Sharp PN-R703 Handy Guide ▷ View online
PN-R603/R703 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
5
-If the anti-dust solutions are not being considered ->
The dust will enter into the LCD panel through the gaps and will
cause the distorted image (see example below), and will break
down in the end.
cause the distorted image (see example below), and will break
down in the end.
The effect of dust
AS
Countermeasure against dust
-Create a completely sealed enclosure.
-The completely sealed enclosure shut off dust so it is
advantageous for installation in locations with excessive
amounts of dust, outdoor, and that may occur in salt.
advantageous for installation in locations with excessive
amounts of dust, outdoor, and that may occur in salt.
-You will need to be a combination of countermeasure against
thermal, such as the heat exchanger and the air conditioner.
thermal, such as the heat exchanger and the air conditioner.
Precautions for using anti-dust display
(2)it may raise the internal temperature for a display when using the
filter, because of raising the air resistance.
Please reduce the air resistance by increasing the area of filter, etc.
filter, because of raising the air resistance.
Please reduce the air resistance by increasing the area of filter, etc.
(3)when making the enclosure, it needs the caution whether the fan
air-breathe or exhaust the air.
air-breathe or exhaust the air.
Intake air fan:
The pressure in the enclosure is higher than out of enclosure.
Therefore, dust does not break in the housing. It is limited the size of
intake vent. And it is difficult to suck in much air(when using in dusty
area).
Therefore, dust does not break in the housing. It is limited the size of
intake vent. And it is difficult to suck in much air(when using in dusty
area).
Exhaust air fan:
The pressure in the housing is lower than out of enclosure.
Therefore, dust breaks in the housing. It has much size of intake
vent. And it is easy to control the temperature(when using in less
dusty area and severe temperature requirements).
Therefore, dust breaks in the housing. It has much size of intake
vent. And it is easy to control the temperature(when using in less
dusty area and severe temperature requirements).
※to keep the performance, please clean the filter regularly
About dust
-Fundamentally, LCD monitor is designed for indoor usage.
-When it is being used outdoor, or at dusty places, such as
railway station or close to the traffic, the solutions against dust
must be considered.
railway station or close to the traffic, the solutions against dust
must be considered.
Intake air fan
Exhaust air fan
The dust enters into the LCD panel
and causes the distorted image.
Precautions for dust
Precautions for using the filter
(1)it is possible to prolong the filter life by
using two filter and exchanging the fine
screen pre-filter.
using two filter and exchanging the fine
screen pre-filter.
-when using the anti-dust display(enclosure), please remove
the
dust with filter.
dust with filter.
PN-R603/R703 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
6
-when attaching LCD panel to protection panel, the reflection
occurs and the visibility comes down.
occurs and the visibility comes down.
-Regarding protecting the reflection non-glare, it is effective to
use the non-glare protection panel.
use the non-glare protection panel.
-Non glare coating has two methods. First method is AR coating
which decreases the reflection rate with light. Second method is
silica coating which decreases the reflection rate with scattered
reflected light.
-Silica coating is cheaper than AR coating. However, images
easily defocus and view angle is narrow with Silica coating.
Please check it before installation.
which decreases the reflection rate with light. Second method is
silica coating which decreases the reflection rate with scattered
reflected light.
-Silica coating is cheaper than AR coating. However, images
easily defocus and view angle is narrow with Silica coating.
Please check it before installation.
-Generally, when decreasing the reflection rate, image quality
comes down. Therefore, please select the suitable protection
panel in each installing location.
comes down. Therefore, please select the suitable protection
panel in each installing location.
-the closer a distance from the protection panel to the LCD panel
get the clear image. Indeed, LCD surface temperature raise.
get the clear image. Indeed, LCD surface temperature raise.
(Please keep 3 cm clearance to flow the air.)
About reflection
About dew condensation, water drops
AR coating
-Humidity condition for IDP
Range of humidity condition for IDP : From 20% to 80%(no
condensation)
condensation)
-Dew condensation and/or liquid drops will cause the
breakdown of the circuit and/or LCD panel.
Please install LCD away from condensation and liquid drops.
breakdown of the circuit and/or LCD panel.
Please install LCD away from condensation and liquid drops.
-the environment which has high possibility of condensation
The place where temperature is generally low but has
frequent warm air flow.
(Example : the place in front of the vents of radiators. When
the radiator is turn on in a cold winter morning, condensation
occurs.)
The place where temperature is generally low but has
frequent warm air flow.
(Example : the place in front of the vents of radiators. When
the radiator is turn on in a cold winter morning, condensation
occurs.)
-the environment which has high possibility of water drops
“Semi-outdoor” place where strong winded-rain(typhoon)
could potentially reach the monitor. The place which is below
the pipes inside the ceiling. (When installing in these places,
countermeasures should be taken to avoid water drops to
reach the monitors. For example, covering the LCD monitor
with box. In such a case, consideration should be given for
direction of vent.)
“Semi-outdoor” place where strong winded-rain(typhoon)
could potentially reach the monitor. The place which is below
the pipes inside the ceiling. (When installing in these places,
countermeasures should be taken to avoid water drops to
reach the monitors. For example, covering the LCD monitor
with box. In such a case, consideration should be given for
direction of vent.)
Air-breathing
from below
from below
Exhausting the
air to back
air to back
Precautions for reflection, dew condensation and water drops
PN-R603/R703 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
7
-This information display is not designed for the usage in any
places which have strong vibrations, such as inside motor
vehicles.
places which have strong vibrations, such as inside motor
vehicles.
-If the monitors will be used in the place which has the possibility
of even small vibration like railway station’s platform, shock
absorber must be considered.
of even small vibration like railway station’s platform, shock
absorber must be considered.
About vibration
About inclination
-Installing with inclination more than 20 degrees is impossible.
About power supply and voltage
-Please use certainly the attached or designated power cord.
Attached power cord is two pin for 100V level. For 200V(50/60Hz)
level, provided service parts(QACCJ1074MPPZ) (with change)
Attached power cord is two pin for 100V level. For 200V(50/60Hz)
level, provided service parts(QACCJ1074MPPZ) (with change)
-When a still image is being displayed for a long period, image
retention might occur.
retention might occur.
-Image retention can be removed by displaying motion images
or turning off the monitor. However, the longer the still image is
being displayed, the harder to remove the image retention,
therefore, the solutions mentioned above should be taken
periodically.
or turning off the monitor. However, the longer the still image is
being displayed, the harder to remove the image retention,
therefore, the solutions mentioned above should be taken
periodically.
About residual images
About expansion
-When using acrylic or polycarbonate protection panel, please be
aware of expansion due to heat or moisture absorption.
aware of expansion due to heat or moisture absorption.
Acrylic protection panel can expand about 0.4%(about 5.5 mm in
“60” inch, 6.5 mm in “70” inch) when absorbing the moisture.
“60” inch, 6.5 mm in “70” inch) when absorbing the moisture.
Please fix the protection panel not to strain it by expansion.
Precautions for vibration, inclination, voltage, residual images and expansion
PN-R603/R703 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
8
-Personal computer can control some function(ex. power
on/off) with RS-232C or LAN. Please connect RS-232C or
LAN in advance when installing the displays in height
location and so on. It helps when maintaining the displays.
on/off) with RS-232C or LAN. Please connect RS-232C or
LAN in advance when installing the displays in height
location and so on. It helps when maintaining the displays.
About RS-232C / LAN
- In analog connection, image quality is potentially influenced
by a video board or cable. And it needs all displays
adjustment when installing.
by a video board or cable. And it needs all displays
adjustment when installing.
-Please recommend digital connection(ex. HDMI, DVI,
DisplayPort connection) when customers want high quality
images. Image quality is potentially influenced by a video
board or cable. Therefore, please check the image quality
with connection in advance.
DisplayPort connection) when customers want high quality
images. Image quality is potentially influenced by a video
board or cable. Therefore, please check the image quality
with connection in advance.
-when extending the cable with optical cable, it may occur not
to read in EDID accurately. If not read in EDID accurately,
monitors cannot display accurately. Therefore, please check
the image quality with connection in advance when using
these devices.
to read in EDID accurately. If not read in EDID accurately,
monitors cannot display accurately. Therefore, please check
the image quality with connection in advance when using
these devices.
About cable
-When using the image recorder(ex. Personal computer, DVD
player) or peripheral equipment(ex. distributor, video switching
unit), please check the operation with connection in advance.
player) or peripheral equipment(ex. distributor, video switching
unit), please check the operation with connection in advance.
About peripheral equipment
Precautions for connection
About DisplayPort / DVI-D output terminal
-It is possible to output the images of DisplayPort or DVI-
I(digital signal) input to external device via DisplayPort or
DVI-D output terminal.
I(digital signal) input to external device via DisplayPort or
DVI-D output terminal.
-When outputting the encoded images by HDCP, please use
the external device with HDCP
the external device with HDCP
-It is possible to connect the monitors and display the same
images via DisplayPort input/output terminal(up to 25(for non-
HDCP-encoded content) or up to 4(for HDCP-encoded
content)).
images via DisplayPort input/output terminal(up to 25(for non-
HDCP-encoded content) or up to 4(for HDCP-encoded
content)).
- It is possible to connect the monitors and display the same
images via DVI input/output terminal(up to 5(for HDCP/non-
HDCP-encoded content)).
images via DVI input/output terminal(up to 5(for HDCP/non-
HDCP-encoded content)).
Click on the first or last page to see other PN-R703 service manuals if exist.