Sharp PN-V602 (serv.man6) Service Manual ▷ View online
CHAPTER 4. SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES
PN-V602 SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES
4 – 20
10 - 5. SERIAL NUMBER SETTING WITH
THE DISPLAYS DAISY-CHAINED
The procedures for setting serial numbers for the daisy-chained dis-
plays are as follows.
plays are as follows.
1 ) Press the [Connection Setting] button to make the connection set-
ting.
2 ) Select the ID number of the display for the setting.
(ID002 selected in the screen below)
3 ) The subsequent procedures are the same as those for the displays
not daisy-chained.
ID
number: 1
number: 1
ID
number: 2
number: 2
ID
number: 3
number: 3
ID
number: 25
number: 25
Example
CHAPTER 4. SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES
PN-V602 SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES
4 – 21
11. USAGE TIME SETTING PROCEDURE
11 - 1. OPERATING CONDITIONS OF THE
USAGE TIME SETTING TOOL
The operating conditions of the USAGE TIME setting tool of the infor-
mation display are as follows.
■ WHEN CONNECTED TO THE INFORMATION
DISPLAY WITH AN RS-232C CABLE
The required RS-232C cable is as shown below. Connect the PC’s
COM port and the RS-232C input terminal of the display.
■ WHEN CONNECTED TO THE INFORMATION
DISPLAY WITH A LAN CABLE
Use a cross cable when connecting directly with the display, and use a
straight cable when connecting via a hub. When connecting directly, the
PC and the information display must be set properly.
When the display is already connected to a network, consult the net-
work administrator on the network setting for the PC to connect to the
work administrator on the network setting for the PC to connect to the
network.
11 - 2. START-UP OF THE USAGE TIME
SETTING TOOL
Press [Usage Time] button of the Service Tool Launcher.
11 - 3. USAGE TIME SETTING PROCEDURES
The procedures of setting usage time with use of the Usage Time Set-
ting Tool are as follows.
ting Tool are as follows.
1 ) Press [Connection Setting...] button to configure the communica-
tion settings.
2 ) Input the usage time you need to set in the field of Write Data.
It should be from “000000” to “200000.” Make sure to input a 6-digit
number.
3 ) Press [Write] button.
4 ) Press [Read] button, and confirm that the set usage time is dis-
played in the Read Data field.
11 - 4. USAGE TIME CHECK PROCEDURE
With an image displayed on the display, use the accessory remote con-
troller to enter the SERVICE MENU 1, and check the USAGE TIME on
troller to enter the SERVICE MENU 1, and check the USAGE TIME on
the column of USAGE TIME.
To enter the SERVICE MENU 1, press and hold [SIZE] button on the
remote controller for 5 sec, and press the buttons in the sequence of
remote controller for 5 sec, and press the buttons in the sequence of
[BRIGHT- (
1 )], [VOL- ( 4 )], [BRIGHT+ ( 3 )] and [VOL+ ( 2 )].
OS
n
Windows XP
n
Windows Vista
n
Windows 7
Communication
port
n
RS-232C port recognized as a COM port
(Which allows communication in 9600/19200/
(Which allows communication in 9600/19200/
38400bps.)
n
LAN
RS-232C cable
Straight cable (D-SUB 9 pin female-female)
CHAPTER 4. SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES
PN-V602 SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES
4 – 22
11 - 5. USAGE TIME SETTING WITH THE
DISPLAYS DAISY-CHAINED
The procedures for setting the Usage Time for the daisy-chained dis-
plays are as follows.
1 ) Press the [Connection Setting] button to make the connection set-
ting.
2 ) Select the ID number of the display for the setting.
(ID002 selected in the screen below)
3 ) Input the usage time you need to set in the field of Write Data.
(It should be from “000000” to “200000.” Make sure to input a 6-
digit number.)
4 ) Press the [Write] button.
5 ) Press the [Read] button, and confirm that the set usage time is dis-
played in the Read Data field.
ID
number: 1
number: 1
ID
number: 2
number: 2
ID
number: 3
number: 3
ID
number: 25
number: 25
Example
CHAPTER 4. SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES
PN-V602 SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES
4 – 23
12. MODEL NAME SETTING PROCEDURES
12 - 1. OPERATING CONDITIONS OF THE
MODEL NAME SETTING TOOL
The operating conditions of the serial number setting tool of the infor-
mation display are as follows.
■ WHEN CONNECTED TO THE INFORMATION
DISPLAY WITH AN RS-232C CABLE
The required RS-232C cable is as shown below. Connect the PC’s
COM port and the RS-232C input terminal of the display with the cable.
■ WHEN CONNECTED TO THE INFORMATION
DISPLAY WITH A LAN CABLE
Use a cross cable when connecting directly with the display, and use a
straight cable when connecting via a hub. When connecting directly, the
PC and the information display must be set properly.
PC and the information display must be set properly.
When the display is already connected to a network, consult the net-
work administrator on the network setting for the PC to connect to the
network.
12 - 2. START-UP OF THE MODEL NAME
SETTING TOOL
Press [Model Name] button of the Service Tool Launcher.
12 - 3. MODEL NAME SETTING PROCE-
DURES
The procedures of setting model names with use of the Model Name
Setting Tool are as follows.
1 ) Input the model name in the field of Write Data.
Normally, the model name has been already input at the time of
start-up. Therefore you don’t need to change it.
start-up. Therefore you don’t need to change it.
2 ) Press [Connection Setting...] button to configure the communica-
tion settings.
3 ) Press [Write] button.
4 ) Press [Read] button, and confirm that the model name is displayed
in the Read Data field.
12 - 4. MODEL NAME CHECK METHOD
Press [Display] button on the remote controller to indicate the display
information, and check the model name.
information, and check the model name.
OS
n
Windows XP
n
Windows Vista
n
Windows 7
Communication
port
n
RS-232C port recognized as a COM port
(Which can be communicate in 9600/19200/
(Which can be communicate in 9600/19200/
38400bps.)
n
LAN
RS-232C cable
Straight cable (D-SUB 9pin female - female)
Click on the first or last page to see other PN-V602 (serv.man6) service manuals if exist.