Sharp AL-1217 (serv.man23) User Manual / Operation Manual ▷ View online
9
2
2
Remove all pieces of tape shown in the illustration below. Then
open the original cover/SPF and remove protective materials.
After that, take out the bag containing the power cord and TD
cartridge.
open the original cover/SPF and remove protective materials.
After that, take out the bag containing the power cord and TD
cartridge.
3
Release the scan head locking switch.
The scan head locking switch is under the original table.
If the switch is locked (
If the switch is locked (
)
, the unit will not operate. Unlock the switch (
)
as shown below.
AL-1217
AL-1457
Lock
Unlock
Grasp here and turn in
the direction of the arrow.
the direction of the arrow.
10
INSTALLING THE TD CARTRIDGE
1
Open the multi-bypass tray
(AL-1457, p.17), and then
open the side cover.
(AL-1457, p.17), and then
open the side cover.
2
Remove the CAUTION tape from the front cover and remove the
two protective pins from the fusing unit by pulling the strings
upward one at a time.
two protective pins from the fusing unit by pulling the strings
upward one at a time.
3
Push gently on both sides of the
front cover to open the cover.
front cover to open the cover.
4
Remove the TD cartridge from the bag. Remove the protective
paper. Hold the cartridge on both sides and shake it
horizontally four or five times. Hold the tab of the protective
cover and pull the tab to your side to remove the cover.
paper. Hold the cartridge on both sides and shake it
horizontally four or five times. Hold the tab of the protective
cover and pull the tab to your side to remove the cover.
CAUTION tape
Protective pins
4 or 5 times
11
2
5
Gently insert the TD cartridge
until it locks in place while
pushing the lock release button.
until it locks in place while
pushing the lock release button.
6
Close the front cover and then
the side cover by pressing the
round projections near the
side cover open button.
the side cover by pressing the
round projections near the
side cover open button.
When closing the covers, be
sure to close the front cover
securely and then close the
side cover. If the covers are
closed in the wrong order, the
covers may be damaged.
sure to close the front cover
securely and then close the
side cover. If the covers are
closed in the wrong order, the
covers may be damaged.
12
CONNECTING THE POWER CORD
1
Ensure that the power switch of
the unit is in the OFF position.
Insert the attached power cord
into the power cord socket at the
rear of the unit.
the unit is in the OFF position.
Insert the attached power cord
into the power cord socket at the
rear of the unit.
2
Plug the other end of the power cord into the nearest outlet.
Power on
Ensure that the power switch of the unit is in the OFF position. Plug the other end of
the power cord into the nearest outlet. Turn the power switch on the left side of the
unit to the "ON" position. The start (
the power cord into the nearest outlet. Turn the power switch on the left side of the
unit to the "ON" position. The start (
) indicator will light up and other indicators
which show the initial settings of the operation panel will also light up to indicate the
ready condition. For the initial settings, see the "Initial settings of operation panel"
described on the next page.
ready condition. For the initial settings, see the "Initial settings of operation panel"
described on the next page.
If you use the unit in a country other than the country where the unit was
purchased, you will need to make sure that your local power supply is
compatible with your model. If you plug the unit into an incompatible
power supply, irreparable damage to the unit will result.
purchased, you will need to make sure that your local power supply is
compatible with your model. If you plug the unit into an incompatible
power supply, irreparable damage to the unit will result.
Only insert the power cord into a properly grounded wall socket.
Do not use extension cords or power strips.
Do not use extension cords or power strips.
•
The unit will enter a power save mode once the set time has elapsed
without any unit operation. The settings of the power save modes can
be modified. See "USER PROGRAMS" (p.53).
without any unit operation. The settings of the power save modes can
be modified. See "USER PROGRAMS" (p.53).
•
The unit will return to the initial settings a preset amount of time after
the end of copy or scanner job. The preset amount of time (auto clear
time) can be changed. See "USER PROGRAMS" (p.53).
the end of copy or scanner job. The preset amount of time (auto clear
time) can be changed. See "USER PROGRAMS" (p.53).
Display