DOWNLOAD Sharp LL-T1820 (serv.man11) Service Manual ↓ Size: 1.13 MB | Pages: 33 in PDF or view online for FREE

640x480

800x600

1024x768

1152x864
1280x960

1280x1024

720x400
640x480
832x624

1024x768
1152x870

1280x1024

1024x768

1152x900

1280x1024

31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
48.4kHz
56.5kHz
60.0kHz
67.5kHz
60.0kHz
64.0kHz
80.0kHz
31.5kHz
35.0kHz
49.7kHz
60.2kHz
68.7kHz
64.0kHz
80.0kHz
48.3kHz
53.6kHz
56.6kHz
61.8kHz
71.8kHz
71.7kHz
81.1kHz

60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
70Hz
75Hz
75Hz
60Hz
60Hz
75Hz
70Hz

66.7Hz
74.6Hz

75Hz
75Hz
60Hz
75Hz
60Hz
66Hz
70Hz
66Hz

76.2Hz
67.2Hz

76Hz

25.175MHz

31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
65.0MHz
75.0MHz

78.75MHz
108.0MHz
108.0MHz
108.0MHz
135.0MHz

28.3MHz
30.2MHz
57.3MHz
80.0MHz

100.0MHz
108.0MHz
135.0MHz
64.13MHz

70.4MHz

74.25MHz
94.88MHz

108.23MHz
117.01MHz
134.99MHz

Recommended resolution is 1280 x 1024.

All are compliant only with non-interlaced.

Frequencies for Power Macintosh and the Sun
Ultra series are reference values. To connect,
another adapter (purchased separately) may be
required.

If the monitor is receiving timing signals that are
not compatible, [OUT OF TIMING] will appear.
Follow your computer’s instruction manual to set
the timing so that it is compatible with the
monitor.

If the monitor is not receiving any signal (synch
signal), [NO SIGNAL] will appear.

640x480

800x600

1024x768

1152x864
1280x960

1280x1024

720x400

31.5kHz
37.9kHz
37.5kHz
37.9kHz
48.1kHz
46.9kHz
48.4kHz
56.5kHz
60.0kHz
67.5kHz
60.0kHz
64.0kHz
31.5kHz

60Hz
72Hz
75Hz
60Hz
72Hz
75Hz
60Hz
70Hz
75Hz
75Hz
60Hz
60Hz
70Hz

25.175MHz

31.5MHz
31.5MHz
40.0MHz
50.0MHz
49.5MHz
65.0MHz
75.0MHz

78.75MHz
108.0MHz
108.0MHz
108.0MHz

28.3MHz

Recommended resolution is 1280 x 1024.

All are compliant only with non-interlaced.

A computer with an output terminal conforming to
DVI (DVI-D24 pin or DVI-I29 pin) and with SXGA
output capability can be connected here.
(Depending on the type of computer to be
connected, the display may not work correctly.)

If the monitor is receiving timing signals that are
not compatible, [OUT OF TIMING] will appear.
Follow your computer's instruction manual to set
the timing so that it is compatible with the
monitor.

If the monitor is not receiving any signal (synch
signal), [NO SIGNAL] will appear.

The monitor is based on the VESA DPMS*

1

 and the

DVI DMPM*

2

 standards.

To activate the monitor's Power Management func-
tion, both the video card and the computer must
conform to the VESA DPMS standard and the DVI
DMPM standard.

*

1

 DPMS: Display Power Management Signalling

*Not using USB hub

*

2

 DMPM: Digital Monitor Power Management

*Not using USB hub

DPMS mode

Screen

Power

H-sync V-sync

consumption

ON

Display on

51W

*

Yes

Yes

STANDBY

No

Yes

SUSPEND Display off

2.9W

Yes

No

OFF

No

No

DMPM mode

Screen

Power

consumption

ON

Display on

51W

*

OFF

Display off

2.9W

No. Function

No. Function

1

TMDS data 2-

16

Hot plug detection

2

TMDS data 2+

17

TMDS data 0-

3

TMDS data 2/4 shield

18

TMDS data 0+

4

N.C.

19

TMDS data 0/5 shield

5

N.C.

20

N.C.

6

DDC clock

21

N.C.

7

DDC data

22

TMDS clock shield

8

23

TMDS clock +

9

TMDS data 1-

24

TMDS clock -

10 TMDS data 1+

C1

Analogue red image signal

11 TMDS data 1/3 shield

C2

Analogue green image signal

12

N.C.

C3

Analogue blue image signal

13

N.C.

C4

14

+5V

C5

Analogue GND

15 GND

Analogue vertically synchronised
signal

Analogue horizontally synchro-
nised signal

This monitor supports the VESA DDC (Display Data
Channel) standard.
DDC is a signal standard for carrying out Plug & Play
functions on the monitor or PC. It transfers informa-
tion such as degree of resolution between the moni-
tor and PC. You can use this function if your PC is
DDC compliant and if it is set so that it can detect
the Plug & Play monitor.
There are many varieties of DDC due to the differ-
ences between systems. This monitor works with
DDC2B.

Depending on the computer or OS, it may be neces-
sary to use the computer to operate the installation
of monitor set-up information etc. If so, follow the
steps below to install the monitor set-up information.
(Depending on the type of computer or OS, com-
mand names and methods may differ. Please follow
the computer’s own operation manual while reading
this.)

About the ICC profile
An ICC (International Color Consortium) profile is a
file that describes the color characteristics of the
LCD monitor. By using an application that works
together with an ICC profile, a high color resolution
can be realized.
-

Windows98/2000/Me/XP all use the ICC profile.

When installing Windows98/2000/Me/XP set-up
information (described below), the ICC profile is
also installed. If you would like to install  the ICC
program only, please refer to Installing the ICC
profile on page 30.

When using an ICC profile, set  [COLOR MODE]
and [WHITE BALANCE] to [STD], and set
[GAMMA], [HUE] and [SATURATION] to [0].

Installing monitor set-up information into Windows95.
This explanation assumes that the CD-ROM drive is
"D drive".
1. Load the accessory CD-ROM into the CD-ROM

drive of the computer.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced Properties], and

[Monitor], then [Change].

5. Click on [Have disk], confirm that [Copy

manufacturer's files from:] is [D:] then click [OK].

6. Confirm that the monitor details are selected, and

click [OK].

7. Check that the monitor details are displayed, then

click [Apply].

8. Click [OK], and close the window.

Installing monitor set-up information into Windows98,
and setting the monitor's ICC profile as a predeter-
mined value.
This explanation assumes that the CD-ROM drive is
"D drive".

If the "Add new Hardware Wizard" has appeared:
1. Load the accessory CD-ROM into the CD-ROM

drive of the computer.

2. Click [Next].
3. Check [Display a list of all the drivers in a

specific location, so you can select the driver you
want.], then click [Next].

4. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is
[D:], and click [OK].

5. Confirm that the monitor details are selected,

then click [Next], [Next], and [Finish]. If the "Add
New Hardware Wizard" appears, repeat the
installation commands beginning from 2 above.

If the "Add New Hardware Wizard" has not appeared:
1. Load the accessory CD-ROM into the CD-ROM

drive of the computer.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. In [Options], check [Automatically detect Plug &

Play monitors] and click on [Change].

6. Click [Next].
7. Click on [Display a list of all the drivers in a

specific location, so you can select the driver you
want.], then click [Next].

8. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is
[D:], and click [OK].

9. Confirm that the monitor details are selected,

then click [Next], [Next], and [Finish].

10. Check that the monitor details are displayed, then

click [Apply].

11. Click [OK], and close the window.

Installing monitor set-up information into Win-
dows2000, and setting the monitor's ICC profile as a
predetermined value.
This explanation assumes that the CD-ROM drive is
"D drive".
1. Load the accessory CD-ROM into the CD-ROM

drive of the computer.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. Click on [Properties], [Driver] and [Update Driver].
6. When [Upgrade Device Driver Wizard] appears,

click [Next].

7. Check [Display a list of the known drivers for this

device so that I can choose a specific driver] and
click [Next].

8. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is
[D:], and click [OK].

9. Select the monitor from the list displayed and

click [Next].

10. Click [Next], confirm that the monitor's name

appears on the screen, and click [Finish]. If [The
Digital Signature Not Found] appears, click [Yes].

11. Click on [Close].
12. Click [OK], and close the window.

Installing monitor set-up information into
WindowsMe, and setting the monitor's ICC profile as
a predetermined value.
This explanation assumes that the CD-ROM drive is
"D drive".

If the "Add new Hardware Wizard" has appeared:
1. Load the accessory CD-ROM into the CD-ROM

drive of the computer.

2. Check [Specify the location of the driver

[Advanced]] and click [Next].

3. Check [Display a list of all the drivers in a

specific location, so you can select the driver you
want.], then click [Next].

4. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is
[D:], and click [OK].

5. Select the monitor details from the list, then click

[Next], [Next], and [Finish]. If the "Add new
Hardware Wizard" appears, repeat the installation
commands beginning from 2 above.

If the "Add New Hardware Wizard" has not appeared:
1. Load the accessory CD-ROM into the CD-ROM

drive of the computer.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. In [Options], check [Automatically detect Plug &

Play monitors] and click on [Change].

6. Check [Specify the location of the driver

[Advanced]] and click [Next].

7. Check [Display a list of all the drivers in a

specific location, so you can select the driver you
want.] and click [Next].

8. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is
[D:], and click [OK].

9. Select the monitor details, then click [Next],

[Next], and [Finish].

10. Check that the monitor details are displayed, then

click [Apply].

11. Click [OK], and close the window.