Sharp LL-T1610W (serv.man11) Service Manual ▷ View online
4.
Click on [Settings], [Advanced] and [Monitor].
5.
In [Options], check [Automatically detect Plug & Play monitors]
and click on [Change].
and click on [Change].
6.
Click [Next].
7.
Click on [Display a list of all the drivers in a specific location, so
you can select the driver you want.], then click [Next].
you can select the driver you want.], then click [Next].
8.
When [Models] is displayed, click on [Have disk], confirm that
[Copy manufacturer’s files from:] is [A:], and click [OK].
[Copy manufacturer’s files from:] is [A:], and click [OK].
9.
Confirm that the monitor details are selected, then click [Next],
[Next], and [Finish].
[Next], and [Finish].
10. Check that the monitor details are displayed, then click [Apply].
11. Click [OK], and close the window.
12. Remove the Utility Disk from the A drive.
■
For Windows2000
Installing monitor set-up information into Windows2000, and setting
the monitor’s ICC profile as a predetermined value.
the monitor’s ICC profile as a predetermined value.
This explanation assumes that the floppy disk drive is "A drive".
1.
Place the Utility Disk (provided) into the computer’s A drive.
2.
Click on the [Start] button. From [Settings], choose [Control
Panel].
Panel].
3.
Double click on [Display].
4.
Click on [Settings], [Advanced] and [Monitor].
5.
Click on [Properties], [Driver] and [Update Driver].
6.
When [Upgrade Device Driver Wizard] appears, click [Next].
7.
Check [Display a list of the known drivers for this device so that I
can choose a specific driver] and click [Next].
can choose a specific driver] and click [Next].
8.
When [Models] is displayed, click on [Have disk], confirm that
[Copy manufacturer’s files from:] is [A:], and click [OK].
[Copy manufacturer’s files from:] is [A:], and click [OK].
9.
Select the monitor from the list displayed and click [Next].
10. Click [Next], confirm that the monitor’s name appears on the
screen, and click [Finish]. If [The Digital Signature Not Found]
appears, click [Yes].
appears, click [Yes].
11. Click on [Close].
12. Click [OK], and close the window.
13. Remove the Utility Disk from the A drive.
■
For WindowsMe
Installing monitor set-up information into WindowsMe, and setting the
monitor’s ICC profile as a predetermined value.
monitor’s ICC profile as a predetermined value.
This explanation assumes that the floppy disk drive is "A drive".
If the "Add new Hardware Wizard" has appeared:
1.
Place the Utility Disk (provided) into the computer’s A drive.
2.
Check [Specify the location of the driver [Advanced]] and click
[Next].
[Next].
3.
Check [Display a list of all the drivers in a specific location, so
you can select the driver you want.], then click [Next].
you can select the driver you want.], then click [Next].
4.
When [Models] is displayed, click on [Have disk], confirm that
[Copy manufacturer’s files from:] is [A:], and click [OK].
[Copy manufacturer’s files from:] is [A:], and click [OK].
5.
Select the monitor details from the list, then click [Next], [Next],
and [Finish]. If the "Add new Hardware Wizard" appears, repeat
the installation commands beginning from 2 above.
and [Finish]. If the "Add new Hardware Wizard" appears, repeat
the installation commands beginning from 2 above.
6.
Remove the Utility Disk from the A drive.
If the "Add New Hardware Wizard" has not appeared:
1.
Place the Utility Disk in the computer’s A drive.
2.
Click on the [Start] button. From [Settings], choose [Control
Panel].
Panel].
3.
Double click on [Display].
4.
Click on [Settings], [Advanced] and [Monitor].
5.
In [Options], check [Automatically detect Plug & Play monitors]
and click on [Change].
and click on [Change].
6.
Check [Specify the location of the driver [Advanced]] and click
[Next].
[Next].
7.
Check [Display a list of all the drivers in a specific location, so
you can select the driver you want.] and click [Next].
you can select the driver you want.] and click [Next].
8.
When [Models] is displayed, click on [Have disk], confirm that
[Copy manufacturer’s files from:] is [A:], and click [OK].
[Copy manufacturer’s files from:] is [A:], and click [OK].
9.
Select the monitor details, then click [Next], [Next], and [Finish].
10. Check that the monitor details are displayed, then click [Apply].
11. Click [OK], and close the window.
12. Remove the Utility Disk from the A drive.
Installing the ICC profile
Installing the monitor’s ICC profile. (If the set-up information has al-
ready been installed, so too has the profile, and there is no need to
install it.)
ready been installed, so too has the profile, and there is no need to
install it.)
This explanation assumes that the floppy disk drive is "A drive".
1.
Place the Utility Disk in the computer’s A drive.
2.
Click on the [Start] button. From [Settings], choose [Control
Panel].
Panel].
3.
Double click on [Display].
4.
Click on [Settings] and [Advanced].
5.
Click on [General] and from [Compatibility] select [Apply the new
display setting without restarting], then click on [Color Manage-
ment].
display setting without restarting], then click on [Color Manage-
ment].
6.
Click [Add], and select [3
1
/
2
Floppy [A:]] as the file location.
7.
Choose the color profile that you would like to install, and click
on [Add].
on [Add].
8.
Choose the profile and click on [Set As Default].
9.
Click [OK], and close the window.
10. Remove the Utility Disk from the A drive.
•
When using the ICC profile, please set the [WHITE BALANCE] to
[STD] and the [COLOR MODE] to [OFF].
[STD] and the [COLOR MODE] to [OFF].
Information about the ColorSync profile (MacOS)
About the ColorSync profile
ColorSync is the Apple Corporation’s color management system and
is a function that enables color resolution to be realized when used
with a compatible application. A ColorSync profile describes the color
characteristics of the LCD monitor.
is a function that enables color resolution to be realized when used
with a compatible application. A ColorSync profile describes the color
characteristics of the LCD monitor.
Notes:
•
This monitor’s ColorSync profile works with MacOS8.5 or
above.
above.
•
When using the ColorSync profile, please set the [WHITE
BALANCE] to [STD] and the [COLOR MODE] to [OFF].
BALANCE] to [STD] and the [COLOR MODE] to [OFF].
Setting up the ColorSync profile
Notes:
•
A floppy disk drive is necessary. In addition, it is neces-
sary to have PC Exchange or File Exchange installed in
your system.
sary to have PC Exchange or File Exchange installed in
your system.
•
Depending on the type of computer or OS, command
names and methods may differ. Please follow the com-
puter’s own operation manual while reading this.
names and methods may differ. Please follow the com-
puter’s own operation manual while reading this.
1. Place the Utility Disk (provided) into the computer’s floppy disk drive.
2. Copy the profile to be used from the Mac folder on the Utility Disk
to the ColorSync profile folder located within the system folder.
3. Using the ColorSync on the control panel, choose the profile to be used.
1-4. TURNING THE POWER OFF
1. Turn the computer off.
2. Press the monitor’s power button.
The Power LED will disappear.
If the monitor is not going to be used for a long period of time, be
sure to unplug it from the AC outlet.
sure to unplug it from the AC outlet.
1-5. CONNECTING A USB DEVICE
This monitor is manufactured to work with a bus-powered hub that is
compatible with the USB standard (based on Rev.1.1).
compatible with the USB standard (based on Rev.1.1).
Downstream (2 ports)
A USB device for currents of up to 100mA can be connected.
(Devices that exceed 100mA and USB hubs with bus-powered
specifications cannot be connected.)
(Devices that exceed 100mA and USB hubs with bus-powered
specifications cannot be connected.)
Upstream (1 port)
A USB compatible computers or USB hub with self-powered
specifications is connected here. (USB hubs with bus-powered
specifications cannot be connected.)
specifications is connected here. (USB hubs with bus-powered
specifications cannot be connected.)
Notes:
•
Before connecting, ensure that the shape of the USB ca-
ble connector is correct.
ble connector is correct.
•
For information regarding the USB function (such as set-
up) please refer to the operation manual of the computer
to be connected.
up) please refer to the operation manual of the computer
to be connected.
•
Some computers, OS and other devices may not be able
to be activated. To ascertain a certain device’s USB com-
patibility, please contact the manufacturer of the device.
to be activated. To ascertain a certain device’s USB com-
patibility, please contact the manufacturer of the device.
1. Remove the rear cover and the stand cover.
To remove them follow steps 1 and 2 of Connecting the monitor
to a power source.
to a power source.
2. Plug the USB cable (provided) into the monitor’s USB upstream port.
3. Connect the second USB cable (provided) to the computer or the
USB downstream port.
4. Plug the USB device into the monitor’s USB downstream port.
5. Replace stand cover.
6. Replace rear cover.
To replace it follow step 8 of Connecting the monitor to a power
source.
source.
2. ADJUSTMENT
2-1. BEFORE ADJUSTING THE SCREEN DISPLAY
■
About screen adjustment
The method of adjustment differs depending on whether the analog
signal or the digital signal is being used.
signal or the digital signal is being used.
For analog signal
1. First perform an automatic adjustment.
2. Perform manual adjustment where necessary.
For digital signal
The monitor can generally be used without adjustment. If necessary
perform manual adjustment.
perform manual adjustment.
Note: The OSD contents are saved even after the power is turned off.
However, if the power is turned off while the OSD menu is
displayed, the contents are not saved.
displayed, the contents are not saved.
■
Resetting all adjustment values
All adjustment values can be returned to their original ex-factory val-
ues in one command.
ues in one command.
1. Press the power button to turn off the monitor power.
2. Press the MENU button and the SELECT button simultaneously, and
while doing this press the power button (i.e. turn the monitor on).
Continue to press the button until [ALL RESET] appears on the
screen. When [ALL RESET END] appears the reset is complete.
Continue to press the button until [ALL RESET] appears on the
screen. When [ALL RESET END] appears the reset is complete.
USB upstream port
USB cable (provided)
To the computer or another
USB hub's downstream port
USB hub's downstream port
Run through hole
Run through hole
USB device
USB downstream port
1
2
Run signal cable
and USB cable
through here
and USB cable
through here
3. After the reset has been completed, press the power button to
turn off the power.
4. After a period of several seconds press the power button to turn
the monitor back on.
Notes:
•
While [ALL RESET] is displayed, the control buttons do
not function.
not function.
•
It is not possible to reset values when the adjustment lock
is in place. Remove the adjustment lock before attempting
to operate control buttons.
is in place. Remove the adjustment lock before attempting
to operate control buttons.
■
Adjustment lock function
By disabling the control buttons (i.e. setting the lock) any attempted
changes to adjusted values will be avoided.
changes to adjusted values will be avoided.
1. Press the power button to turn off the monitor power.
2. While pressing the MENU button, press the power button (i.e. turn
the power on).
Continue to press the button until the message appears on the
screen.
Continue to press the button until the message appears on the
screen.
When the menu is unlocked:
[ADJUSTENT LOCKED] will appear on the screen, and the lock
will be set.
will be set.
When the menu is locked:
[ADJUSTENT UNLOCKED] will appear on the screen, and the
lock will be removed.
lock will be removed.
Note: When the lock is in place, all buttons other than the power
button are disabled.
■
Choosing a language for messages
Messages displayed on the screen and OSD Menu contents can be
changed to the following languages.
changed to the following languages.
Dutch, English, French, German, Italian, Spanish, Swedish.
1. Press the power button to turn the monitor off.
2. Pressing the and buttons simultaneously, press the power
button (i.e. turn the monitor on).
Continue pressing the button until the Language Selection Menu
(LANGUAGE) is displayed on the screen.
(LANGUAGE) is displayed on the screen.
3. Use the SELECT button to choose a language.
4. Press the MENU button.
The setting is complete. From now, messages and adjustment
menus will be displayed in the chosen language.
menus will be displayed in the chosen language.
Note: The language selection menu disappears approximately 30
seconds after the last command has been made.
2-2. ADJUSTING THE SCREEN DISPLAY
(WHEN USING AN ANALOG SIGNAL)
(1) AUTOMATIC SCREEN ADJUSTMENT
Options in the ADJUSTMENT Menu can be adjusted automatically
(CLOCK, PHASE, H-POS V-POS).
(CLOCK, PHASE, H-POS V-POS).
Note: When setting up this monitor for the first time or after having
changed an aspect of the current system, perform an automat-
ic screen adjustment before use.
ic screen adjustment before use.
1. First display an image that makes the entire screen very bright. If
you are using Windows, you can use the Adjustment Pattern on
the accompanying Utility Disk (right column).
the accompanying Utility Disk (right column).
2. Press the MENU button.
The ADJUSTMENT Menu will be displayed.
3. Press the button.
The screen will become dark and [ADJUSTING] will be displayed.
After a few seconds the ADJUSTMENT Menu will return. (The
automatic adjustment is now complete.)
After a few seconds the ADJUSTMENT Menu will return. (The
automatic adjustment is now complete.)
4. Press the MENU button 4 times to make the OSD Menu disap-
pear.
Notes:
•
In most cases automatic adjustment is sufficient.
•
If necessary due to any of the following, manual adjust-
ments can be performed after the automatic adjustment.
ments can be performed after the automatic adjustment.
•
When further fine adjustment is needed.
•
When the computer’s video input signals are Composite
Sync or Sync On Green. (Automatic adjustments may
not be possible.)
Sync or Sync On Green. (Automatic adjustments may
not be possible.)
•
When [OUT OF ADJUST] is displayed. (When the
screen displays an entirely dark image, the automatic
screen adjustment may be disabled. When making an
automatic adjustment, be sure to either use the Adjust-
ment Pattern or try displaying an image that makes the
entire screen very bright.)
screen displays an entirely dark image, the automatic
screen adjustment may be disabled. When making an
automatic adjustment, be sure to either use the Adjust-
ment Pattern or try displaying an image that makes the
entire screen very bright.)
Opening the Adjustment Pattern (for Windows)
If you are using Windows, you can use the Adjustment Pattern (for
Windows) on the accompanying Utility Disk.
Windows) on the accompanying Utility Disk.
This explanation is for Windows 95/98/Me/2000, and assumes that
the floppy disk drive is "A drive".
the floppy disk drive is "A drive".
1. Place the Utility Disk (provided) into the computer’s A drive.
2. Open [My Computer] and select [3
1
/
2
Floppy [A:]]. If using Win-
dows 3.1, open [File Manager] and choose "A drive".
3. Double click on [Adj_uty.exe] to run the Adjustment Program. The
Adjustment Pattern will appear.
Notes:
•
After completing the adjustments, press the computer’s
[Esc] key to exit the Adjustment Program.
[Esc] key to exit the Adjustment Program.
•
If the floppy disk drive of your computer is not "A drive",
please read the below substituting the floppy disk drive
you are using in place of "A drive" or "A".
please read the below substituting the floppy disk drive
you are using in place of "A drive" or "A".
•
If your computer’s display mode is set to 65K colors, you
may see the different color levels in each color pattern or
the gray scale may look colored. (This is due to the speci-
fication of the input signal and is not a malfunction.)
may see the different color levels in each color pattern or
the gray scale may look colored. (This is due to the speci-
fication of the input signal and is not a malfunction.)
(2) MANUAL SCREEN ADJUSTMENT
Adjustments can be made using On Screen Display (OSD) Menu
provided.
provided.
1. Display an image that makes the entire screen very bright. If using
Windows, you can open and use the Adjustment Pattern on the
accompanying Utility Disk.
accompanying Utility Disk.
2. Press the MENU button.
The ADJUSTMENT Menu will be displayed.
At this point relevant menu options can be adjusted. Each time the
MENU button is pressed the next menu is selected. (ADJUST-
MENT
MENU button is pressed the next menu is selected. (ADJUST-
MENT
GAIN CONTROL
WHITE BALANCE
MODE SE-
LECT OSD Menu disappears)
Notes:
•
The OSD Menu automatically disappears approximately
30 seconds after the last command.
30 seconds after the last command.
•
This explanation is based on using the Adjustment Pattern
(for Windows) to make adjustments.
(for Windows) to make adjustments.
ADJUSTMENT Menu
MANUAL:Individual menu options are manually adjusted.
AUTO:
Every menu option is automatically adjusted.
Notes:
•
Press the button to select [AUTO].
•
To choose a menu option : SELECT button
•
To go to the next menu : MENU button
CLOCK
The figure below demonstrates how to adjust so that vertical flicker
noise is not emitted. (
noise is not emitted. (
buttons)
PHASE
The figure below demonstrates how to adjust so that horizontal flicker
noise is not emitted. (
noise is not emitted. (
buttons)
Note: Adjustments to PHASE should be made only after CLOCK has
been correctly set.
Adjustment pattern
Vertical flicker noise
Horizontal flicker noise
Click on the first or last page to see other LL-T1610W (serv.man11) service manuals if exist.