DOWNLOAD Sharp AL-1457 (serv.man9) Service Manual ↓ Size: 89.92 KB | Pages: 14 in PDF or view online for FREE

Model
AL-1457 (serv.man9)
Pages
14
Size
89.92 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Sect.10 Simulations Trouble Codes
File
al-1457-sm9.pdf
Date

Sharp AL-1457 (serv.man9) Service Manual ▷ View online

AL-1457  SIMULATION, TROUBLE CODES  10 - 4
07
01
Warm-up display and aging with jam
(Operation/Procedure)
1. When the simulation is executed, warming up is started.
2. Warm-up time is counted and displayed every second on the copy quantity display.
3. After completion of warm-up, the time count is stopped and the ready lamp is lighted.
4. Press the clear key to clear the warm-up time display, set the copy quantity, and press the START key, and the machine will copy 
the set quantity repeatedly.
This simulation is canceled by turning off the power or executing any simulation which performs hardware reset.
06
Intermittent aging
(Operation/Procedure)
1. When the simulation is executed, warming up is started.
2. After completion of warm-up, the ready lamp is lighted.
3. Set the copy quantity and press the START key, and the machine will copy the set quantity repeatedly.
4. After 3 sec of the interval time from completion of copying the set quantity, the machine will resume copying.
5. The above operation 4 is repeated.
This simulation is canceled by turning off the power or executing any simulation which performs hardware reset.
08
01
Developing bias  
(Operation/Procedure)  
When the START key is pressed, the developing bias is outputted for 30 sec.
02
Main charger (Grid high)  
(Operation/Procedure) 
When the START key is pressed, the main charger output is supplied for 30 sec in the grid voltage HIGH mode.
03
Grid voltage (Low)  
(Operation/Procedure)  
When the START key is pressed, the main charger output is supplied for 30 sec in the grid voltage LOW mode.
06
Transfer charger  
(Operation/Procedure)  
When the START key is pressed, the transfer charger output is supplied for 30 sec.
10
None  Toner motor aging  
(Operation/Procedure) 
When the START key is pressed, the toner motor output is supplied for 30 sec.
14
None  Cancel of troubles other than U2  
(Operation/Procedure) 
After canceling the trouble, the simulation is also automatically canceled.
16
None  Cancel of U2 trouble
(Operation/Procedure)
1. When the START key is pressed, the EEPROM total counter check sum is rewritten and the trouble is canceled.
2. After canceling the trouble, the simulation is also automatically canceled.
22
04
JAM total counter display
The display method is the same as the total count value display.
05
Total counter display  
The total count value is displayed in 3 digits X 2 times repeatedly. 
<Display example: 12345>  
08
SPF counter display
The display method is the same as the total count value display.
12
Drum counter display
The display method is the same as the total count value display.
14
P-ROM version display
The main code and the sub code of the P-ROM version is displayed on the value display section in 2 digits alternately.
The display method is the same as the total count value display.
17
Copy counter display
The display method is the same as the total count value display.
18
Printer counter display
The display method is the same as the total count value display.
19
Scanner mode counter display
The display method is the same as the total count value display.
21
Scanner counter display
The display method is the same as the total count value display.
22
SPF JAM counter display
The display method is the same as the total count value display.
Main 
code
Sub 
code
Content
012 
→ Blank → 345 → Blank → 012
0.7s
0.3s 0.7s
1.0s
0.7s
AL-1457  SIMULATION, TROUBLE CODES  10 - 5
24
01
JAM total counter clear
When the PRINT switch is pressed, the JAM total count value is reset to 0.
04
SPF counter clear
When the PRINT switch is pressed, the SPF count value is reset to 0.
07
Drum counter clear
When the PRINT switch is pressed, the drum count value is reset to 0.
08
Copy counter clear
When the PRINT switch is pressed, the copy count value is reset to 0.
09
Printer counter clear
When the PRINT switch is pressed, the printer count value is reset to 0.
13
Scanner counter clear
When the PRINT switch is pressed, the scanner count value is reset to 0.
14
SPF JAM total counter clear
When the PRINT switch is pressed, the SPF JAM total count value is reset to 0.
15
Scanner mode counter clear
When the PRINT switch is pressed, the scanner mode counter is reset to 0.
25
01
Main motor operation check (Cooling fan motor rotation check)
When the PRINT switch is pressed, the main motor (as well as the duplex motor in the duplex model) is operated for 30 sec. If the 
developing unit is installed at that time, the developing bias, the main charger, and the grid are outputted together in order to avoid 
toner consumption. Since, in this case, laser discharge is required when stopping the motor, the polygon motor is rotated at the same 
time. If the developing unit is not installed, the above high voltage is not outputted and only the motor is rotated.
: Do not execute this simulation by forcibly turning ON the door ON/OFF switch.
10
Polygon motor ON  
(Operation/Procedure)  
When the START key is pressed, the polygon motor is operated for 30 sec.
26
01
Manual feed setup
(Operation/Procedure)
1. When this simulation is executed, the currently set bypass code number is displayed.
2. Enter the code number corresponding to the bypass and press the START key, and the setting will be changed.
02
(R) SPF setup
When this simulation is executed, the current setup of the SPF code number is displayed. Enter the code number corresponding to the 
SPF and press the PRINT switch to enable the setup. 
03
Second cassette setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the second cassette is displayed.
2. Enter the code number and press the start key. The setting is changed.
04
Machine duplex setup
(Operation/Procedure)
1. When this simulation is executed, the currently set duplex code number is displayed.
2. Enter the code number corresponding to the duplex and press the ENTER key, and the setup will be changed.
Main 
code
Sub 
code
Content
Code number
Bypass
0
Single bypass
1
Multi bypass
Code number
SPF
0
SPF not installed
1
SPF installed
2
RSPF installed
Code number
Second cassette
0
Without second cassette
1
With second cassette
Code number
Duplex
0
Without Duplex
1
With Duplex
AL-1457  SIMULATION, TROUBLE CODES  10 - 6
26
06
Destination setup
When this simulation is executed, the current setup of the destination code number is displayed. Enter the code number corresponding 
to the destination and press the PRINT switch to enable the setup.
07
Machine conditions check
When this simulation is executed, the current machine setup is displayed.
20
Rear edge void setup
When this simulation is executed, the current setup of the rear edge void code number is displayed. Enter the code number 
corresponding to the rear edge void and press the PRINT switch to enable the setup. 
30
CE mark support control ON/OFF
When this simulation is executed, the current setup of the CE mark support code number is displayed. Enter the code number 
corresponding to the CE mark support setup and press the PRINT switch to enable the setup. 
38
Cancel of stop at drum life over
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT 
switch to enable the setup. 
39
Memory capacity check
When this simulation is executed, the current memory capacity is displayed. 
40
Polygon motor OFF time setup (Time required for turning OFF after completion of printing)
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT 
switch to enable the setup. 
Main 
code
Sub 
code
Content
Code number
Destination
0
Inch series
1
EX JAPAN  AB series
2
JAPAN AB series
3
China (EX JAPAN AB series + Chinese paper support)
CPM
Copy quantity display
10 cpm 
10
12 cpm 
12
13 cpm
13
14 cpm
14
15 cpm 
15
Code number
Rear edge void setup
0
Rear edge void provided * Default
1
Rear edge void not provided
The default for CE-support 200V series is “1.”
Code number
CE mark support setup
0
CE mark support control OFF * Default (100V series)
1
CE mark support control ON
Code number
Setup
0
Stop at drum life over * Default (AL model)
1
Cancel of stop at drum life over
Code number
Setup
8
8  Mbyte
16
16 Mbyte
Code number
Setup
0
0 sec
1
30 sec * Default
2
60 sec
3
90 sec
AL-1457  SIMULATION, TROUBLE CODES  10 - 7
26
42
Transfer ON timing control setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed. (For any number different from the following 
ones, the default time is automatically set.)
43
Side void setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the side void amount is displayed.
2. Enter the code number and press the start key. The setting is changed.
44
SPF document rear edge read setup + Fax document rear edge scan setup.
When this simulation is executed, the currently set code number is displayed. Enter the desired code number and press the START 
key, and the display will be changed. The document rear edge scanning area in SPF reduction (less than 100%) copy is changed.
The code number is changeable in the range of 0 – 8.
The default value is 4, and 2 mm of the document rear edge is cut.
When the value is changed by 1, the area is changed by 1 mm.
62
Energy-save mode copy lamp setup
Used to set half-ON (50%)/OFF of the copy lamp in the pre-heat mode.
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT 
switch to enable the setup.
63
Fan control select setup
Used to set the cooling fan operation mode.
When this simulation is executed, the current setup of the code number is displayed. Enter the code number and press the PRINT 
switch to enable the setup.
Main 
code
Sub 
code
Content
Code number
Setting
0
Default (330 msec)
1
– 40 msec
2
– 30 msec
3
– 20 msec
4
– 10 msec
5
Default (330 msec)
6
+10 msec
7
+20 msec
8
+30 msec
9
+40 msec
Code number
Setting
0
0  mm
1
0.5 mm
2
1.0 mm
3
1.5 mm
4
2.0 mm * Default
5
2.5 mm
6
3.0 mm
7
3.5 mm
8
4.0 mm
9
4.5 mm
10
5.0 mm
Code number
Setup
0
Copy lamp half-ON (50%) * Default
1
Copy lamp OFF
Code number
Setup
1
1-speed fan control
2
2-speed fan control * Default when starting mass production
Page of 14
Display

Sharp AL-1457 (serv.man9) Service Manual ▷ Download

  • DOWNLOAD Sharp AL-1457 (serv.man9) Service Manual ↓ Size: 89.92 KB | Pages: 14 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp AL-1457 (serv.man9) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp AL-1457 (serv.man9) Copying Equipment. Information contained in Sharp AL-1457 (serv.man9) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.