DOWNLOAD Sharp LL-T2015 Service Manual ↓ Size: 1.38 MB | Pages: 33 in PDF or view online for FREE

Model
LL-T2015
Pages
33
Size
1.38 MB
Type
PDF
Document
Service Manual
Brand
Device
Monitor
File
ll-t2015.pdf
Date

Sharp LL-T2015 Service Manual ▷ View online

LL-T2015-B/H
CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS
2 – 2
If connecting to a D-sub 15 pin 2 row Apple Power Macintosh, attach a
Macintosh conversion adapter (commercially available) to the analog
signal cable.
Note: If connecting to the Sun Ultra series, a conversion adapter (com-
mercially available) may be required.
 Digital connection
Connect the digital signal cable to the digital RGB output terminal of the
computer.
• The monitor has an input for connecting to a computer with a DVI-
compatible output connector (DVI-D24 pin or DVI-I29 pin) and UXGA
output capability.
(Depending on the type of computer to be connected, the display may
not work correctly.)
•  Use the accessory digital signal cable.
If using other commercially available digital signal cables, correct dis-
play may not be achieved.
• Paying attention to connector direction, firmly insert the signal cable
to terminal, and then tighten the screws at both sides.
Set the monitor as follows when establishing a digital connection with a
Power Mac using an ADC-DVI adapter made by Belkin. (Operation has
been checked with the Power Mac G4 M7627J/A)
•  Perform settings with the Power Mac power supply off.
1.
After connecting the power cord, turn on the monitor's main power.
2.
Press the 
e
 button and 
d
 button simultaneously, and while doing
this press the POWER button (i.e. turn the power on).
3.
Set to [ON] with the 
e d
 buttons.
•  Do not set to [ON] if you are not using a Belkin ADC-DVI adapter,
as this may result in incorrect display.
4.
Press the MENU button.
This completes setting.
 When connecting using a separately sold 2-input cable
The separately sold 2-input cable (NL-C03J) enables connection
between the DVI-I input terminal on the monitor and the two PCs.
(One analog and one digital connection.)
1. Connect the 2-input cable to the DVI-I input terminal of the monitor. 
2. Connect the accessory or commercially available analog signal
cable and the accessory digital signal cable to the 2-input cable.
• When using commercially available analog signal cable, both
ends should be mini D-sub 15 pin.
3. Connect each signal cable to the computers.
•  Paying attention to connector orientation, firmly insert the signal
cable into the PC, and then tighten the screws at both sides.
Note:
•  When using the 2-input cable, set the connecting input terminal
[INPUT-2] to [2LINES] under the MODE SELECT-2 Menu.
•  The monitor connected to the 2-input cable by analog connection
may not be automatically recognized and setup under Plug & Play.
Perform storage of setup information manually.
Macintosh conversion adapter
Digital signal cable
Digital RGB output
terminal
DVI-I input terminal
(INPUT-2)
M A C   D I G I T A L
I N P U T - 2   O N
O F F
DVI-D24 pin
2-input cable
(purchased separately)
mini D-sub15 pin
DVI-I input terminal
(INPUT-2)
Digital RGB output terminal
Digital signal cable
Analog signal cable
Analog RGB
output terminal
LL-T2015-B/H
CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS
2 – 3
1-2. Connecting the monitor to a power source
1-3. Turning the power on
1.
Turn on the main power of the monitor.
•  When switching the main power switch on and off, always wait for
an interval of at least 5 seconds. Rapid switching may result in
malfunction.
2.
Press the monitor's POWER button.
The power LED will light up orange.
3.
Turn on the computer.
When a signal is input from the computer, the power LED lights up
green, and the screen is displayed. (After power is turned on, it may
take a little time until the screen is displayed.)
•  If the input terminal to which the computer is connected has not
been selected, the screen will not be displayed. If necessary, per-
form input terminal switching. (right column)
Notes:
•  When using an analog signal, perform an automatic screen adjust-
ment under the following conditions:
– Using the monitor for the first time.
– After having changed the system settings during use.
•  Depending on the type of computer or OS, you may need to install
the monitor set-up information on your system.
•  When connecting to a notebook, if the notebook computer's screen
is set so that it is display at the same time, the MS-DOS screen
may not display properly. In this case, change the setting to display
only the LCD monitor.
1-4. Changing between input terminals
Use the INPUT button to switch between signal input terminals.
When not using a 2-input cable
When using a 2-input cable
Note: When there is no input signal, [NO SIGNAL] is displayed.
Power terminal
Power cord
AC outlet
Main power switch
ON
Turn on the
computer power
supply.
Press power button
INPUT-1
<ANALOG>
INPUT-2
 <         >
INPUT
<ANALOG> or <DIGITAL>
Analog RGB input terminal
INPUT2-A
<ANALOG>
INPUT2-D
<DIGITAL>
INPUT
INPUT-1
<ANALOG>
INPUT
INPUT
DVI-I input terminal
(analog)
DVI-I input terminal
(digital)
LL-T2015-B/H
CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS
2 – 4
1-5. Turning the power off
1.
Turn the computer off.
2.
Press the monitor's POWER button.
The Power LED will disappear.
If the monitor will not be used for a long time, turn off the main power
switch of the monitor, and remove the power plug from the outlet.
1-7. Instructions for attaching a VESA compliant arm
An arm or stand based on the VESA standard (commercially available)
can be attached to the monitor.
Procurement of the arm or stand is at the customer's discretion.
 Arms or stands able to be used
Attachments must satisfy the following.
•  Compatible with the VESA standard.
• Have a gap of 100 mm x 100 mm between the screw holes on the
section to be attached.
•  Not be likely to fall off or break off after being attached to the monitor.
 
How to attach the arm or stand
• Be careful not to over bend the cable or add extension cords as this
could lead to malfunction.
•  While following these instructions, please also refer to the installation
instructions in the operation manual included with the arm or stand.
1.
Remove the cable.
2.
Spread out a soft cloth on a suitable horizontal surface.
3.
Being careful not to damage the monitor, gently lay the monitor on it
display-side down.
4. Remove the four screws and then remove the stand from the moni-
tor.
Note:
•  The stand is specially made for use with this monitor. Once having
removed the stand, never attempt to attach it to another device.
•  Once having removed the screws, store them together with the
stand and if the stand is ever re-attached be sure to use the original
screws.
Using different screws could lead to a malfunction.
5. Attach the arm to the monitor with the four screws.
Note: The screws used to attach the arm should be M4 screws with a
length of 6 mm ~ 8 mm protruding from the surface to be
attached. Using different screws could couse the monitor to fall
off or to be internally danaged.
Caution:
Securely grasp both the display and stand, and gently tip over.
When the monitor is inclined, the stand may suddenly pop out and
cause injury.
OFF
Turn the computer off
Press power button
Caution:
Do not disassemble the stand. Parts may spring out and cause
injury.
6~8mm
Screw used to attach arm
Arm
Part of monitor to which arm is attached
LL-T2015-B/H
CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS
2 – 5
2. ADJUSTMENT
2-1. ADJUSTMENT METHOD
MENU
MENU
MENU
MENU ADJUSTMENT
AUTO
CLOCK
PHASE
H-POS
V-POS
GAMMA
MENU
GAIN
CONTROL
AUTO
BLACK LEVEL
CONTRAST
MENU
COLOR
CONTROL
COOL      STD      WARM    USER
R-CONTRAST
G-CONTRAST
B-CONTRAST
MENU MODE SELECT-2
INFOMATION
MENU
MENU
MENU
MENU MODE SELECT-1
OSD H-POSITION
1)  Resetting all adjustment values.
7)  SET/RESET of Usage Time
2)  ADJUSTMENT menu reset (Analog only)
4)  Adjusting the backlight
5)  Checking product information
8) Display adjustment
3)  Adjustment lock and lock release
While pressing
+
, turn on the power.
, turn on the power.
6) Aging
While pressing
+
, turn on the power.
simultaneously.
Press
+
While pressing
While pressing
While pressing
, turn on the power.
Adjust with
and
While pressing
, turn on the power.
(Analog only)
(Analog only)
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
(Adjust with
.)
and
x 10000
RESET
x 1000
x 100
x 10
x 1
SET/RESET USAGE TIME
USAGE TIME
ȿ
10000
ȿ
1000
ȿ
100
ȿ
10
ȿ
1
0
0
0
0
0
MANUAL
RESET
INPUT
/MODE
/MODE
/MODE
/MODE
/MODE
/MODE
/MODE
/MODE
/MODE
/MODE
/MODE
/MODE
/MODE
/MODE
/MODE
/MODE
HUE
(Impossible except display mode
"STD"  "OFFICE")
(Impossible except display mode
"STD"  "OFFICE")
OSD V-POSITION
OSD PIVOT
(Adjust with
.)
and
(Adjust with
.)
and
/MODE
/MODE
SCALING
400 LINES
(Analog only)
(Adjust with
.)
and
(Adjust with
.)
and
/MODE
/MODE
OSD LANGUAGE
(Select with
.)
/MODE
MENU
(Display)
END
MENU
OFF TIMER
INPUT-2
(Adjust with
.)
and
(Adjust with
.)
and
(When ON, Adjust with
.)
and
/MODE
/MODE
/MODE
Page of 33
Display

Click on the first or last page to see other LL-T2015 service manuals if exist.