DOWNLOAD Sharp R-82FBSTM (serv.man4) Service Manual ↓ Size: 1.53 MB | Pages: 69 in PDF or view online for FREE

3

R-82FBSTM Op Man  18/08/2004  09:01  Page 3

4

Pacemaker: If you have a heart pacemaker,
consult your doctor or the pacemaker
manufacturer prior to oven use.

Oven Use:
• The oven is for domestic use only.
• Never operate when empty, except as directed in

the ‘Grill cooking’ section on page 13.  

• Do not leave or store anything inside the oven

when not in use.

• Never attempt to use the oven with the door

open. It is important not to force or tamper with
the door safety latches.

• Never operate the oven with any object caught in

the door.

• Do not insert fingers or objects in the holes of the

door latches or air-vent openings as this may
damage the oven and cause an electric shock.

• If water or food drops inside the air vent

openings switch the oven off immediately, unplug
it and call a SHARP approved service facility. (See
page 34).

• Never move the oven while it is operating.
• The door, outer cabinet, oven cavity, turntable,

dishes, accessories and especially the grills will
become very hot during operation. Before
cleaning make sure they are not hot. Care should
be taken to avoid touching these areas. To
prevent burns, always use thick oven gloves.

• The waveguide cover

prevents food and grease
from entering the waveguide
area where it could cause
damage.
DO NOT REMOVE THE
WAVEGUIDE COVER.

• Make sure the power supply cord is

undamaged (See “ELECTRICAL
CONNECTION” on page 6).
Do not allow the power supply cord to
run over any hot or sharp surfaces, such
as the hot air vent area at the top rear of
the oven. Any excess cord length must
be secured using the cable clip supplied
in the accessory pack. The clip should be
fixed to the top of the kitchen unit using
the screw provided (see page 5).

• The socket must be readily accessible so that it

can be easily unplugged in an emergency.

• Do not use the oven outdoors.

• Remove all packing materials including the

feature sticker (if present). Do not remove the
plastic film from the inside of the oven window
as this protects it from dirt.

R-82FBSTM Op Man  20/08/2004  08:41  Page 4

5

1. Remove all packaging and check carefully for any signs of damage.

2. If fitting the microwave oven above a conventional oven (position A) or a refrigerator (position C)

then you must check the installation instructions for that appliance to determine air intake and
exhaust requirements.
A refrigerator needs a chimney to exhaust warm air from the rear. The installation should be as
shown in fig. 1.
A conventional oven exhausts warm air from the front. The installation should be as shown in fig. 2.
If installing the microwave oven above a conventional oven, the Mylar sheet that is supplied with
the microwave oven should be fitted as shown in fig. 3. This prevents warm air from the microwave
oven from being drawn in by the conventional oven.

3. Fit the appliance into the kitchen cupboard slowly, and without force, until the front frame of the

oven seals against the front opening of the cupboard.

4. Ensure the appliance is stable and not leaning.  Ensure that a 5mm gap is kept between the

cupboard door above and the top of the frame (see fig. 4).

5. Fix the oven in position with the screws provided. The fixing points are located on the top and

bottom corners of the oven (see diagram, item 11, on page 2).

6. It is important to ensure that the installation of this product conforms to the instructions in this

operation manual and the conventional oven or refrigerator manufacturer’s installation instructions.

Position A

Position B

Position C

Conventional

oven

Refrigerator

Chimney

Cable clip

Chimney

Chimney

Position

Niche Size

Chimney

Gap Between

W

D

H

(min)

Cupboard &

Ceiling

A, B + C

562-568 x 550 x 380

45

100

Measurements in (mm)

Microwave

oven

Microwave

oven

Refrigerator

Conventional

oven

5 mm

Mylar sheet

Internal width

Ser

vice ga

p

Figure 1

Figure 2

Figure 4

Figure 3

Cable clip

Cable clip

R-82FBSTM Op Man  20/08/2004  08:41  Page 5

6

• The fuse from the cut-off plug should be

removed and the plug disposed of in a safe
manner.

• Under no circumstances should the cut-off

plug be inserted into a socket outlet as a
serious electric shock may occur.

• The plug must not be used without the fuse

cover fitted.

• If you have any doubt about your microwave

oven obtain the help of a qualified electrician.

• When replacing the plug please ensure that

you use a BSI or ASTA approved plug to
BS1363, this should be fitted with a brown
coloured 13 amp fuse approved by BSI or
ASTA to BS1362. If you have any doubt about
electrical connection seek the help of a
qualified electrician. 

To wire an appropriate plug, follow the wiring
code given in `To replace the mains plug’ on
page 34.

• Do not allow water to come into contact with

the power supply cord or plug.

• Insert the plug properly into the socket.
• Do not connect other appliances to the same

socket using an adaptor plug.

• If the power supply cord is damaged, it must

be replaced by a SHARP approved service
facility or a similarly qualified person to avoid a
hazard. 

• When removing the plug from the socket

always grip the plug, never the cord as this may
damage the power supply cord and the
connections inside the plug.

• If the plug fitted to your oven is a rewireable

type and in the event of the socket outlet in
your home not being compatible with the plug
supplied, remove the plug properly (do not cut
off). 

• If the plug fitted to your oven is a non-

rewirable type and in the event of the socket
outlet in your home not being compatible with
the plug supplied, cut-off the mains plug.

• Refit with a suitable type, observing the wiring

code given in `To replace the mains plug’ on
page 34.

• The electrical outlet should be readily accessible so that

• The socket should not be positioned behind the cupboard.
• The best position is above the cupboard, see (A).

When connecting the power supply cord to position (A) it should
be fitted to the support clips that are supplied in the fixing kit (see
diagram, item 15, on page 2).
When not connecting the power supply cord to position (A) it
should be routed under the oven. 

• Connect the appliance to a single phase 230-240V/50Hz alternating

current via a correctly installed earth socket.

• If the appliance is to be operated in a non-European country, the supply voltage,

• Before installing, tie a piece of string to the power supply cord to facilitate connection to point (A)

when the appliance is being installed.

• When inserting the appliance into the high-sided cupboard, DO NOT crush the power supply cord.

(A)

R-82FBSTM Op Man  10/11/2004  10:56  Page 6