Sharp PN-R603 Handy Guide ▷ View online
PN-R603/R703 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
3
- If the temperature is too high
Electronic component’s
life time will be shortened or break down.
-If the temperature on LCD surface is too high
Monitors will break down or uniformity issue will occur
Monitors will break down or uniformity issue will occur
- If the temperature is too low Monitors will break down,
will not launch or display issue will occur.
will not launch or display issue will occur.
The thermal influence
Space requirement
Securing space at the Top/ Bottom/ Left/ Right/ Behind /
Surface of display is necessary regardless of wall-hanging
or stand type installation.
Surface of display is necessary regardless of wall-hanging
or stand type installation.
Temperature control and clearance space conditions
- Usable temperature range
※
→
0℃-40℃
- Temperature of LCD surface →
Under 60℃
Please follow these requirements when setting the display.
Refer to them and install the display according to its
requirements.
Refer to them and install the display according to its
requirements.
※: this range may change by requirements.
Heat prevention unit
(Apiste co.)
Example of fan installation
Precautions for temperature and clearance space
The effectiveness of each measure differs depending on the
environment. Please choose the best measure for respective
environment as follow.
environment. Please choose the best measure for respective
environment as follow.
- Adding a cooling fan(please use the filter and clean it
regularly.)
- Improve the ventilation by widening its space
regularly.)
- Improve the ventilation by widening its space
- Adding a heat exchanger
*this figures are without outer casing.
If you install with outer casing, requirements are changed by size/location of vent
hole, whether or not fan.
hole, whether or not fan.
Horizontal / Vertical installation
Top
20.0cm
Bottom
5.0cm
Side
5.0cm
Behind
0.7cm
Surrounding
temperature
temperature
0℃ - 40℃
PN-R603/R703 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
Countermeasure
The effect of direct sunlight
4
Precautions for the direct sunlight
-Set a sun-shade to protect the display from ultraviolet and infrared rays.
-The effect of the heat
(Even though the environmental temperature is fairly low, the temperature of the area under direct sunlight could be high.)
Monitor will break down or uniformity issue will occur.
-The effect of ultraviolet rays
LCD or color filter will deteriorate.
Please set this monitor to avoid the direct sunlight. These conditions may cause failure and/or deterioration.
PN-R603/R703 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
5
-If the anti-dust solutions are not being considered ->
The dust will enter into the LCD panel through the gaps and will
cause the distorted image (see example below), and will break
down in the end.
cause the distorted image (see example below), and will break
down in the end.
The effect of dust
AS
Countermeasure against dust
-Create a completely sealed enclosure.
-The completely sealed enclosure shut off dust so it is
advantageous for installation in locations with excessive
amounts of dust, outdoor, and that may occur in salt.
advantageous for installation in locations with excessive
amounts of dust, outdoor, and that may occur in salt.
-You will need to be a combination of countermeasure against
thermal, such as the heat exchanger and the air conditioner.
thermal, such as the heat exchanger and the air conditioner.
Precautions for using anti-dust display
(2)it may raise the internal temperature for a display when using the
filter, because of raising the air resistance.
Please reduce the air resistance by increasing the area of filter, etc.
filter, because of raising the air resistance.
Please reduce the air resistance by increasing the area of filter, etc.
(3)when making the enclosure, it needs the caution whether the fan
air-breathe or exhaust the air.
air-breathe or exhaust the air.
Intake air fan:
The pressure in the enclosure is higher than out of enclosure.
Therefore, dust does not break in the housing. It is limited the size of
intake vent. And it is difficult to suck in much air(when using in dusty
area).
Therefore, dust does not break in the housing. It is limited the size of
intake vent. And it is difficult to suck in much air(when using in dusty
area).
Exhaust air fan:
The pressure in the housing is lower than out of enclosure.
Therefore, dust breaks in the housing. It has much size of intake
vent. And it is easy to control the temperature(when using in less
dusty area and severe temperature requirements).
Therefore, dust breaks in the housing. It has much size of intake
vent. And it is easy to control the temperature(when using in less
dusty area and severe temperature requirements).
※to keep the performance, please clean the filter regularly
About dust
-Fundamentally, LCD monitor is designed for indoor usage.
-When it is being used outdoor, or at dusty places, such as
railway station or close to the traffic, the solutions against dust
must be considered.
railway station or close to the traffic, the solutions against dust
must be considered.
Intake air fan
Exhaust air fan
The dust enters into the LCD panel
and causes the distorted image.
Precautions for dust
Precautions for using the filter
(1)it is possible to prolong the filter life by
using two filter and exchanging the fine
screen pre-filter.
using two filter and exchanging the fine
screen pre-filter.
-when using the anti-dust display(enclosure), please remove
the
dust with filter.
dust with filter.
PN-R603/R703 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
6
-when attaching LCD panel to protection panel, the reflection
occurs and the visibility comes down.
occurs and the visibility comes down.
-Regarding protecting the reflection non-glare, it is effective to
use the non-glare protection panel.
use the non-glare protection panel.
-Non glare coating has two methods. First method is AR coating
which decreases the reflection rate with light. Second method is
silica coating which decreases the reflection rate with scattered
reflected light.
-Silica coating is cheaper than AR coating. However, images
easily defocus and view angle is narrow with Silica coating.
Please check it before installation.
which decreases the reflection rate with light. Second method is
silica coating which decreases the reflection rate with scattered
reflected light.
-Silica coating is cheaper than AR coating. However, images
easily defocus and view angle is narrow with Silica coating.
Please check it before installation.
-Generally, when decreasing the reflection rate, image quality
comes down. Therefore, please select the suitable protection
panel in each installing location.
comes down. Therefore, please select the suitable protection
panel in each installing location.
-the closer a distance from the protection panel to the LCD panel
get the clear image. Indeed, LCD surface temperature raise.
get the clear image. Indeed, LCD surface temperature raise.
(Please keep 3 cm clearance to flow the air.)
About reflection
About dew condensation, water drops
AR coating
-Humidity condition for IDP
Range of humidity condition for IDP : From 20% to 80%(no
condensation)
condensation)
-Dew condensation and/or liquid drops will cause the
breakdown of the circuit and/or LCD panel.
Please install LCD away from condensation and liquid drops.
breakdown of the circuit and/or LCD panel.
Please install LCD away from condensation and liquid drops.
-the environment which has high possibility of condensation
The place where temperature is generally low but has
frequent warm air flow.
(Example : the place in front of the vents of radiators. When
the radiator is turn on in a cold winter morning, condensation
occurs.)
The place where temperature is generally low but has
frequent warm air flow.
(Example : the place in front of the vents of radiators. When
the radiator is turn on in a cold winter morning, condensation
occurs.)
-the environment which has high possibility of water drops
“Semi-outdoor” place where strong winded-rain(typhoon)
could potentially reach the monitor. The place which is below
the pipes inside the ceiling. (When installing in these places,
countermeasures should be taken to avoid water drops to
reach the monitors. For example, covering the LCD monitor
with box. In such a case, consideration should be given for
direction of vent.)
“Semi-outdoor” place where strong winded-rain(typhoon)
could potentially reach the monitor. The place which is below
the pipes inside the ceiling. (When installing in these places,
countermeasures should be taken to avoid water drops to
reach the monitors. For example, covering the LCD monitor
with box. In such a case, consideration should be given for
direction of vent.)
Air-breathing
from below
from below
Exhausting the
air to back
air to back
Precautions for reflection, dew condensation and water drops