Sharp LL-T2010W (serv.man20) Service Manual ▷ View online
LL-T2010W
TROUBLE SHOOTING
4 – 4
(No)
Is D25 cathode at DC+2.5V?
Check the DC+2.5V power line and the
IC22 peripheral circuits.
IC22 peripheral circuits.
(Yes)
(Yes)
Does the whole display remain black?
Is the voltage across the fuse F3
DC+12.0V?
DC+12.0V?
(No)
Check the POWER_CTRL2 signal and
the Q4 peripheral circuits.
the Q4 peripheral circuits.
(No)
(Yes)
(Yes)
Is the display size abnormal?
Is the setup item of MODE SELECT in
the adjustment properly set?
the adjustment properly set?
Check X1, X3, IC15, the peripheral
circuits, and the software.
circuits, and the software.
(No)
Adjust properly according to the display
adjustment procedure.
adjustment procedure.
(No)
(Yes)
When the whole black display is shown
from the signal source, is there any flicker
of colors?
from the signal source, is there any flicker
of colors?
Check IC10, IC11, IC12, and the
peripheral circuits.
peripheral circuits.
(No)
(Yes)
(Yes)
Is there any deflection or flicker on the
LCD display?
LCD display?
Is the setup item of MODE SELECT in
the adjustment properly set?
the adjustment properly set?
Check IC2, IC3, IC4, and the peripheral
circuits.
circuits.
(No)
Adjust properly according to the display
adjustment procedure.
adjustment procedure.
(No)
(Yes)
(Yes)
(Yes)
Is there any abnormality in colors of the
LCD display?
LCD display?
Are the setup items of GAIN CONTROL
and WHITE BALANCE properly set?
and WHITE BALANCE properly set?
(No)
Adjust properly according to the display
adjustment procedure.
adjustment procedure.
(No)
(Yes)
Is the analog color signal output
normal? (Pins on C7, C11, C15, C18
side)
normal? (Pins on C7, C11, C15, C18
side)
(No)
Check the IC1 peripheral circuits.
(Yes)
When BRIGHT CONTRAST of a
gradation pattern, is the abnormal area
shifted?
gradation pattern, is the abnormal area
shifted?
Check the IC10, IC11, and IC12
peripheral circuits.
peripheral circuits.
(Yes)
Display the RGB color gradation of the
output data lines of RN1~Rn12 and
check the line corresponding to the
abnormal color.
output data lines of RN1~Rn12 and
check the line corresponding to the
abnormal color.
(No)
Is the positive side of C28 at DC+5V?
(No)
Check the L10 peripheral circuits.
(Yes)
Are the oscillation circuits of X1 and X3
normal? (24MHz)
normal? (24MHz)
(No)
Check X1, X2, and the IC15 peripheral
oscillating circuit.
oscillating circuit.
(Yes)
Are the clock (R94) and the signal
output of DE (R95) normal?
output of DE (R95) normal?
Check the IC17 peripheral circuits,
CN10, CN11, and the LCD module.
CN10, CN11, and the LCD module.
(No)
Execute
(Yes)
Continued from
4
2
LL-T2010W
TROUBLE SHOOTING
4 – 5
(No)
Are the adjustment contents saved after
completion of the display adjustment?
completion of the display adjustment?
Check the IC13, and IC15 peripheral
circuits.
circuits.
(Yes)
(No)
Can inputs be switched normally?
(Yes)
There is no abnormality.
Check the IC1, IC2, IC3, and IC4
peripheral circuits.
peripheral circuits.
Continued from
4
(No)
Is the positive side (no connection of part)
of C145 at H level (DC+5V)?
of C145 at H level (DC+5V)?
Check the RESET circuit in the
peripheral of IC16.
peripheral of IC16.
(Yes)
(No)
Is the output of Q7 (connected with R161)
at L level (DC+0V)?
at L level (DC+0V)?
(Yes)
Check the Q7 peripheral circuits.
(No)
Are IC15 44PIN and 33PIN at DC+5V?
(Yes)
Check the abnormal line.
(No)
Are the waveforms of RN30, R169, and
R171 outputted?
R171 outputted?
Check IC8.
(Yes)
Check RN30, R169, R171 (IC5 and IC8
control line).
control line).
5
(No)
Is the display normal with analog inputs?
First, check with analog inputs.
(Yes)
(No)
Is DC+5V applied to CN2-14PIN?
(Yes)
Check CN2 and the signal source.
(Yes)
Are the signal levels of CN2-1PIN, 2PIN,
9PIN, 10PIN, 17PIN, 18PIN 23PIN, and
24PIN changed?
9PIN, 10PIN, 17PIN, 18PIN 23PIN, and
24PIN changed?
(No)
IC8 abnormality
(No)
When resolution is changed, are the
waveforms of IC7-1PIN and 2PIN
changed normally?
waveforms of IC7-1PIN and 2PIN
changed normally?
Check IC7 and IC8.
(Yes)
Check the IC7 peripheral circuits.
PC display does not work. (Digital DVI)
LL-T2010W
TROUBLE SHOOTING
4 – 6
(No)
Is the unit connected to the analog input
CN1?
CN1?
Connect the firmware upgrade jig to the
analog input CN1.
analog input CN1.
(Yes)
(No)
Is a jig connected to CN3?
Connect the jig to CN3.
(Yes)
(No)
Are CN3-1PIN, 2PIN, and 3PIN at the
same potential?
same potential?
Check CN3 and the jig connected to
CN3.
CN3.
(Yes)
(No)
Are CN3-1PIN, 2PIN, and 3PIN at
DC+12V?
DC+12V?
Check R173 and the 12V line from the
DCJACK PWB.
DCJACK PWB.
(Yes)
(No)
Is the output of Q18 at L (DC0V)?
Check the Q18 peripheral circuits.
(Yes)
(No)
Is WRPG_SEL at DC+5V?
Check the R179~R181 peripheral
circuits.
circuits.
(Yes)
(No)
Are IC6-1PIN and 13PIN changed
properly?
properly?
(Yes)
Check IC15-31PIN, 32PIN, 33PIN, 35PIN,
and 44PIN. (IF there is no abnormality,
IC15 is defective.)
and 44PIN. (IF there is no abnormality,
IC15 is defective.)
Check the IC6 peripheral circuits.
Firmware upgrade cannot be made.
LL-T2010W
WAVE FORM
5 – 1
CHAPTER 5. WAVE FORM
Waveform measurement condition: Input each display pattern and check the waveform (timing chart).
Note:
Waveform figure
Waveform 1. XIN1 (IC15-21PIN)
Frequency: 24MHz
Display: Option
Waveform 2. XIN2 (X3's PIN on C111 side)
Frequency: 24MHz
Display: Option
Waveform 3. VSYNC (R74)
Frequency: 60Hz
Display: Option
Waveform No.
Measuring point
Name of measured waveform
Display pattern
1
IC15 21PIN
XIN1
Option
2
X3's PIN on C111 side
XIN2
Option
3
R74
VSYNC
Option
4
R76
HSYNC
Option
5
R94
LCD CLK
Option
6
R95
LCD DE
Option
7
IC17 29, 30, 41, 42PIN
LVDS CK
Option
8
RN1~RN12
LCD DATA
Pattern in every 2 lines of black and white
9
RN1~RN12
LCD DATA
Pattern in every 2 lines of black and white
10
IC8 side of C7, C11, C15
RGB OUT
Black-and-white, 16-gradation pattern
11
IC10, 11, 12: 2, 3, 5, 6, 8, 9, 11, 12,
39, 40, 42, 43, 45, 46, 48, 49PIN
39, 40, 42, 43, 45, 46, 48, 49PIN
SDRAM I/O DATA
Pattern in every 2 lines of black and white
12
IC10, 11, 12: 2, 3, 5, 6, 8, 9, 11, 12,
39, 40, 42, 43, 45, 46, 48, 49PIN
39, 40, 42, 43, 45, 46, 48, 49PIN
SDRAM I/O DATA
Pattern in every 2 lines of black and white
(1)
Use a probe of Tektonix P6139A.
(2)
Reception mode: VESA, 1600 x 1200
H: 75kHz V: 60Hz DOTCLK: 160MHz
Oscilloscope Tektronix TDS744B
Input signal
VESA 1600 x 1200
H: 75kHz V: 60Hz
DOTCLK: 160MHz
GND
2V/DIV, 20ns/DIV
2V/DIV, 20ns/DIV
GND
2V/DIV, 20ns/DIV
GND
Click on the first or last page to see other LL-T2010W (serv.man20) service manuals if exist.