DOWNLOAD Sharp LL-T17A3 (serv.man13) Service Manual ↓ Size: 668.56 KB | Pages: 26 in PDF or view online for FREE

7

5

4

3

2

1

8

9

11

6

10

12

1. MENU button ............................ This button is used to pop-up, select and close the OSD (On Screen

Display) Menu.

2.

 / MODE button ..................... When the OSD Menu is displayed:

This button is used to select menu options.

When the OSD Menu is not displayed:

This button is used to set COLOR MODE.

3.

   buttons ............................. When the OSD Menu is displayed:

These buttons are used to increase or decrease the value of a
selected option.

When the OSD Menu is not displayed:

These buttons are used to adjust backlight brightness and speaker
volume.

4. Power button ............................ Pressing this button turns the power on. (After turning the power on, it

may take a little time before the screen displays.)
Press the button again to turn the power off.

5. Power LED ............................... This LED is lit green when in use and orange when in power-saving

mode.

6. Speakers .................................. Audio entering via the monitor and the external device connected to

the monitor can be heard.

7. Audio input terminal ................. A computer’s audio output terminal can be connected here. The audio

cable included should be used.

8. Power terminal ......................... The AC adapter is connected here.
9. Analog RGB input terminal ...... The analog signal cable is connected here.The analog signal cable

included should be used.

10. Security lock anchor ................ By connecting a security lock (commercially available) to the security

lock anchor, the monitor is fixed so that it cannot be transported.
The security slot works in conjunction with Kensington Micro Saver
Security Systems.

11. Ventilation openings ................ Note: Never block the ventilation openings as this may lead to

overheating inside the monitor and result in malfunction.

12. Lock disable button .................. This button is used when folding back the display section.

02_LL-T17A3_gb.p65

9/12/2002, 6:02 PM

9

- Pressure from hands on the LCD panel could

cause damage.

- Be careful not to allow your fingers to be

pinched.

- Be careful not to place any objects on the cables.

Doing so may result in disconnection or other
problems.

Standing up the monitor
Press down on the stand and lift up the top section
of the monitor.

Folding up the monitor
1.Remove the AC adapter and the cable.
2. If carrying out adjustments to the monitor, place

it upright.

3. While pressing the rear lock disable button (1),

gently fold back the monitor (2).

(1)

(2)

Angle adjustment
Adjust to an easy to view angle.

- Do not use the monitor when tilted back beyond

approximately 20º.The monitor may fall over
leading to injury or malfunction.

Prohibited range

approx.20°

approx.5°

approx.20°

approx.5°

approx.45°

approx.45°

02_LL-T17A3_gb.p65

9/12/2002, 6:02 PM

10

- When connecting, ensure that both the monitor

and computer are switched off.

- Be careful not to overly bend the cable or add

extension cords as this could lead to a
malfunction.

- Paying attention to connector direction, firmly

insert the signal cable to terminal, and then
tighten the screws at both sides.

If connecting to a D-sub 15 pin 2 row Apple Power
Macintosh, attach a Macintosh conversion adapter
(commercially available) to the analog signal cable.

Note:
- When connecting to a notebook, if the notebook

computer's screen is set so that it is displaying at
the same time, the MS-DOS screen may not be
able to display properly. In this case, change the
settings so that only the monitor is displaying.

Analog RGB terminal
(Mini D-Sub 15 pin, 3 row)

Analog signal cable

Macintosh conversion adapter

1.Connect the AC adapter to the monitor's power

terminal.

   

2.Attach the power cord to the AC adapter and

place the power plug into the AC outlet.

   

AC adapter

Power terminal

Power cord

AC outlet

Audio input terminal

Audio cable

Audio output terminal

02_LL-T17A3_gb.p65

10/3/2002, 12:01 PM

11

1.Press the monitor's POWER button.
2.Turn on the computer.

The power LED will be lit green, and the screen
will display an image.

ON

Notes:
- If using the monitor for the first time or after

having changed the system settings during use,
perform an automatic screen adjustment.

- Depending on the computer or OS, it may be

necessary to use the computer to install monitor
set-up information. If so, follow the steps below to
install the monitor set-up information.

1. Turn the computer off.
2. Press the monitor's POWER button.

The Power LED will disappear.

OFF

If the monitor is not going to be used for a long
period of time, be sure to unplug it from the AC
outlet.

Turn on the
computer

Press power button

Press power button

Turn the
computer off

Depending on the computer or OS, it may be
necessary to use the computer to operate the
installation of monitor set-up information etc. If so,
follow the steps below to install the monitor set-up
information. (Depending on the type of computer or
OS, command names and methods may differ.
Please follow the computer’s own operation
manual while reading this.)

About the ICC profile
An ICC (International Color Consortium) profile
is a file that describes the color characteristics
of the LCD monitor. By using an application that
works together with an ICC profile, a high color
resolution can be realized.
- Windows98/2000/Me/XP all use the ICC profile.
- When installing Windows98/2000/Me/XP set-

up information (described below), the ICC
profile is also installed. If you would like to
install  the ICC program only, please refer to
Installing the ICC profile on page 14.

- When using an ICC profile, set  [COLOR

MODE] and [WHITE BALANCE] to [STD] .

Installing monitor set-up information into Win-
dows95.
This explanation assumes that the floppy disk drive
is "A drive".

1. Place the Utility Disk (provided) into the

computer's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced Properties], and

[Monitor], then [Change].

5. Click on [Have disk], confirm that [Copy

manufacturer's files from:] is [A:] then click
[OK].

6. Confirm that the monitor details are selected,

and click [OK].

7. Check that the monitor details are displayed,

then click [Apply].

8. Click [OK], and close the window.
9. Remove the Utility Disk from the A drive.

02_LL-T17A3_gb.p65

9/13/2002, 2:37 PM

12