Sharp PN-U473 (serv.man2) Service Manual ▷ View online
SERVICE MANUAL
CODE: 00ZPNU553SM/E
MODEL PN-U553/U473/U423
CHAPTER 1. OUTLINE OF THE PRODUCT ······················································· 1-1
CHAPTER 2. INSTALLATION,ADJUSTMENT,SETTING ··································· 2-1
CHAPTER 3. INPORTANT INFORMATION FOR SERVICING THE DISPLAY ··· 3-1
CHAPTER 4. SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES ······· 4-1
CHAPTER 5. FIRMWARE UPDATE PROCEDURES ·········································· 5-1
CHAPTER 6. DISASSEMBLY AND ASSEMBLY ················································ 6-1
CHAPTER 7. TOROUBLESHOOTING ································································ 7-1
CHAPTER 8. HARDWARE DESVCRIPTIONS ···················································· 8-1
SHARP CORPORATION
CONTENT
.
Parts marked with “
!”
are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
INFORMATION DISPLAY
<Solder composition code of lead-free solder>
Solder composition
Solder composition code
Sn-Ag-Cu
a
Sn-Ag-Bi
Sn-Ag-Bi-Cu
b
Sn-Zn-Bi z
Sn-In-Ag-Bi i
Sn-Cu-Ni n
Sn-Ag-Sb s
Bi-Sn-Ag-P
Bi-Sn-Ag
p
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder thread. Never use conventional lead solder thread, which may cause a
breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclu-
sive-use soldering iron is recommendable.
(2) NOTE FOR SOLDERING WORK
Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering
capacity is inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land
separation or may exceed the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when
completion of soldering is confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip
after completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.
CAUTIONS
THERE IS A RISK OF EXPLOSION IF THE BATTERY
IS REPLACED BY AN INCORRECT TYPE.
PROPERLY DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
LEAD-FREE SOLDER
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
The alphabet following the LF mark shows the kind of lead-free solder.
PN-U553/U473/U423 OUTLINE OF THE PRODUCT 1 - 1
CHAPTER 1 OUTLINE OF THE PRODUCT
1. Specifications
1 – 1.Product Specifications
Model PN-U553
PN-U473
PN-U423
LCD component
55" Class [54-5/8 inch
(138.8cm) diagonal]
TFT LCD
(138.8cm) diagonal]
TFT LCD
47" Class [46-15/16
inch (119.3cm)
diagonal] TFT LCD
inch (119.3cm)
diagonal] TFT LCD
42" Class [42 inch
(106.7cm) diagonal]
TFT LCD
(106.7cm) diagonal]
TFT LCD
Max. resolution (pixels)
1920 X 1080
Max. colors
Approx. 1.06 billion colors
Pixel pitch
0.630 mm (H) × 0.630 mm (V)
0.542 mm (H) × 0.542 mm (V)
0.485 mm (H) × 0.485 mm (V)
Viewing angle
178° right/left/up/down (contrast ratio
≥ 10)
Screen active area inch (mm)
47-5/8 (W) x 26-13/16 (H)
(1209.6 x 680.4)
(1209.6 x 680.4)
40-15/16 (W) x 23 (H)
(1039.7 x 584.8)
(1039.7 x 584.8)
36-5/8 (W) x 20-5/8 (H)
(930.2 x 523.3)
(930.2 x 523.3)
Computer input signal
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75
Ω],
DisplayPort 1.1
Sync signal
Horizontal/vertical separate (TTL: positive/negative)
Video color system
NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM
Plug and play
VESA DDC2B
Power management
VESA DPMS, DVI DMPM
Input
terminals
terminals
PC/AV HDMI
x
1
PC
Mini D-sub 15 pin, 3 rows x 1
DisplayPort x 1
DVI-D 24 pin (HDCP compatible) x 1
DisplayPort x 1
DVI-D 24 pin (HDCP compatible) x 1
AV
Component: BNC (Y, Cb/Pb, Cr/Pr) x 1
*1
Composite video: BNC x 1
*1
Audio
3.5 mm mini stereo jack x 1
RCA pin (L/R) x 1
RCA pin (L/R) x 1
Serial (RS-232C)
D-sub 9 pin x 1
Output
terminals
terminals
PC
DVI-D 24 pin (HDCP compatible) x 1
Audio
RCA pin (L/R) x 1
Serial (RS-232C)
Serial (RS-232C) D-sub 9 pin x 1
LAN terminal
10 BASE-T/100 BASE-TX
Speaker output
10 W + 10 W
Power requirement
AC 100 - 240 V, 1.5 A,
50/60 Hz
50/60 Hz
AC 100 - 240 V, 1.5 A,
50/60 Hz
50/60 Hz
AC 100 - 240 V, 1.3 A,
50/60 Hz
50/60 Hz
Operating temperature
*2
41°F to 104°F(5°C to 40°C)
*3
32°F to 104°F (0°C to 40°C)
Operating humidity
20% to 80% (no condensation)
Power consumption
(input signal waiting mode
/ standby mode
(input signal waiting mode
/ standby mode
*4
)
130 W (4.5 W / 4.5 W)
130 W (4.5 W / 4.5 W)
115 W (4.5 W / 4.5 W)
Dimensions
(excluding protrusions)
inch (mm)
(excluding protrusions)
inch (mm)
Approx. 49-3/16 (W) x
2-1/4 (D) x 28-3/8 (H)
(1250 x 57 x 721)
2-1/4 (D) x 28-3/8 (H)
(1250 x 57 x 721)
Approx. 42-5/8 (W) x
2-3/16 (D) x 24-11/16 (H)
(1083 x 55 x 627)
Approx. 38-5/16 (W) x
2-1/4 (D) x 22-1/4 (H)
(973 x 57 x 565)
Weight lbs. (kg)
Approx. 55.2 (25)
Approx. 41.9 (19)
Approx. 35.3 (16)
*1 Cannot be used simultaneously.
*2 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specified by the optional equipments.
*3 Use of the monitors in temperatures below 50°F (10°C) might result in inconsistent image quality that, depending on the viewing angle,
might be noticeable along the edges of the screen. Please note that this is not a malfunction and does not affect monitor operation.
*4 When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W
PN-U553/U473/U423 OUTLINE OF THE PRODUCT 1 - 2
1 – 2.Dimensional Drawings(That the values shown are approximate values)
Unit : inch [mm]
PN-U553
PN-U473
PN-U423
When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.
SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in
serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch
(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times
or more the weight of the monitor.