DOWNLOAD Sharp LL-T2000A (serv.man11) Service Manual ↓ Size: 638.6 KB | Pages: 28 in PDF or view online for FREE

Dimensions (Units: mm)

LCD display

50 cm measured diagonally
Anti Glare Low Reflection TFT LCD module

Resolution (max.)

UXGA 1600 x 1200 pixels

Displayable colors (max.)

16.77 million colors (8 bit)

Brightness (max.)

200cd/m

2

Dot pitch

0.249(H)  0.249(V) mm

Contrast ratio

300:1

Angle of visibility

Left-right 150°; Up-down 150°

Screen display size

Horizontal 398.4 mm x Vertical 298.8 mm

Video signal

Analog RGB (0.7Vp-p) [75

Ω]

Sync signal

Separate Sync (TTL level: +/-), Sync on
Green, Composite Sync (TTL level: +/-)

Expansion compensation

Digital screening (enlargement of display to
correct VGA/SVGA/XGA/SXGA)

Plug & Play

VESA:

DDC1/DDC2B compatible

Power management

VESA:

based on DPMS

Computer signal input terminal

2 x 15 pin mini D-sub (3 rows)

USB hub function

1 upstream port, 2 downstream ports (bus-
powered hub based on USB standard Rev 1.1)

Screen tilt

Upward 0° -30°; downward 0° - 5°

Screen swivel

90° from left through right

Power supply

AC100-240V 50/60Hz (Use special AC adapter,
type NL-A51J of Sharp Corporation.)

Temperature of operating environment

5 - 35°C

Power consumption

48W max. (3.5W when in power-saving mode)
(Use special AC adapter.)

Dimensions (W x D x H, excluding rubber base)

483 mm x 218 mm x 478 mm

Weight

Approx. 10.5 kg (excluding AC adapter)

483

227

73

478

397

218

Special AC adapter
                 Approx.1.8m

            Approx. H 140 mm x D 70 mm x H 41 mm

Input connector diagram (Mini D-sub connector with 15 pins)

Number

Function

1

Red video signal input

2

Green video signal input

3

Blue video signal input

4

GND

5

GND

6

For red video signal GND

7

For green video signal GND

8

For blue video signal GND

9

N.C.

10

GND

11

GND

12

DDC data

13

For Hsync signal input

14

For Vsync signal input

15

DDC clock

640x480

640x400
720x400
800x600

1024x768

1152x864
1280x960

1280x1024

1600x1200

720x400
640x480
832x624

1024x768
1152x870

1280x1024

1600x1200

1024x768

1152x900

1280x1024

1600x1000

31.5kHz
37.9kHz
37.5kHz
43.3kHz
37.9kHz
37.9kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
53.7kHz
48.4kHz
56.5kHz
60.0kHz
68.7kHz
67.5kHz
60.0kHz
85.9kHz
64.0kHz
80.0kHz
91.1kHz
75.0kHz
31.5kHz
35.0kHz
49.7kHz
60.2kHz
68.7kHz
64.0kHz
80.0kHz
91.1kHz
75.0kHz
48.3kHz
53.6kHz
56.6kHz
61.8kHz
71.8kHz
71.7kHz
81.1kHz
68.6kHz

60.0Hz
72.0Hz
75.0Hz
85.0Hz
85.0Hz
85.0Hz
56.0Hz
60.0Hz
72.0Hz
75.0Hz
85.0Hz
60.0Hz
70.0Hz
75.0Hz
85.0Hz
75.0Hz
60.0Hz
85.0Hz
60.0Hz
75.0Hz
85.0Hz
60.0Hz
70.0Hz
66.7Hz
74.6Hz
75.0Hz
75.0Hz
60.0Hz
75.0Hz
85.0Hz
60.0Hz
60.0Hz
66.0Hz
70.0Hz
66.0Hz
76.2Hz
67.2Hz
76.0Hz
66.0Hz

25.175MHz

31.5MHz
31.5MHz
36.0MHz
31.5MHz
35.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz

56.25MHz

65.0MHz
75.0MHz

78.75MHz

94.5MHz

108.0MHz
108.0MHz
148.5MHz
108.0MHz
135.0MHz
157.5MHz
162.0MHz

28.3MHz
30.2MHz
57.3MHz
80.0MHz

100.0MHz
108.0MHz
135.0MHz
157.5MHz
162.0MHz
64.13MHz

70.4MHz

74.25MHz
94.88MHz

108.23MHz
117.01MHz
134.99MHz
135.76MHz

All are compliant only with non-interlace.

Frequencies for Power Macintosh and the Sun
Ultra series are reference values.

If the monitor is receiving timing signals that are
not compatible, [OUT OF TIMING] will appear.
Follow your computer’s instruction manual to set
the timing to be compatible with the monitor.

If the monitor is not receiving any signal (synch
signal), [NO SIGNAL] will appear.

Power management
The monitor is based on VESA DPMS (Display
Power Management Signaling).
To activate the monitor's Power Management func-
tion, both the video card and the computer must
conform to the VESA DPMS standard.

DPMS mode

Screen

Power

H-sync V-sync

consumption

ON

Display on

48W

Yes

Yes

STANDBY

No

Yes

SUSPEND Display off

Less than

Yes

No

3.5W

OFF

No

No

This monitor supports the VESA DDC (Display Data
Channel) standard.
DDC is a signal standard for carrying out Plug &
Play functions on the monitor or PC. It transfers
information such as degree of resolution between
the monitor and PC. You can use this function if your
PC is DDC compliant and if it is set so that it can
detect the Plug & Play monitor.
There are many varieties of DDC due to the differ-
ences between systems. This monitor works with
DDC1 and DDC2B.

An arm or stand based on the VESA standard
(purchased separately) can be attached to the
monitor.
Procurement of the arm or stand is at the custom-
er's discretion.

Arms or stands able to be used
Attachments must satisfy the following.
-

Compatible with the VESA standard

Have a gap of 100 mm x 100 mm between the
screw holes on the section to be attached

Not be likely to fall off or break off after being
attached to the monitor.

While following these instructions, please also
refer to the installation instructions in the
operation manual included with the arm or stand

Do not overly bend the cable or add extension
cords as this could lead to malfunction.

1. Spread out a soft cloth on a suitable horizontal

surface.

2. Being careful not to damage the monitor, gently

lay the monitor on it display-side down.

3. Remove the stand cover.

4. Remove the two screws, and remove the cover.

5. Remove the four screws and then remove the

stand from the monitor.

6. Attach the arm to the monitor with the four

screws.

(Rear view)

Stand

Stand cover

Cover

The screws used to attach the arm should be M4
screws with a length of 8 mm ~ 10 mm protruding
from the surface to be attached.
Using different screws could lead to malfunction
or may lead to the monitor falling off, internal
damaged, personal injury.

Lift one side

Screw used to attach arm

Arm
Part of monitor to which arm
is attached

8 - 10mm