DOWNLOAD Sharp PN-R603 Service Manual ↓ Size: 928.53 KB | Pages: 19 in PDF or view online for FREE

Model
PN-R603
Pages
19
Size
928.53 KB
Type
PDF
Document
Handy Guide
Brand
Device
Monitor / Installation Notes
File
pn-r603.pdf
Date

Sharp PN-R603 Handy Guide ▷ View online

PN-R603/R703 Installation Guidelines <Rev1.0> February 2013 
CONFIDENTIAL 
-This information display is not designed for the usage in any 
places which have strong vibrations, such as inside motor 
vehicles. 
-If the monitors will be used in the place which has the possibility 
of even small vibration like railway station’s platform, shock 
absorber must be considered. 
About  vibration 
About inclination 
-Installing with inclination more than 20 degrees is impossible. 
About power supply and voltage  
-Please use certainly the attached or designated power cord.                       
Attached power cord is two pin for 100V level. For 200V(50/60Hz) 
level, provided service parts(QACCJ1074MPPZ) (with change) 
-When a still image is being displayed for a long period, image 
retention might occur. 
-Image retention can be removed by displaying motion images 
or turning off the monitor. However, the longer the still image is 
being displayed, the harder to remove the  image retention, 
therefore, the solutions mentioned above should be taken 
periodically. 
About residual images 
About expansion 
-When using acrylic or polycarbonate protection panel, please be 
aware of expansion due to heat or moisture absorption. 
Acrylic protection panel can expand about 0.4%(about 5.5 mm in 
“60” inch, 6.5 mm in “70” inch) when absorbing the moisture. 
Please fix the protection panel not to strain it by expansion. 
Precautions for vibration, inclination, voltage, residual images and expansion 
PN-R603/R703 Installation Guidelines <Rev1.0> February 2013 
CONFIDENTIAL 
-Personal computer can control some function(ex. power 
on/off) with RS-232C or LAN. Please connect RS-232C or 
LAN in advance when installing the displays in height 
location and so on. It helps when maintaining the displays. 
About RS-232C  /  LAN    
- In analog connection, image quality is potentially influenced 
by a video board or cable. And it needs all displays  
adjustment when installing. 
-Please recommend digital connection(ex. HDMI, DVI, 
DisplayPort connection) when customers want high quality 
images. Image quality is potentially influenced by a video 
board or cable. Therefore, please check the image quality 
with connection in advance. 
-when extending the cable with optical cable, it may occur not 
to read in EDID accurately. If not read in EDID accurately, 
monitors cannot display accurately. Therefore, please check 
the image quality with connection in advance when using 
these devices. 
About cable 
-When using the image recorder(ex. Personal computer, DVD 
player) or peripheral equipment(ex. distributor, video switching 
unit), please check the operation with connection in advance. 
About peripheral equipment  
Precautions for connection 
About DisplayPort / DVI-D output terminal 
-It is possible to output the images of DisplayPort or DVI-
I(digital signal) input to external device via DisplayPort or 
DVI-D output terminal. 
-When outputting the encoded images by HDCP, please use 
the external device with HDCP 
-It is possible to connect the monitors and display the same 
images via DisplayPort input/output terminal(up to 25(for non-
HDCP-encoded content) or up to 4(for HDCP-encoded 
content)). 
- It is possible to connect the monitors and display the same 
images via DVI input/output terminal(up to 5(for HDCP/non-
HDCP-encoded content)). 
PN-R603/R703 Installation Guidelines <Rev1.0> February 2013 
CONFIDENTIAL 
-In particular, when monitors are installed one above the 
other, the temperature raise of topside monitor cause of the 
exhaust heat from downside monitor. 
 
Regarding the countermeasure against temperature, Please 
keep the clearance in P.3. 
 
In fact, when installing multi-display, it is hard to keep the 
clearance in P.3. Therefore, please keep the temperature 
requirements to do the countermeasures as below. 
1) Reduce the surrounding temperature(using an air-
conditioner) 
2)Get down the brightness(when a brightness gets down, a 
power consumption and heat gets down) 
3)Keep much clearance between the monitors 
4)Flow the air forcibly between monitors 
  It is effective to use the spot cooler or fan in the back(when 
the monitors catch the wind, they are easily attached the 
dust). 
About thermal influence 
About expansion 
 
 
Black tape 
Please be sure the wind as much as 
possible so as to pass through, not 
choked . 
Precautions for space between displays 
(multi-display) 
If the gap between displays spoils appearance (e. g. back of 
the display can been seen through), please hide it by affixing 
black tape at the rear. 
Note: DO NOT seal the “exhalation fan and intake-nozzle” by 
black tape. 
Please attach the tape before connecting cables. 
It is necessary to check the tape periodically to make sure 
that the tape isn’t detached from the display as time goes by. 
Hiding the gap between the bezels 
 
 
 
 
 
 
The cabinet and frame of the information display is expanded 
due to heat. 
It is necessary to reserve enough space when aligning 
multiple displays. 
If  the space between displays is small, the weight  is loaded 
to LCD panel by heat expansion. 
It is necessary to increase the gap when Installing more large 
display. (Standard about 5 mm) 
PN-R603/R703 Installation Guidelines <Rev1.0> February 2013 
CONFIDENTIAL 
10 
Please reserve enough space between 
display and stick blind sheet up on the wall. 
Please reserve enough space on all sides. 
before 
after 
More space 
Current Plate 
Adding a cooling fan  to 
exhaust  the a warm air. 
Build a  slit at the front  to 
inhale the cold air into the rear. 
Precautions for space between displays 
(Case Study) 
Page of 19
Display

Click on the first or last page to see other PN-R603 service manuals if exist.