DOWNLOAD Sharp AL-1045 (serv.man6) Service Manual ↓ Size: 609 KB | Pages: 9 in PDF or view online for FREE

AL-1555 UNPACKING AND INSTALLATION 5 - 8

4. When the "Select Program Folder" window appears, click the

"Next" button.

The setup program will start to copy the files.

If the dialog box asking "If you have TIFF files saved using
Photo-Shop or Imaging for Windows you should hit Skip"
appears. Answer the question to continue the Sharpdesk instal-
lation.

5. Click the "Finish" button when the message to inform you of the

completion of the installation appears.

9) Click the "Close" button when the message to inform you of the

completion of the installation appears.

• After the installation, a message to restart your computer may be

displayed. In this case, click the "Yes" button to restart your com-
puter.

10) Connect the parallel interface cable.

You have completed the installation of all the software.

• For parallel interface connection ensure that your computer and

MFP are turned off before connecting the cable (see page 5-8).

This unit includes both USB and parallel interface connectors.
Interface cables for connecting the unit to your computer are not
included with this unit.

Caution:

• If you intend to use the unit as a scanner, it must be connected to

your computer with a USB interface cable. The scanner function can-
not be used if the unit is connected with a parallel cable.

• USB is available with a PC/AT compatible computer that was origi-

nally equipped with USB and had Windows 98, Windows Me, Win-
dows 2000 Professional, Windows XP Professional or Windows XP
Home Edition preinstalled.

• Do not connect the interface cable before installing the MFP driver.

The interface cable should be connected during installa-tion of the
MFP driver.

1) Obtain a shielded USB interface cable.

2) Insert the cable into the USB interface connector located on the

rear of the unit.

3) Insert the other end of the cable into the interface connector of your

computer, or the USB hub connected to your computer.

1) Obtain an IEEE1284 shielded parallel interface cable.

2) Ensure that your computer and unit are turned off.

3) Insert the cable into the parallel interface connector located on the

rear of the unit, and fasten with clasps.

4) Insert the other end of the cable into the interface connector of your

computer.

This printer uses a bi-directional parallel interface. Use the supplied
interface cable.

36-pin ACON RBE42-36K1153 female connector or equivalent con-
nector

Shielded type bi-directional parallel interface For best results, use a
printer interface cable which is IEEE1284 compliant.

The pin numbers and signal names are listed in the following table.

Pin No.

Signal name

Pin No.

Signal name

1

STB

19

GND (STB RET)

2

DATA1

20

GND (DATA1 RET)

3

DATA2

21

GND (DATA2 RET)

4

DATA3

22

GND (DATA3 RET)

5

DATA4

23

GND (DATA4 RET)

6

DATA5

24

GND (DATA5 RET)

7

DATA6

25

GND (DATA6 RET)

8

DATA7

26

GND (DATA7 RET)

9

DATA8

27

GND (DATA8 RET)

10

ACKNLG

28

GND 
(ACKNLG RET)

11

BUSY

29

GND (BUSY RET)

12

PE (Paper End)

30

GND (PE RET)

13

SLTC

31

INPRM

14

AUTO LF

32

FAULT

15

(NC)

33

(NC)

16

GND (0 V)

34

(NC)

17

FG

35

+5 V

18

+5 V

36

SLTC IN

1

18

36

19

AL-1555 UNPACKING AND INSTALLATION 5 - 9

4-pin ACON UBR23-4K2200

Type-B connector

Shielded twisted pair cable

(2 m (6 feet) Max.: high-speed transmission equivalent)

The pin numbers and signal names are listed in the following table.

When moving the unit, follow the procedure below.

Note: When moving this unit, be sure to remove the TD cartridge in

advance.

1) Turn the power switch off and remove the power cord from the out-

let.

2) Open the side cover and front cover, in that order. Remove the TD

cartridge and close the front cover and side cover, in that order.

To open and close the side cover and front cover, and to remove
the TD cartridge, see "TD CARTRIDGE REPLACEMENT".

3) Raise the handle of the paper tray and pull the paper tray out until it

stops.

4) Push the center of the pressure plate down until it locks in place

5) Push the paper tray back into the unit.

6) Lock the scan head locking switch.

Note: When shipping the unit, the scan head locking switch must be

locked to prevent shipping damage.

7) Close the multi-bypass tray and the paper output tray extension,

and attach the packing materials and tape which were removed
during installation of the unit. See "PREPARING THE UNIT FOR
INSTALLATION".

8) Pack the unit into the carton. See "CHECKING PACKED COMPO-

NENTS AND ACCESSORIES".

Pin No.

Signal name

1

+5V

2

-DATA

3

+DATA

4

GND

1

2

3

4

AL-1555 UNPACKING AND INSTALLATION 5 - 9

4-pin ACON UBR23-4K2200

Type-B connector

Shielded twisted pair cable

(2 m (6 feet) Max.: high-speed transmission equivalent)

The pin numbers and signal names are listed in the following table.

When moving the unit, follow the procedure below.

Note: When moving this unit, be sure to remove the TD cartridge in

advance.

1) Turn the power switch off and remove the power cord from the out-

let.

2) Open the side cover and front cover, in that order. Remove the TD

cartridge and close the front cover and side cover, in that order.

To open and close the side cover and front cover, and to remove
the TD cartridge, see "TD CARTRIDGE REPLACEMENT".

3) Raise the handle of the paper tray and pull the paper tray out until it

stops.

4) Push the center of the pressure plate down until it locks in place

5) Push the paper tray back into the unit.

6) Lock the scan head locking switch.

Note: When shipping the unit, the scan head locking switch must be

locked to prevent shipping damage.

7) Close the multi-bypass tray and the paper output tray extension,

and attach the packing materials and tape which were removed
during installation of the unit. See "PREPARING THE UNIT FOR
INSTALLATION".

8) Pack the unit into the carton. See "CHECKING PACKED COMPO-

NENTS AND ACCESSORIES".

Pin No.

Signal name

1

+5V

2

-DATA

3

+DATA

4

GND

1

2

3

4

AL-1555 UNPACKING AND INSTALLATION 5 - 9

4-pin ACON UBR23-4K2200

Type-B connector

Shielded twisted pair cable

(2 m (6 feet) Max.: high-speed transmission equivalent)

The pin numbers and signal names are listed in the following table.

When moving the unit, follow the procedure below.

Note: When moving this unit, be sure to remove the TD cartridge in

advance.

1) Turn the power switch off and remove the power cord from the out-

let.

2) Open the side cover and front cover, in that order. Remove the TD

cartridge and close the front cover and side cover, in that order.

To open and close the side cover and front cover, and to remove
the TD cartridge, see "TD CARTRIDGE REPLACEMENT".

3) Raise the handle of the paper tray and pull the paper tray out until it

stops.

4) Push the center of the pressure plate down until it locks in place

5) Push the paper tray back into the unit.

6) Lock the scan head locking switch.

Note: When shipping the unit, the scan head locking switch must be

locked to prevent shipping damage.

7) Close the multi-bypass tray and the paper output tray extension,

and attach the packing materials and tape which were removed
during installation of the unit. See "PREPARING THE UNIT FOR
INSTALLATION".

8) Pack the unit into the carton. See "CHECKING PACKED COMPO-

NENTS AND ACCESSORIES".

Pin No.

Signal name

1

+5V

2

-DATA

3

+DATA

4

GND

1

2

3

4