Sharp PN-V602 (serv.man6) Service Manual ▷ View online
CHAPTER 1. OUTLINE OF THE PRODUCT
PN-V602 OUTLINE OF THE PRODUCT
1 – 5
1 - 5. COMPATIBLE SIGNAL TIMING (AV)
*
1
Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed.
*
2
Available when the PN-ZB02 (optional) is attached.
1 - 6. POWER MANAGEMENT
This monitor conforms to VESA DPMS and DVI DMPM. Both your video
card and computer must support the same standard in order for the
monitor’s power management function to work.
DPMS: DISPLAY POWER MANAGEMENT SIGNALING
DMPM: DIGITAL MONITOR POWER MANAGEMENT
*
1
When PN-ZR01 (optional), or PN-ZB02 (optional) is not
connected.
*
2
When “AUTO INPUT CHANGE” is set to “OFF”.
1 - 7. POWER LIMITED
Set to ensure maximum power consumption.
3Refer to page 1 - 1 "1 - 1. OUTLINE".
1 - 8. DDC (PLUG AND PLAY)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and com-
puters. Information about resolution and other parameters is exchanged
between the two. This function can be used if the computer supports
between the two. This function can be used if the computer supports
DDC and it has been configured to detect plug-and-play monitors.
There are several types of DDC, depending on the communication
method used. This monitor supports DDC2B.
method used. This monitor supports DDC2B.
1 - 9.
SUPPLIED ACCESSORIES (PN-V602)
Screen resolution
Frequency
DVI-D
*2
HDMI
Component
*2
1920 x 1080p
*1
24Hz
---
Yes
---
50Hz
Yes
Yes
Yes
59.94Hz
Yes
Yes
Yes
60Hz
Yes
Yes
Yes
1920 x 1080i
*1
50Hz
Yes
Yes
Yes
59.94Hz
Yes
Yes
Yes
60Hz
Yes
Yes
Yes
1280 x 720p
50Hz
Yes
Yes
Yes
59.94Hz
Yes
Yes
Yes
60Hz
Yes
Yes
Yes
720 x 576p
50Hz
Yes
Yes
Yes
720 x 480p
59.94Hz
Yes
Yes
Yes
60Hz
Yes
Yes
Yes
640 x 480p (VGA)
59.94Hz
Yes
Yes
---
60Hz
Yes
Yes
---
720 (1440) x 576
50Hz
---
Yes
Yes
720 (1440) x 480i
59.94Hz
---
Yes
Yes
60Hz
---
Yes
Yes
DPMS
Screen
Power
consumption
*
Hsync
Vsync
ON STATE
Display
510W
Yes
Yes
STANDBY
No
display
1.0W
*2
No
Yes
SUSPEND
Yes
No
OFF STATE
No
No
DMPM
Screen
Power
consumption
*
Monitor ON
Display
510W
Active OFF
No display
1.0W
*2
MODE
Power consumption
MODE2
195 W
MODE1
310 W
OFF
510 W
Power cord: 1
CD-ROM (Utility Disk for Windows): 1
Setup manual: 1
Protection cover: 4
Handle screw (short): 4
Handle screw (short): 4
Bezel sheet (long/short): 2 each
Bezel sheet attachment instructions: 1
Cable clamp: 2
* Sharp Corporation holds authorship rights to the Utility Disk
program. Do not reproduce it without permission.
CHAPTER 1. OUTLINE OF THE PRODUCT
PN-V602 OUTLINE OF THE PRODUCT
1 – 6
1 - 10. LAYOUT OF TERMINAL PINS
■ PC/AV DVI-D INPUT TERMINAL PINS
■ RS-232C INPUT TERMINAL PINS
■ RS-232C OUTPUT TERMINAL PINS
■ PC D-SUB INPUT TERMINAL PINS
■ PC/AV DVI-D OUTPUT TERMINAL PINS
■ PC/AV HDMI INPUT TERMINAL PINS
No.
Function
No.
Function
1
TMDS data 2-
13
N.C.
2
TMDS data 2+
14
+5V
3
TMDS data 2/4 shield
15
GND
4
N.C.
16
Hot-plug detection
5
N.C.
17
TMDS data 0-
6
DDC clock
18
TMDS data 0+
7
DDC data
19
TMDS data 0/5 shield
8
N.C.
20
N.C.
9
TMDS data 1-
21
N.C.
10
TMDS data 1+
22
TMDS clock shield
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
No.
Function
No.
Function
1
N.C.
6
N.C.
2
Transmitted data
7
N.C.
3
Received data
8
N.C.
4
N.C.
9
N.C.
5
GND
No.
Function
No.
Function
1
N.C.
6
N.C.
2
Received data
7
N.C.
3
Transmitted data
8
N.C.
4
N.C.
9
N.C.
5
GND
(DVI-D 24 PIN)
(D-SUB 9 PIN)
(D-sub 9 PIN)
No.
Function
No.
Function
1
Red video signal input
9
+5V
2
Green video signal input
10
GND
3
Blue video signal input
11
N.C.
4
N.C.
12
DDC data
5
GND
13
Hsync signal input
6
GND for red video signal
14
Vsync signal input
7
GND for green video signal
15
DDC clock
8
GND for blue video signal
No.
Function
No.
Function
1
TMDS data 2-
13
N.C.
2
TMDS data 2+
14
+5V
3
TMDS data 2/4 shield
15
GND
4
N.C.
16
Hot-plug detection
5
N.C.
17
TMDS data 0-
6
DDC clock
18
TMDS data 0+
7
DDC data
19
TMDS data 0/5 shield
8
N.C.
20
N.C.
9
TMDS data 1-
21
N.C.
10
TMDS data 1+
22
TMDS clock shield
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
No.
Function
No.
Function
1
TMDS data 2+
11
TMDS clock shield
2
TMDS data 2 shield
12
TMDS clock-
3
TMDS data 2-
13
CEC
4
TMDS data 1+
14
N.C.
5
TMDS data 1 shield
15
SCL
6
TMDS data 1-
16
SDA
7
TMDS data 0+
17
DDC/CEC GND
8
TMDS data 0 shield
18
+5V
9
TMDS data 0-
19
Hot-plug detection
10
TMDS clock+
(Mini D-SUB 15 PIN)
(DVI-D 24 PIN)
(HDMI CONNECTOR)
TM
CHAPTER 1. OUTLINE OF THE PRODUCT
PN-V602 OUTLINE OF THE PRODUCT
1 – 7
2. PART NAMES AND FUNCTION
2 - 1. DISPLAY
■ FRONT VIEW
REFERENCE CHART OF POWER LAMP LIGHTING STATUS
The rear buttons if seen
from the front
2
3
4
5
6
7
8
9
1
1 LCD panel
2 INPUT button
3 MENU button
4 VOL -/Cursor control (
2 INPUT button
3 MENU button
4 VOL -/Cursor control (
) button
5 VOL +/Cursor control (
) button
6 BRIGHT -/Cursor control (
) button
7 BRIGHT +/Cursor control (
) button
8 Power button
9 Power LED
9 Power LED
Lighting Status
Status Description
Green lamp is lit.
In the power “ON” state
Green lamp is flashing.
In the input signal waiting mode
Orange lamp is lit.
In the power “OFF” state (Standby status=The power is turned off by the remote controller.)
If the Power switch is pressed when the display is in the input signal waiting mode (green lamp flashing), it also goes
into the standby status.
into the standby status.
Orange lamp is flashing.
When the Power On Delay function is activated, the power lamp blinks in orange (at about 1 second intervals).
If the setting is set to “0” (factory default), the function gets disabled and the lamp won’t blink.
The Power On Delay function enables a time delay from the turning-on of power till the display of screen, and the set-
ting can be set in 1 second increments up to 60 seconds.
ting can be set in 1 second increments up to 60 seconds.
*
This function is supposed to be set by a user. However, if it has been set by mistake, this causes the orange
lamp’s flashing.
lamp’s flashing.
Lamp is flashing alter-
nately in red and
orange.
The schedule has been set in the standby mode.
Lamp is flashing in
red
red
3green3red3green
at 1 second intervals.
(Temperature
abnomaly)
abnomaly)
The message “TEMPERATURE” blinks at 5-second intervals in the corner of the screen (Lower left corner at the fac-
tory default), and it indicates an abnormality in the internal temperature.
tory default), and it indicates an abnormality in the internal temperature.
*
It operates only when “FUNCTION” - “TEMPERATURE ALERT” is set to “OSD&LED” or “LED”.
When it is “OFF”, it does not blink. (Factory default: “LED”)
When it is “OFF”, it does not blink. (Factory default: “LED”)
*
Even when “FUNCTION” - “LED” is set to “OFF”, the setting of “TEMPERATURE ALERT” takes effect.
At the same time, the brightness is forcefully reduced by the internal processing of the LCD monitor.
If it is left in the above state and the internal temperature increases further, the monitor shuts off automatically. (Goes
If it is left in the above state and the internal temperature increases further, the monitor shuts off automatically. (Goes
into the standby mode.)
By cycling the main power or turning off and on the power by the remote controller, the screen can be restored to its original
state temporarily. However, it goes back to the standby status soon unless the cause of the temperature increase is removed.
state temporarily. However, it goes back to the standby status soon unless the cause of the temperature increase is removed.
Red lamp is flashing.
(Hardware abnomaly)
The message “STATUS” is displayed in the corner of the screen (Lower left corner at the factory default). This indi-
cates an abnormality occurring with the hardware.
Based on the sensor monitoring data, the defective board/ unit needs to be replaced.
*
It operates only when “FUNCTION” - “STATUS ALERT” is set to “OSD&LED” or “LED”.
When it is “OFF”, it does not blink. (Factory default: “LED”)
*
Even when “FUNCTION” - “LED” is set to “OFF”, the setting of “STATUS ALERT” takes effect.
CHAPTER 1. OUTLINE OF THE PRODUCT
PN-V602 OUTLINE OF THE PRODUCT
1 – 8
■ REAR VIEW
*
1
Additional input/output terminals are available by attaching the
PN-ZB02 interface expansion board (optional).
PN-ZB02 interface expansion board (optional).
*
2
This section is used to connect optional hardware for function
expansion. Offering this attachment location is not a guarantee
that future compatible hardware attachments will be released.
WHEN THE PN-ZB02 (OPTIONAL) IS ATTACHED
1
9
F
G
G
9
9
H
I
T
U V W X Y Z \ ]
[
2
3
4
5
6
7
8
J
K
L M NO P
Q
RS
When the PN-ZB02 (optional) is attached
1 INPUT button
I Optional attachment section
*2
2 MENU button
J AC input terminal
3 VOL -/Cursor control (
)
button
K Main power switch
4 VOL +/Cursor control (
)
button
L PC/AV HDMI input terminal
5 BRIGHT -/Cursor control
(
) button
M PC D-sub input terminal
6 BRIGHT +/Cursor control
(
) button
N Audio input terminal
7 Power button
O Audio output terminals
8 Power LED
P RS-232C output terminal
9 Fan/Fan cover
Q RS-232C input terminal
F Vents
R Optional terminal
*2
G Handles
S Control kit terminal
H Expansion terminal cover
*1
T PC/AV DVI-D input terminal Y Audio 2 input terminals
U PC/AV DVI-D output terminal
U PC/AV DVI-D output terminal
Z PC RGB input terminals
V LAN terminal
[ AV component input terminals
W External speaker terminals
\ AV video input terminal
X Audio 1 input terminals
] AV S-video input terminal
Click on the first or last page to see other PN-V602 (serv.man6) service manuals if exist.