16
16 Mbyte
Code number
Setup
0
0 sec
1
30 sec * Default
2
60 sec
3
90 sec
AL-1457 SIMULATION, TROUBLE CODES 10 - 7
26
42
Transfer ON timing control setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed. (For any number different from the following
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed. (For any number different from the following
ones, the default time is automatically set.)
43
Side void setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the side void amount is displayed.
2. Enter the code number and press the start key. The setting is changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the side void amount is displayed.
2. Enter the code number and press the start key. The setting is changed.
44
SPF document rear edge read setup + Fax document rear edge scan setup.
When this simulation is executed, the currently set code number is displayed. Enter the desired code number and press the START
key, and the display will be changed. The document rear edge scanning area in SPF reduction (less than 100%) copy is changed.
The code number is changeable in the range of 0 – 8.
The default value is 4, and 2 mm of the document rear edge is cut.
When the value is changed by 1, the area is changed by 1 mm.
When this simulation is executed, the currently set code number is displayed. Enter the desired code number and press the START
key, and the display will be changed. The document rear edge scanning area in SPF reduction (less than 100%) copy is changed.
The code number is changeable in the range of 0 – 8.
The default value is 4, and 2 mm of the document rear edge is cut.
When the value is changed by 1, the area is changed by 1 mm.
62
Energy-save mode copy lamp setup
Used to set half-ON (50%)/OFF of the copy lamp in the pre-heat mode.
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT
switch to enable the setup.
Used to set half-ON (50%)/OFF of the copy lamp in the pre-heat mode.
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT
switch to enable the setup.
63
Fan control select setup
Used to set the cooling fan operation mode.
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT
switch to enable the setup.
Used to set the cooling fan operation mode.
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT
switch to enable the setup.
Main
code
code
Sub
code
Content
Code number
Setting
0
Default (330 msec)
1
– 40 msec
2
– 30 msec
3
– 20 msec
4
– 10 msec
5
Default (330 msec)
6
+10 msec
7
+20 msec
8
+30 msec
9
+40 msec
Code number
Setting
0
0 mm
1
0.5 mm
2
1.0 mm
3
1.5 mm
4
2.0 mm * Default
5
2.5 mm
6
3.0 mm
7
3.5 mm
8
4.0 mm
9
4.5 mm
10
5.0 mm
Code number
Setup
0
Copy lamp half-ON (50%) * Default
1
Copy lamp OFF
Code number
Setup
1
1-speed fan control
2
2-speed fan control * Default when starting mass production
AL-1457 SIMULATION, TROUBLE CODES 10 - 8
30
01
Paper sensor status display
Indicates the paper sensor status using the lamps on the operation panel.
Indicates the paper sensor status using the lamps on the operation panel.
43
01
Fusing temperature setup (Normal copy)
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
04
Fusing temperature setup 2
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
05
Fusing temperature setup in duplex copy
In duplex copy, this setup value is added to the fusing temperature of single copy. When this simulation is executed, the current setup
of the code number is displayed. Enter the code number and press the PRINT switch to enable the setup.
In duplex copy, this setup value is added to the fusing temperature of single copy. When this simulation is executed, the current setup
of the code number is displayed. Enter the code number and press the PRINT switch to enable the setup.
09
Setup of fusing control of postcard size paper
Main
code
code
Sub
code
Content
Sensor name
Display lamp
Before-resist paper sensor (PPD1)
Developer cartridge replacement lamp
Fusing section paper sensor (PPD2)
JAM lamp
Paper exit sensor (POD)
Photoconductor cartridge replacement lamp
2nd CS paper sensor (PPD3)
2nd cassette lamp
New drum cartridge sensor (PUIS)
Zoom lamp
Single manual feed paper sensor (MFD)
AE lamp
Code number
Set temperature (°C)
0
175
1
180
2
185
3
190
4
195 (* Default)
5
200
Code number
Set temperature (°C)
0
155
1
160
2
165
3
170 (* Default)
4
175
5
180
Code number
Temperature shift (°C)
0
±0°C * Default
1
– 8°C
2
– 6°C
3
– 4°C
4
– 2°C
5
±0°C
6
+2°C
7
+4°C
8
+6°C
9
+8°C
The default for Japan model is “1.”
Code number
Setup
0
Cancel * Default
1
Setup
Click on the first or last page to see other AL-1457 (serv.man9) service manuals if exist.