DOWNLOAD Sharp R-206 (serv.man2) Service Manual ↓ Size: 543.12 KB | Pages: 32 in PDF or view online for FREE

15

1. Disconnect oven from power supply.
2. Visually check the door and cavity face plate for dam-

age (dents, cracks, signs of arcing etc.).

Carry out any remedial work that is necessary before
operating the oven.
Do not operate the oven if any of the following conditions
exist;
1. Door does not close firmly.
2. Door hinge, support or latch hook is damaged.
3. The door gasket or seal is damaged.

4. The door is bent or warped.
5. There are defective parts in the door interlock system.
6. There are defective  parts in the microwave generating

and transmission assembly.

7. There is visible damage to the oven.

Do not operate the oven:
1. Without the RF gasket (Magnetron).
2. If the wave guide or oven cavity are not intact.
3. If the door is not closed.
4. If the outer case (cabinet) is not fitted.

Please refer to ‘OVEN PARTS, CABINET PARTS, CONTROL PANEL PARTS, DOOR PARTS’, when carrying out any
of the following removal procedures:

To remove the outer case proceed as follows.
1. Disconnect the oven from power supply.
2. Open the oven door and wedge it open.
3. Remove the eight (8) screws from rear and along the

side edge of case.

4. Slide the entire case back about 3cm to free it from

retaining clips on the cavity face plate.

5. Lift the entire case from the oven.

To prevent an electric shock, take the following
manners.
1. Before wiring,

1) Disconnect the power supply.
2) Open the door and wedge the door open.
3) Discharge the high voltage capacitor and wait for

60 seconds.

2. Don't let the wire leads touch to the following parts;

1) High voltage parts:

Magnetron, High voltage transformer, High volt-
age capacitor, High voltage fuse and High voltage
rectifier assembly.

2) Hot parts:

Oven lamp, Magnetron, High voltage transformer
and Oven cavity.

3) Sharp edge:

Bottom plate, Oven cavity, Waveguide flange,
Chassis support and other metallic plate.

4) Movable parts (to prevent a fault)

Fan blade, Fan motor, Switch.

3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector certainly until its pin

is locked. And make sure that the wire leads should
not  come off even if the wire leads is pulled.

5. To prevent an error function, connect the wire leads

correctly, referring to the Pictorial Diagram.

6. Discharge the H.V. capacitor before carrying out any

further work.

7. Do not operate the oven with the outer case removed.
N.B.; Step 1, 2 and 6 form the basis of the 3D checks.

CAUTION: DISCHARGE HIGH VOLTAGE CAPACITOR

BEFORE TOUCHING ANY OVEN COMPO-
NENT OR WIRING.

1. CARRY OUT 3D CHECKS.
2. Disconnect the wire leads (main wire harness and H.V.

fuse) from power transformer.

3. Disconnect the filament lead of power transformer from

the magnetron.

4. Disconnect the filament lead of the power transformer

from high voltage capacitor.

5. Remove the two (2) screws holding the transformer to

bottom plate from below.

6. Remove the two (2) screws holding the transformer to

bottom plate from above.

7. Remove the transformer.

16

To remove the components, proceed as follows.
1. CARRY OUT 3D CHECKS.
2. Disconnect the H.V. fuse from the power transformer.
3. Disconnect the H.V. wire of the H.V. rectifier assembly

from the magnetron.

4. Remove one (1) screw holding capacitor holder to the

oven cavity back plate.

5. Disconnect the filament lead of the power transformer

from the H.V. capacitor.

6. Remove one (1) screw holding earth side terminal of high

voltage rectifier assembly, and remove capacitor holder.

7. Disconnect all the leads and terminals of high voltage

rectifier assembly from high voltage capacitor.

8. Disconnect the H.V. fuse from the high voltage capacitor.
9. Now H.V. rectifier assembly, H.V. fuse and H.V. ca-

pacitor should be free.

CAUTION: WHEN REPLACING HIGH VOLTAGE REC-

TIFIER ASSEMBLY, ENSURE THAT THE
CATHODE (EARTH) CONNECTION IS SE-
CURELY FIXED TO THE CAPACITOR
HOLDER WITH AN EARTHING SCREW.

CAUTION: DO NOT REPLACE ONLY HIGH VOLTAGE

RECTIFIER. WHEN REPLACING IT, RE-
PLACE HIGH VOLTAGE RECTIFIER AS-
SEMBLY.

Terminal

Push

Pull down

1

2

Lever

Positive lock®

connector

Removal
1. CARRY OUT 3D CHECKS.
2. Disconnect the wire leads from the magnetron.
3. Carefully remove the three (3) screws holding the

magnetron to the waveguide flange.

4. Lift up magnetron with care so that the magnetron

antenna is not hit by any metal object around antenna.

5. Now, the magnetron is free.
Re-install
1. Re-install the magnetron to the waveguide flange with

three (3) screws.

2. Re-connect the wire leads to the magnetron. Refer to

"PICTORIAL DIAGRAM".

3. Re-install the outer case and check that the oven is

operating properly.

CAUTION: WHEN REPLACING THE MAGNETRON,

BE SURE THE R.F. GASKET IS IN PLACE
AND THE MAGNETRON MOUNTING
SCREWS ARE TIGHTENED SECURELY.

1. CARRY OUT 3D CHECKS.
2. Push the lever of positive lock

®

 connector.

3. Pull down on the positive lock

®

 connector.

CAUTION: WHEN CONNECTING THE POSITIVE

LOCK

®

 CONNECTORS TO THE TERMI-

NALS, INSTALL THE POSITIVE LOCK

®

 SO

THAT THE LEVER FACES YOU

1. CARRY OUT 3D CHECKS.
2. Disconnect the leads from the control unit and the timer

motor.

3. Remove the one (1) screw holding the chassis support

to the front plate of the oven cavity.

4. Remove the chassis support from the oven.
5. Lift up the control panel and release it from the oven

cavity.

6. Now, the control panel assembly is free.

1. CARRY OUT 3D CHECKS.
2. Remove the single (1) screw holding the green/yellow

wire to the oven cavity.

3. Disconnect the leads of the power supply cord from the

noise filter, referring to the Figure C-2 (a).

4. Release the moulding cord stopper of the power supply

cord from the square hole of the oven cavity back plate,

referring to the Figure C-2 (b).

5. Now, the power supply cord is free.

1. Insert the moulding cord stopper of power supply cord

into the square hole of the rear cabinet, referring to the
Figure C-2 (b).

17

9. Remove the O-ring and washer from the turntable

motor.

10.Now, the turntable motor is free.

1. Remove the any sharp edges on the turntable motor

cover and the bottom plate with the cutting pliers.

2. Re-install the O-ring.
3. Apply the grease (Shinetsu  silicone grease G-420 of

Sinetsu Chemical Co. Ltd. or Toray Silicone grease
SH-14 of Toray Silicone Co., Ltd.) to the O-ring and the
base of the turntable motor shaft as shown in Figure C-
4.

4. Re-install the turntable motor with the O-ring and

washer  to the oven cavity with the single (1) screw.

5. Re-connect the wire leads to the turntable motor.
6. Insert the tab of the turntable motor cover into the hole

of the bottom plate as shown in Figure C-3.

7. Re-install the turntable motor cover to the bottom plate

w i t h   o n e   ( 1 )   s c r e w   X H T S D 4 0 P 0 8 R V 0   o r
XFPSD40P08K00 as shown in Figure C-3.

2. Install the earth wire lead of power supply cord and the

earth angle to the oven cavity with one (1) screw and
tight the screw.

1. Disconnect the oven from the power supply.
2. Remove the turntable and turntable support from the

oven cavity.

3. Turn the oven over.
4. Cut the four (4) bridges holding the turntable motor

cover to the bottom plate with the cutting pliers as
shown in Figure C-3.

CAUTION: DO NOT DROP THE TURNTABLE MOTOR

COVER INTO THE OVEN AFTER CUTTING
THE BRIDGES. BECAUSE IT WILL DAM-
AGE THE WIRE LEADS OF THE MOTOR
AND IT IS DIFFICULT TO REMOVE IT OUT
OF THE OVEN.

5. Remove the turntable motor cover from the bottom

plate.

6. Disconnect the wire leads from the turntable motor.
7. Remove the single (1) screw holding the turntable

motor to the oven cavity.

8. Remove the turntable motor from the oven cavity.

3. Connect the brown and blue wire leads of power supply

cord to the noise filter correctly, referring to the Pictorial
Diagram.

Power Supply 
Cord

Oven Cavity 
Back Plate

Square 
Hole

Moulding
Cord Stopper

Power Supply Cord

Oven Cavity 
Back Plate

Screw

Green/Yelow
Wire

Brown Wire

Fuse

Blue Wire

Noise Filter

Bottom Plate

Bridges

Turnrable
Motor Cover

Tab

Hole

Cutting Pliers

Screw; 

XHTSD40P08RV0

 or

            

XFPSD40P08K00

Washer

O-ring

Base of turntable
motor shaft

Turntable motor

O-ring

Washer

Apply the 
grease hear

REMOVAL
1. CARRY OUT 3D CHECKS.
2. Disconnect the wire leads from the fan motor.
3. Remove the one (1) screw holding the chassis support

to the oven cavity front plate.

4. Remove the chassis support .
5. Release the filament lead of the power transformer and

the H.V. wire from the fan duct.

6. Remove the one (1) screw holding the light mounting

plate to the oven cavity.

7. Release the wire leads (to the oven lamp) from the hole

of the fan duct.

8. Remove the one (1) screw holding the fan duct to the

waveguide flange.

9. Release the fan motor assembly from the oven cavity.
10.Remove the fan blade from the fan motor shaft accord-

ing to the following procedure.

18

11.Hold the edge of the rotor of the fan motor by using a

pair of groove joint pliers.

12.Remove the fan blade assembly from the shaft of the

fan motor by pulling and rotating the fan blade with your
hand.

13.Now, the fan blade will be free.

14. Remove the two (2) screws holding the fan motor to

the fan duct.

15. Now, the fan motor is free.

1.

Install the fan motor to the fan duct with the two (2)
screws.

2.

Install the fan blade to the fan motor shaft according
to the following procedure.

3.

Hold the center of the bracket which supports the
shaft of the fan motor on the flat table.

4.

Apply the screw lock tight into the hole (for shaft) of
the fan blade.

5.

Install the fan blade to the shaft of fan motor by
pushing the fan blade with a small, light weight, ball
peen hammer or rubber mallet.

6.

Install the fan motor assembly to the oven cavity by
fitting the tabs of the fan duct into the holes of the oven
cavity and the waveguide flange.

7.

Re-install the light mounting plate to the oven cavity
with the one (1) screw.

8.

Insert the end of the chassis support into the slit of the
oven cavity rear cabinet.

9.

Re-install the chassis support to the oven cavity front
plate with the one (1) screw.

10. Install the filament lead and the H.V. wire into the hole

of the fan duct .

11. Re-install the wire leads (to the oven lamp) to the hole

of the fan duct.

12. Connect the wire leads to the fan motor, referring to

the pictorial diagram.

Gap

Rotor

Bracket

Stator

Groove joint pliers

Coil

Shaft

Axis

Stator

Rotor

These are the positions 
that should be pinched 
with pliers.

Shaft

Table

Center of
bracket

1. CARRY OUT 3D CHECKS.
2. Disconnect wire leads from the switches and control

panel.

3. Remove the control panel assembly from the oven

cavity front flange. Refer to chapter "CONTROL PANEL
ASSEMBLY REMOVAL".

4. Remove two (2) screws holding latch hook to oven

flange.

5. Remove latch hook assembly from oven flange.
6. To remove the monitored latch switch.
6-1. Pull out the monitored latch switch from the latch

hook, by pushing outward on the tab that is holding
the switch. But the switch will be caught by the bar of
the latch hook.

6-2. Then pull out the switch while pushing the plunger of

the switch again.

6-3. Now the  monitored latch switch is free.
7. To remove the monitor switch or latch switch.

7-1. With pushing outward on the tab that is holding the

switch, turn the switch so that the pole is an axis.

7-2. Pull out the switch from the latch hook. Do not break

the pole or tab of the latch hook.

7-3. Now the switch is free.

Re-install
1. Re-install each switch in its place. The monitored latch

switch is in the lower position and the monitor switch is
in the middle position. The latch switch is in the upper
position.

2. Re-connect wire leads to each switch. Refer to chapter

"Pictorial Diagram".

3. Secure latch hook (with two (2) mounting screws) to

oven flange.

4. Re-install the control panel assembly to the oven cavity

front flange.

5. Re-connect wire leads to the control unit. Refer to

chapter "Pictorial Diagram".