DOWNLOAD Sharp R-32FBSTM Service Manual ↓ Size: 610.98 KB | Pages: 53 in PDF or view online for FREE

3

The appropriate indicator will flash or light up,
just above each symbol according to the
instruction. When an indicator is flashing,
press the required button (having the same
symbol) or do the necessary operation.

Stir

Turn over

Weight

Portion

Microwave power level

Cook 

R-32FBSTM Operation Manual  24/06/2004  09:03  Page 3

4

• Remove all packing materials including the

feature sticker (if present). Do not remove the
plastic film from the inside of the oven window
as this protects it from dirt.
The waveguide cover prevents food and grease
from entering the waveguide
area where it could cause
damage.
DO NOT REMOVE THE
WAVEGUIDE COVER.

• Make sure the power supply cord is

undamaged (See “ELECTRICAL
CONNECTION” on page 6).
Do not allow the power supply cord to
run over any hot or sharp surfaces, such
as the hot air vent area at the top rear of
the oven.

• The socket must be readily accessible so that it

can be easily unplugged in an emergency.

• Do not use the oven outdoors.

Oven Use:
• The oven is for domestic use only.
• Never operate the oven when empty.
• Do not leave or store anything inside the oven

when not in use.

• Never attempt to use the oven with the door

open. It is important not to force or tamper
with the door safety latches.

• Never operate the oven with any object caught

in the door.

• Do not insert fingers or objects in the holes of

the door latch openings as this may damage
the oven and cause an electric shock.

Pacemaker: If you have a heart pacemaker,
consult your doctor or the pacemaker
manufacturer prior to oven use.

R-32FBSTM Operation Manual  24/06/2004  09:03  Page 4

5

1. Remove all packaging and check carefully for any signs of damage.

2. If fitting the microwave oven above a conventional oven (position A) or a refrigerator (position C)

then you must check the installation instructions for that appliance to determine air intake and
exhaust requirements.
A refrigerator needs a chimney to exhaust warm air from the rear. The installation should be as
shown in fig. 1.
A conventional oven exhausts warm air from the front. The installation should be as shown in fig. 2.
If installing the microwave oven above a conventional oven, the Mylar sheet that is supplied with
the microwave oven should be fitted as shown in fig. 3. This prevents warm air from the microwave
oven from being drawn in by the conventional oven.

3. Fit the appliance into the kitchen cupboard slowly, and without force, until the front frame of the

oven seals against the front opening of the cupboard.

4. Ensure the appliance is stable and not leaning.  Ensure that a 5mm gap is kept between the

cupboard door above and the top of the frame (see fig. 4).

5. Fix the oven in position with the screws provided. The fixing points are located on the top and

bottom corners of the oven (see diagram, item 10, on page 2).

6. It is important to ensure that the installation of this product conforms to the instructions in this

operation manual and the conventional oven or refrigerator manufacturer’s installation instructions.

Position A

Position B

Position C

Conventional

oven

Refrigerator

Chimney

Chimney

Chimney

Position

Niche Size

Chimney

Gap Between

W

D

H

(min)

Cupboard &

Ceiling

A, B + C

560 x 550 x 380

45

100

Measurements in (mm)

Microwave

oven

Refrigerator

Microwave

oven

Conventional

oven

5 mm

Mylar sheet

Internal width

Ser

vice ga

p

Figure 1

Figure 2

Figure 4

Figure 3

R-32FBSTM Operation Manual  24/06/2004  09:03  Page 5

6

• The fuse from the cut-off plug should be

removed and the plug disposed of in a safe
manner.

• Under no circumstances should the cut-off

plug be inserted into a socket outlet as a
serious electric shock may occur.

• The plug must not be used without the fuse

cover fitted.

• If you have any doubt about your microwave

oven obtain the help of a qualified electrician.

• When replacing the plug please ensure that

you use a BSI or ASTA approved plug to
BS1363, this should be fitted with a brown
coloured 13 amp fuse approved by BSI or
ASTA to BS1362. If you have any doubt about
electrical connection seek the help of a
qualified electrician. 

To wire an appropriate plug, follow the wiring
code given in `To replace the mains plug’ on
page 25.

• Do not allow water to come into contact with

the power supply cord or plug.

• Insert the plug properly into the socket.
• Do not connect other appliances to the same

socket using an adaptor plug.

• If the power supply cord is damaged, it must

be replaced by a SHARP approved service
facility or a similarly qualified person to avoid a
hazard. 

• When removing the plug from the socket

always grip the plug, never the cord as this may
damage the power supply cord and the
connections inside the plug.

• If the plug fitted to your oven is a rewireable

type and in the event of the socket outlet in
your home not being compatible with the plug
supplied, remove the plug properly (do not cut
off). 

• If the plug fitted to your oven is a non-

rewirable type and in the event of the socket
outlet in your home not being compatible with
the plug supplied, cut-off the mains plug.

• Refit with a suitable type, observing the wiring

code given in `To replace the mains plug’ on
page 25.

• The electrical outlet should be readily accessible so

• The socket should not be positioned behind the

• The best position is above the cupboard, see (A).

When not connecting the power supply cord to position (A) it
should be removed from the support clip (see diagram, item 14,
on page 2) and routed under the oven. 

• Connect the appliance to a single phase 230-240V/50Hz

alternating current via a correctly installed earth socket.
The socket must be fused with a 

≥10A fuse.

• If the appliance is to be operated in a non-European

• Before installing, tie a piece of string to the power supply cord to facilitate connection to point (A)

when the appliance is being installed.

• When inserting the appliance into the high-sided cupboard, DO NOT crush the power supply cord.

(A)

R-32FBSTM Operation Manual  24/06/2004  09:03  Page 6