DOWNLOAD Sharp LL-171A (serv.man2) Service Manual ↓ Size: 1.15 MB | Pages: 32 in PDF or view online for FREE

Connect the accessory digital signal cable to the
digital RGB output terminal of the computer.
- The monitor has an input for connecting to a

computer with a DVI-compatible output
connector (DVI-D24 pin or DVI-I29 pin) and
SXGA output capability. (Depending on the type
of computer to be connected, the display may
not work correctly.)

- Paying attention to connector direction, firmly

insert the signal cable vertically into the
connector, and then tighten the screws at both
sides.

Set the monitor as follows when establishing a
digital connection with a Power Mac using an ADC-
DVI adapter made by Belkin. (Operation has been
checked with the Power Mac G4 M7627J/A.)
- Perform settings with the Power Mac power

supply off.

1. After connecting the power cord, turn on the

monitor's main power.

2. Press the   button and   button simultaneously,

and while doing this press the power button (i.e.
turn the power on).

O K         [ M E N U ]

MAC DIGITAL

INPUT-2

OFF

ON

3. Set to [ON] with the     buttons.

- Do not set to [ON] if you are not using a Belkin

ADC-DVI adapter, as this may result in
incorrect display.

4. Press the MENU button.

This completes setting.

Connect the accessory analog signal cable, or
separately-sold analog signal cable (model name:
NL-C02E) to the analog RGB output terminal of
the computer.
- Connect the accessory analog signal cable to

the analog RGB input terminal (INPUT-1).

- Connect the separately-sold analog signal cable

(model name: NL-C02E) to the DVI-I input
terminal (INPUT-2).

- Paying attention to connector direction, firmly

insert the signal cable vertically into the
connector, and then tighten the screws at both
sides.

If connecting to a D-sub15 pin 2 row Apple Power
Macintosh, attach a Macintosh conversion adapter
(commercially available) to the analog signal
cable.

Note:
- If connecting to the Sun Ultra series, a

conversion adapter (commercially available)
may be required.

Macintosh conversion adapter

Analog signal cable

Analog RGB output

terminal

DVI-I input terminal
(INPUT-2)

Analog RGB
input terminal
(INPUT-1)

Digital signal cable

Digital RGB output terminal

DVI-I input terminal
(INPUT-2)

171AG_gb.P65

12/4/2003, 1:14 PM

13

The separately sold 2-input cable (model name:
NL-C03J) enables connection between the DVI-I
input terminal on the monitor and the two
computers. (One analog and one digital
connection.)

1. Connect the 2-input cable to the DVI-I input

terminal of the monitor.

2. Connect the accessory or commercially

available analog signal cable and the accessory
digital signal cable to the 2-input cable.
- When using commercially available analog

signal cable, both ends should be mini D-sub
15 pin.

3. Connect each signal cable to the computers.

- Paying attention to connector direction, firmly

insert the signal cable into the connector, and
then tighten the screws at both sides.

Digital RGB
output terminal

Digital signal cable

2-input cable
(purchased
separately)

Mini D-sub15 pin

DVI-D24 pin

Analog RGB
output terminal

Analog signal
cable

DVI-I input terminal

(INPUT-2)

Notes:
- When using the 2-input cable, set the

connecting input terminal [INPUT-2] to [2LINES]
under the MODE SELECT-2 Menu. (p.22)

- The monitor connected to the 2-input cable by

analog connection may not be automatically
recognized and setup under Plug & Play.
Perform storage of setup information manually.
(p.28)

When the accessory audio cable is connected to
the audio output terminal of the computer, the
sound of the connected computer is output from
the monitor speakers. You can also use the
headphone jack of the display.

Audio output terminal

Audio cable

Audio input terminal

171AG_gb.P65

12/4/2003, 1:14 PM

14

Headphones (commercially available) can be
connected.

Note:
- When the headphones are connected, no sound

can be heard from the monitor speakers.

1. Turn on the main power of the monitor.

- When switching the main power switch on and

off, always wait for an interval of at least 5
seconds. Rapid switching may result in
malfunction.

2. Press the monitor's power button.
3. Turn on the computer.

When a signal is input from the computer, the
power LED lights up green, and the screen is
displayed. (After power is turned on, it may take
a little time until the screen is displayed.)

Note for LL-171G:
- If the input terminal to which the computer is

connected has not been selected, the screen
will not be displayed. If necessary, perform input
terminal switching. (p.16)

Notes:
- When using an analog signal, perform an

automatic screen adjustment under the following
conditions (p.19):
- Using the monitor for the first time.
- After having changed the system settings

during use.

- When using the LL-171G with a digital connection,

automatic screen adjustment is unnecessary.

- Depending on the type of computer or OS, you

may need to install the monitor set-up
information on your system. (p.28)

- When connecting to a notebook, if the notebook

computer's screen is set to display at the same
time, the MS-DOS screen may not display
properly. In this case, change the setting to
display only the LCD monitor.

Turn on the
computer power
supply.

ON

Headphones

Headphone terminal

AC outlet

Power cord

Power terminal

Main power switch

Press power button.

171AG_gb.P65

12/4/2003, 1:14 PM

15

1. Turn the computer off.
2. Press the monitor's power button.

The power LED will disappear.

If the monitor will not be used for a long time, turn
off the main power switch of the monitor, and
remove the power plug from the outlet.

Use the INPUT button to switch between signal
input terminals.

Analog RGB input terminal DVI-I input terminal

INPUT-1

<ANALOG>

INPUT-2
 <         >

INPUT

<ANALOG> or <DIGITAL>

Analog RGB input terminal

INPUT2-A

<ANALOG>

INPUT2-D

<DIGITAL>

INPUT

INPUT-1

<ANALOG>

INPUT

INPUT

Note:
- When there is no input signal, [NO SIGNAL] is

displayed.

OFF

Turn the computer
off.

Press power button.

DVI-I input terminal

(analog)

DVI-I input terminal

(digital)

171AG_gb.P65

12/4/2003, 1:14 PM

16