Sharp AL-1457 (serv.man33) User Manual / Operation Manual ▷ View online
15
3
LOADING THE PAPER TRAY
1
Raise the handle of the paper tray
and pull the paper tray out until it
stops.
and pull the paper tray out until it
stops.
2
Remove the pressure plate lock. Rotate the pressure plate lock
in the direction of the arrow to remove it while pressing down
the pressure plate of the paper tray.
in the direction of the arrow to remove it while pressing down
the pressure plate of the paper tray.
3
Store the pressure plate lock which has been removed in step 2.
To store the pressure plate lock, rotate the lock to fix it on the
relevant location.
To store the pressure plate lock, rotate the lock to fix it on the
relevant location.
4
Adjust the paper guides on the paper tray to the copy paper
width and length. Squeeze the lever of paper guide
width and length. Squeeze the lever of paper guide
and slide
the guide to match with the width of the paper. Move paper
guide
guide
to the appropriate slot as marked on the tray.
Pressure plate lock
A
B
Paper
guide B
guide B
Paper
guide A
guide A
16
5
Fan the paper and insert it into the tray. Make sure the edges go
under the corner hooks.
under the corner hooks.
6
Gently push the paper tray back into the unit.
Do not load paper above the maximum height line (
). Exceeding
the line will cause a paper misfeed.
•
After loading paper, to cancel the blinking
without restarting
copying, press the clear (
) key. The
in the display will go out
and the start (
) indicator will light up.
•
Be sure that paper is free of rips, dust, wrinkles, and curled or bent
edges.
edges.
•
Make sure all the paper in the stack is the same size and type.
•
When loading paper, ensure there is no space between the paper and
the guide, and check if the guide is not set too narrow causing the
paper to bend. Loading paper in these ways will result in document
skew or a paper jam.
the guide, and check if the guide is not set too narrow causing the
paper to bend. Loading paper in these ways will result in document
skew or a paper jam.
•
When not using the unit for an extended period, remove all paper from
the paper tray and store it in a dry place. If paper is left in the unit for
an extended period, the paper will absorb moisture from the air,
resulting in paper jams.
the paper tray and store it in a dry place. If paper is left in the unit for
an extended period, the paper will absorb moisture from the air,
resulting in paper jams.
•
When adding new paper to the paper tray, remove the old paper
already contained in the tray. Placing new paper on top of the paper
already contained in the tray may result in feeding two sheets at one
time.
already contained in the tray. Placing new paper on top of the paper
already contained in the tray may result in feeding two sheets at one
time.
17
3
BYPASS FEED (including special paper)
The multi-bypass tray (AL-1457) or the single bypass (AL-1217) can be used to feed
standard paper, transparency film, labels, envelopes, and other special purpose
paper. Paper measuring from A6 to A4 and in the weight range of 52
standard paper, transparency film, labels, envelopes, and other special purpose
paper. Paper measuring from A6 to A4 and in the weight range of 52
g
/m
2
to 128
g
/
m
2
can be used in this tray. (For paper weighing from 104
g
/m
2
to 128
g
/m
2
, A4 is the
maximum size.)
The multi-bypass tray (AL-1457)
1
Open the multi-bypass tray and extend the tray.
2
Set the paper guides to the paper width. Insert the paper (print
face down) all the way into the multi-bypass tray.
face down) all the way into the multi-bypass tray.
•
The multi-bypass tray (AL-1457) can hold maximum of 50 sheets of
paper. (Capacity will vary depending on the type of paper loaded.)
The single bypass (AL-1217) can hold one sheet of paper.
paper. (Capacity will vary depending on the type of paper loaded.)
The single bypass (AL-1217) can hold one sheet of paper.
•
The original image must be smaller than the paper or media for
copying. If the original image is bigger than the paper or media, this
may cause smudges on the edges of the copies.
copying. If the original image is bigger than the paper or media, this
may cause smudges on the edges of the copies.
To close the multi-
bypass tray,
perform step 1
and then step 2 in
the illustration and
push the round
projections at the
right of the tray
until they click.
bypass tray,
perform step 1
and then step 2 in
the illustration and
push the round
projections at the
right of the tray
until they click.
Print face
18
3
Press the tray select (
) key to select the multi-bypass tray.
The single bypass (AL-1217)
1
Select copy settings before you begin the copy job.
For information on the copy settings, see "MAKING COPIES" (p.46)". For
information on the print settings, see the online manual or the Help file for
the printer driver, and then begin printing from the single bypass.
information on the print settings, see the online manual or the Help file for
the printer driver, and then begin printing from the single bypass.
2
Set the paper guides to the paper width. Insert a single sheet of
copy or print paper (print face down) into the feed slot of the
single bypass.
copy or print paper (print face down) into the feed slot of the
single bypass.
Using copy mode
When you insert the paper, the machine will automatically draw in the paper
and begin copying.
Using printer mode
After
When you insert the paper, the machine will automatically draw in the paper
and begin copying.
Using printer mode
After
appears in the
display, wait until the Paper
feed location indicator for the
single bypass illuminates and
insert the paper. The machine
will automatically draw in the
paper and begin printing.
feed location indicator for the
single bypass illuminates and
insert the paper. The machine
will automatically draw in the
paper and begin printing.
•
Paper must be fed narrow side into the feed slot.
•
Special papers such as transparency film ,labels and
envelopes must be fed one sheet at a time through the multi-
bypass tray.
envelopes must be fed one sheet at a time through the multi-
bypass tray.
•
When copying onto transparency film, remove each copy
promptly. Do not let copies stack up.
promptly. Do not let copies stack up.
•
If you insert a sheet of paper into the single bypass when multiple
copies have been set with the copy quantity setting (p.49), the copy
quantity setting will change to "0" and only one copy will be made.
copies have been set with the copy quantity setting (p.49), the copy
quantity setting will change to "0" and only one copy will be made.
•
When copying onto transparency film, remove each copy promptly.
Do not let copies stack up.
Do not let copies stack up.
Note for loading envelopes
• Envelopes must be fed narrow side into the feed slot one at a time.
• Do not use non-standard envelopes, and envelopes that have metal clasps, plastic
• Do not use non-standard envelopes, and envelopes that have metal clasps, plastic
snappers, string closures, windows, linings, self-adhesive, patches or synthetic
materials. Do not use envelopes that are filled with air or envelopes that have labels
or stamps attached.
materials. Do not use envelopes that are filled with air or envelopes that have labels
or stamps attached.
• Envelopes of which the surface is not flat because of embossing may cause the
copies/prints to become smudged.
• Under high humidity and temperature conditions the glue flaps on some envelopes
may become sticky and be sealed closed when copied/printed.
• Use only envelopes which are flat and crisply folded. Curled or poorly formed
envelopes may be poorly copied/printed or may cause misfeeds.
• Be sure to select either Com10, DL, C5 or Monarch on the paper size setting of the
printer driver. (For detailed information on printer driver, refer to the online manual.)
• It is recommended that you perform a test copy/print before performing the actual
copied/printed job.
Print face
Click on the first or last page to see other AL-1457 (serv.man33) service manuals if exist.