DOWNLOAD Sharp LL-T2015 Service Manual ↓ Size: 1.38 MB | Pages: 33 in PDF or view online for FREE

Model
LL-T2015
Pages
33
Size
1.38 MB
Type
PDF
Document
Service Manual
Brand
Device
Monitor
File
ll-t2015.pdf
Date

Sharp LL-T2015 Service Manual ▷ View online

LL-T2015-B/H
OUTLINE OF THE PRODUCT, NOMENCLATURE AND FUNCTION
1 – 4
 Height adjustment, angle adjustment
Caution:
•  Be sure to hold both sides of the monitor when adjusting the view-
ing angle. Pressure from hands on the LCD panel could cause
damage.
•  Be careful not to allow your fingers to be pinched.
1) Height adjustment
Adjust to an easy to view height.
2) Angle adjustment
Adjust to an easy to view angle.
Note: Tilt of the display can be finely adjusted.
Approx. 60mm
approx. 45
approx. 45
approx. 30
approx. 5
approx. 1.0
approx. 1.0
LL-T2015-B/H
CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS
2 – 1
CHAPTER 2. CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS
1. CONNECTING THE MONITOR AND TURNING THE MONITOR ON AND OFF
Caution:
•  When connecting, ensure that both the monitor and computer are
switched off.
•  Be careful not to over bend the cable or add extension cords as this
could lead to a malfunction.
Cable storage
If necessary, excess cable can be housed in the stand.
1.
Remove the cover.
Gently pull the top of the cover towards yourself.
2.
Run cable along the back of the stand.
3. Refit the cover.
Be careful not to pinch the cable.
•  If the cover is hard to refit, do not force it.
Check whether cables are trapped.
1-1. Connecting the monitor to a computer
The accessory signal cable enables connection of two computers.
(One analog and one digital connection.)
•  The separately sold 2-input cable enables connection of two comput-
ers to the DVI-I input terminal.
• When using the 2-input cable, set the connecting input terminal
[INPUT-2] to [2LINES] under the MODE SELECT-2 Menu. 
 Analog connection
Connect the accessory analog signal cable, or separately-sold analog
signal cable (model name: NL-C02E) to the analog RGB output terminal
of the computer.
• Connect the accessory analog signal cable to the analog RGB input
terminal (INPUT-1).
• Connect the separately-sold analog signal cable (model name: NL-
C02E) to the DVI-I input terminal (INPUT-2).
• Paying attention to connector direction, firmly insert the signal cable
to terminal, and then tighten the screws at both sides.
Analog signal cable
Analog RGB output
terminal
DVI-I input terminal
(INPUT-2)
Analog RGB
input terminal
(INPUT-1)
LL-T2015-B/H
CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS
2 – 2
If connecting to a D-sub 15 pin 2 row Apple Power Macintosh, attach a
Macintosh conversion adapter (commercially available) to the analog
signal cable.
Note: If connecting to the Sun Ultra series, a conversion adapter (com-
mercially available) may be required.
 Digital connection
Connect the digital signal cable to the digital RGB output terminal of the
computer.
• The monitor has an input for connecting to a computer with a DVI-
compatible output connector (DVI-D24 pin or DVI-I29 pin) and UXGA
output capability.
(Depending on the type of computer to be connected, the display may
not work correctly.)
•  Use the accessory digital signal cable.
If using other commercially available digital signal cables, correct dis-
play may not be achieved.
• Paying attention to connector direction, firmly insert the signal cable
to terminal, and then tighten the screws at both sides.
Set the monitor as follows when establishing a digital connection with a
Power Mac using an ADC-DVI adapter made by Belkin. (Operation has
been checked with the Power Mac G4 M7627J/A)
•  Perform settings with the Power Mac power supply off.
1.
After connecting the power cord, turn on the monitor's main power.
2.
Press the 
e
 button and 
d
 button simultaneously, and while doing
this press the POWER button (i.e. turn the power on).
3.
Set to [ON] with the 
e d
 buttons.
•  Do not set to [ON] if you are not using a Belkin ADC-DVI adapter,
as this may result in incorrect display.
4.
Press the MENU button.
This completes setting.
 When connecting using a separately sold 2-input cable
The separately sold 2-input cable (NL-C03J) enables connection
between the DVI-I input terminal on the monitor and the two PCs.
(One analog and one digital connection.)
1. Connect the 2-input cable to the DVI-I input terminal of the monitor. 
2. Connect the accessory or commercially available analog signal
cable and the accessory digital signal cable to the 2-input cable.
• When using commercially available analog signal cable, both
ends should be mini D-sub 15 pin.
3. Connect each signal cable to the computers.
•  Paying attention to connector orientation, firmly insert the signal
cable into the PC, and then tighten the screws at both sides.
Note:
•  When using the 2-input cable, set the connecting input terminal
[INPUT-2] to [2LINES] under the MODE SELECT-2 Menu.
•  The monitor connected to the 2-input cable by analog connection
may not be automatically recognized and setup under Plug & Play.
Perform storage of setup information manually.
Macintosh conversion adapter
Digital signal cable
Digital RGB output
terminal
DVI-I input terminal
(INPUT-2)
M A C   D I G I T A L
I N P U T - 2   O N
O F F
DVI-D24 pin
2-input cable
(purchased separately)
mini D-sub15 pin
DVI-I input terminal
(INPUT-2)
Digital RGB output terminal
Digital signal cable
Analog signal cable
Analog RGB
output terminal
LL-T2015-B/H
CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS
2 – 3
1-2. Connecting the monitor to a power source
1-3. Turning the power on
1.
Turn on the main power of the monitor.
•  When switching the main power switch on and off, always wait for
an interval of at least 5 seconds. Rapid switching may result in
malfunction.
2.
Press the monitor's POWER button.
The power LED will light up orange.
3.
Turn on the computer.
When a signal is input from the computer, the power LED lights up
green, and the screen is displayed. (After power is turned on, it may
take a little time until the screen is displayed.)
•  If the input terminal to which the computer is connected has not
been selected, the screen will not be displayed. If necessary, per-
form input terminal switching. (right column)
Notes:
•  When using an analog signal, perform an automatic screen adjust-
ment under the following conditions:
– Using the monitor for the first time.
– After having changed the system settings during use.
•  Depending on the type of computer or OS, you may need to install
the monitor set-up information on your system.
•  When connecting to a notebook, if the notebook computer's screen
is set so that it is display at the same time, the MS-DOS screen
may not display properly. In this case, change the setting to display
only the LCD monitor.
1-4. Changing between input terminals
Use the INPUT button to switch between signal input terminals.
When not using a 2-input cable
When using a 2-input cable
Note: When there is no input signal, [NO SIGNAL] is displayed.
Power terminal
Power cord
AC outlet
Main power switch
ON
Turn on the
computer power
supply.
Press power button
INPUT-1
<ANALOG>
INPUT-2
 <         >
INPUT
<ANALOG> or <DIGITAL>
Analog RGB input terminal
INPUT2-A
<ANALOG>
INPUT2-D
<DIGITAL>
INPUT
INPUT-1
<ANALOG>
INPUT
INPUT
DVI-I input terminal
(analog)
DVI-I input terminal
(digital)
Page of 33
Display

Click on the first or last page to see other LL-T2015 service manuals if exist.