DOWNLOAD Sharp PN-V602 Service Manual ↓ Size: 504.07 KB | Pages: 13 in PDF or view online for FREE

Model
PN-V602
Pages
13
Size
504.07 KB
Type
PDF
Document
Handy Guide
Brand
Device
Monitor / Horizontal Installation Notes
File
pn-v602.pdf
Date

Sharp PN-V602 Handy Guide ▷ View online

PN-V601/V601A/PN-V602 Installation Manual for Multi Displays  <Rev3.0> 2013/10 
CONFIDENTIAL 
The setting for the horizontal installation in the OSD menu is required, when displays are installed horizontally. 
Face-up horizontal installation setting 
1) Press [SIZE] key for approx. 5 seconds. 
 
(and the character “F” appears in the upper left of the screen) 
2)  [    ][    ][    ][    ] 
1) Hold for approx 5 sec. both [MENU] and [INPUT] at the same time. 
    
(and the character “F” appears in the upper left of the screen)    
2)   [    ][    ][    ][    ] 
1. How to call menu  
CUSTOM SETTING 
MONITOR  LAYOUT 
FACE  UP 
- Change [VERTICAL] to [FACE UP]. 
- After checking the display, turn off the main 
power 
 
Note) 
 - Change the setting to [VERTICAL] in order to   
   change from horizontal installation to vertical one. 
- Do not use other setting. 
 
2. Setting of the face-up installation 
- If using the remote control unit 
- If using the monitor buttons on the rear panel,  
OK ---- [MENU] 
Setting of face-up horizontal installation 
Face-UP installation 
PN-V601/V601A/PN-V602 Installation Manual for Multi Displays  <Rev3.0> 2013/10 
CONFIDENTIAL 
Securing Space and Temperature Conditions 
Wall 
Display screen surface 
Protection panel etc. 
Secure space more than 10 cm 
Upper part of the unit 
Ventilation duct installed 
Fix the unit using VESA compliant holes.(toward the direction of yellow arrow) 
Securing Space and Temperature Conditions 
Secure space  
more than 20 cm 
Upper part of the unit 
Lower part of the unit 
Secure space  
over 20 cm 
Lower part of the unit 
Floor 
-Please secure space more than 20 cm from wall and floor in order to flow air smoothly. 
- It may be necessary to take measures in order for inner fan to exhaust air immediately (i.e. guide the air flow by duct). 
- It is necessary to keep the surrounding temperature under 30C degree. In other words, the air conditioner system must     
  work efficiently. The temperature at the heat outlet of fan
 
(upper side of the display: at the     part of illustration below)  
  must be kept under 35C degree.  
- If displays are overlaid with protection panel, the temperature of the space between display surface and protection panel  
   must be kept under 40C degree with cooling system.
 
(More than wind velocity 1m/s ) 
-- As the protection panel may transform and curves inward by heat depending on its material, it should be set and adjusted 
 considering necessary space between display and protection panel based on the flexure of protection panel,  
  load from upper part, installation method, or the material of protection panel etc. 
 (Please be careful that protection panel must not touch the display surface even if it is curved.)  
- Do not press the display surface and drop anything on the display surface. 
- Please be careful not to nip cables between display and mounting bracket. 
Face-UP installation 
PN-V601/V601A/PN-V602 Installation Manual for Multi Displays  <Rev3.0> 2013/10 
CONFIDENTIAL 
About Air Flow 
About Air Flow 
・ Air flows from lower part to upper part of the monitor (from right to left in the illustration below). 
・ Please do not disturb inhalation of cool air in order to satisfy the condition which mentioned in "Space securing  
  and temperature. (More than intake vent wind velocity 1m/s ) 
The cool air is inhaled (if the protection panel is equipped) 
Protection panel etc. 
Display screen surface 
The cool air  
is inhaled. 
Upper part  
of the unit 
(Fan) 
Upper part  
of the unit 
(Fan) 
Lower part  
of the unit 
Lower part  
of the unit 
Wall 
Ventilation duct installed 
Floor 
Face-UP installation 
PN-V601/V601A/PN-V602 Installation Manual for Multi Displays  <Rev3.0> 2013/10 
CONFIDENTIAL 
The setting for the horizontal installation in the OSD menu is required, when displays are installed horizontally. 
Face-down horizontal installation setting 
1) Press [SIZE] key for approx. 5 seconds. 
 
(and the character “F” appears in the upper left of the screen) 
2)  [    ][    ][    ][    ] 
1) Hold for approx 5 sec. both [MENU] and [INPUT] at the same time. 
    
(and the character “F” appears in the upper left of the screen)    
2)   [    ][    ][    ][    ] 
1. How to call menu  
CUSTOM SETTING 
MONITOR  LAYOUT 
FACE  DOWN 
- Change [VERTICAL] to [FACE DOWN]. 
- After checking the display, turn off the main 
power 
 
Note) 
 - Change the setting to [VERTICAL] in order to   
   change from horizontal installation to vertical one. 
- Do not use other setting. 
 
2. Setting of the face-down installation 
- If using the remote control unit 
- If using the monitor buttons on the rear panel,  
OK ---- [MENU] 
Setting of face-down horizontal installation 
Face-down installation 
Page of 13
Display

Click on the first or last page to see other PN-V602 service manuals if exist.