DOWNLOAD Sharp R-1900M (serv.man7) Service Manual ↓ Size: 227.15 KB | Pages: 7 in PDF or view online for FREE

R1900M

6 – 4

2. Before performing this test, make sure that the secondary interlock switches (1), (2) and the primary interlock relay RY1 are operating properly,

according to the above Switch Test Procedure. Disconnect the wire lead from the monitor switches (1), (2) (COM) terminals. Check the monitor
switches (1), (2) operation by using the ohmmeter as follows. When the door is open, the meter should indicate a closed circuit. When the monitor
switch actuator is pushed by a screw driver through the upper latch hole on the front plate of the oven cavity with the door opened (in this condition
the plunger of the monitor switch is pushed in), the meter should indicate an open circuit. If improper operation is indicated, the switch may be
defective. After testing the monitor switches, reconnect the wire lead to the monitor switch (COM) terminals and check the continuity of the monitor
circuit.

3. CARRY OUT 4R CHECKS.

1. CARRY OUT 3D CHECKS.

2. If the fuse F10 (1) or (2) is blown when the door is opened, check the primary interlock relay RY1, secondary interlock switches (1), (2) and moni-

tor switches (1), (2) according to the “TEST PROCEDURE” for those switches before replacing the blown fuse F10 (1) or (2).

CAUTION: CAUTION: BEFORE REPLACING A BLOWN FUSE F10 (1) OR (2), TEST THE PRIMARY INTERLOCK RELAY, SECONDARY INTER-

LOCK SWITCHES, DOOR SENSING SWITCH AND MONITOR SWITCHES FOR PROPER OPERATION.

3. If the fuse is blown, check the magnetron, high voltage capacitor, high voltage rectifier assembly, according to the “TEST PROCEDURE” before

replacing the blown fuse. Then replace the fuse.

4. CARRY OUT 4R CHECKS.

CARRY OUT 3D CHECKS.

If the weak point is blown, the fan motor or exhaust fan could be locked or there could be a shorts in the fan motor or exhaust fan. Check them and
replace the defective parts.

CARRY OUT 4R CHECKS.

CAUTION: Only replace weak point with the correct value replacement.

CARRY OUT 3D CHECKS.

If the weak point is blown, there could be a shorts or grounds in electrical parts or wire harness. Check them and replace the defective parts or repair
the wire harness.

CARRY OUT 4R CHECKS.

CAUTION: Only replace weak point with the correct value replacement.

1. CARRY OUT 3D CHECKS.

2. A continuity check across the temperature fuse terminals should indicate a closed circuit unless the temperature of the temperature fuse reaches

specified temperature as shown below.

Magnetron temperature 
fuse (1)

150

°C

Non resetable type

EE1

Magnetron (1) Failure:
Test magnetron (1) and fan motor.

Magnetron temperature 
fuse (2)

EE2

Magnetron (2) Failure:
Test magnetron (2) and fan motor.

Magnetron temperature 
fuse (1), (2)

EE3

Magnetron (1), (2) Failure: Test magnetron (1), (2).
Check fan motor and ventilation opening.

Oven temperature fuse

120

°C

Non resetable type

Oven shut off

Food has been burned in oven.
Temperature of oven inside is very high.

Screw Driver

Ohmmeter

Monitor switch (2)

Latch hook

Monitor switch (1)

R1900M

6 – 5

3. CARRY OUT 4R CHECKS.

CAUTION: IF THE TEMPERATURE FUSE INDICATES AN OPEN CIRCUIT AT ROOM TEMPERATURE, REPLACE TEMPERATURE FUSE.

1. CARRY OUT 3D CHECKS.

2. Disconnect the connector of the magnetron thermistor from the harness. Measure the resistance of the thermistor with an ohmmeter. Connect the

ohmmeter leads to the connector of the thermistor.

If the meter does not indicate above resistance, replace the thermistor.

3. CARRY OUT 4R CHECKS.

The exhaust thermistor can be checked by using the Special function (SF-6). Check the exhaust thermistor, referring to the pages of the Exhaust ther-
mistor check (SF-6). 

If the display shows “OH”, the exhaust thermistor is normal. If the display shows “no”, the exhaust thermistor is abnormal and it should be replaced.

1. CARRY OUT 3D CHECKS.

2. Disconnect the lead wires from the terminal the noise filter. Using an ohmmeter, check

between the terminals as described in the following table. If incorrect reading are obtained,
replace the noise filter.

3. CARRY OUT 4R CHECKS.

1. CARRY OUT 3D CHECKS.

2. Check Key unit ribbon connection before replacement.

3. If key unit ribbon connection is normal, carry out the following procedures.

4. Re-install the rear cover and the outer case (cabinet).

5. Reconnect the power supply cord.

6. The following symptoms indicate a defective key unit.

1) When touching the pads, a certain pad produces no signal at all.

2) When touching a number pad, two figures or more are displayed.

3) When touching the pads, sometimes a pad produces no signal.

7. When you can not judge if the key unit is normal or not by using the item 8 above, carry out following test procedures.

1) Disconnect the power supply cord, and then remove outer case and rear cover.

2) Open the door and block it open.

3) Discharge two high voltage capacitors.

4) Disconnect the leads to the primary of the power transformer.

5) Ensure that these leads remain isolated from other components and oven chassis by using

insulation tape.

6) Reconnect the power supply cord.

20

°C

Approx. 750K

Ω

Between source terminals

Approx. 470K

Ω

Between source (Black) and load (Black) terminals

Short circuit.

Between source (White) and load (White/Brown) terminals

Short circuit.

WEAK

POINT

NOISE FILTER

NOISE SUPPRESSION COIL

LINE CROSS CAPACITOR

1.0μF / AC 275V

DISCHARGE RESISTOR

470K 1/2W

LINE BYPASS

CAPACITOR

0.0033μF / AC 250V

LINE BYPASS

CAPACITOR

0.0033μF / AC 250V

Load

(Black)

Load

(Gray/White)

Source

(Blue)

Source

(Brown)

5

4

3

2

7

8

9

6

1

2
3
4

1

5

6

7

2
3
4

1

5

6

7

2
3
4

1

5

6

7
8

STOP

CLEAR

START

STOP

CLEAR

X2/X3

START

CN-M

CN-R

CN-Z

CUSTOM

SETTING

SET

MEMORY

EXPRESS

DEFROST

MANUAL

REHEAT

POWER

LEVEL

CN-Q

< DOOR KEY UNIT >

< KEY UNIT >

< SW UNIT >

R1900M

6 – 6

7) If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable is making good contact, verify that the door

sensing switch (stop switch) operates properly; that is the contacts are closed when the door is closed and open when the door is open. If the
door sensing switch (stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control unit and make sure the door
sensing switch is closed (either close the door or short the door sensing switch connector). Use the Key unit matrix indicated on the control
panel schematic and place a jumper wire between the pins that correspond to the STOP/CLEAR pad making momentary contact. If the control
unit responds by clearing with a beep the key unit is faulty and must be replaced. If the control unit does not respond, it is faulty and must be
replaced. If a specific pad does not respond, the above method may be used (after clearing the control unit) to determine if the control unit or
key pad is at fault.

8) For the door key unit, check the open/short and/or connection of the switch unit and the harness, too.

8. If the Key unit is defective.

1) Disconnect the power supply cord, and then remove outer case and rear cover.

2) Open the door and block it open.

3) Discharge two high voltage capacitors.

4) Replace the Key unit.

5) Reconnect all leads removed from components during testing.

6) Re-install the rear cover and the outer case (cabinet).

7) Reconnect the power supply cord after the rear cover and the outer case are installed.

8) Run the oven and check all functions.

The following symptoms indicate a defective control unit. Before replacing the control unit, perform the Key units test (Procedure O) to determine if
control unit is faulty.

Connect the power supply cord. And check for followings.

1. In connection with pads.

1) When touching the pads, a certain group of pads do not produce a signal.

2) When touching the pads, no pads produce a signal.

2. In connection with display

1) At a certain digit, all or some segments do not light up.

2) At a certain digit, brightness is low.

3) Only one indicator does not light.

4) The corresponding segments of all digits do not light up; or they continue to light up.

5) Wrong figure appears.

6) A certain group of indicators do not light up.

7) The figure of all digits flicker.

3. Other possible problems caused by defective control unit.

1) Buzzer does not sound or continues to sound.

2) Cooking is not possible.

4. If the protectors F1 and/or F2 on the control unit PWB are open, the control unit is defective. To check, carry out following procedures.

i)

Disconnect the power supply cord, and then remove outer case and rear cover.

ii) Open the door and block it open.

iii) Discharge two high voltage capacitors.

iv) Remove the control unit from the control panel, referring to “CONTROL PANEL ASSEMBLY AND CONTROL UNIT REMOVAL”.

v) Check the continuity of the protectors F1 and F2 on the control unit

1. Check the out put voltage of power unit at CN21 as follows.

i)

Disconnect the power supply cord, and then remove outer case and rear cover.

ii) Open the door and block it open.

iii) Discharge two high voltage capacitors.

iv) Disconnect the leads to the primary of the power transformer.

v) Ensure that these leads remain isolated from other components and oven chassis by using insulation tape.

vi) Check the voltage between Pin No1 and No2 of CN21.

vii) The output voltage should be approx. 24V. 

viii) If not so, the power unit is defective.

R1900M

6 – 7

2. Check the continuity of the fuse F1 and protector F21 on the power unit as follows.

i)

Disconnect the power supply cord, and then remove outer case and rear cover.

ii) Open the door and block it open.

iii) Discharge two high voltage capacitors.

iv) Remove the power unit from the oven, referring to “POWER UNIT REMOVAL”.

v) Check the continuity of the fuse F1 and the protector F21. 

vi) If they are open, the power unit is defective

1. CARRY OUT 3D CHECKS.

2. Remove the relay unit from the oven, referring to “RELAY UNIT REMOVAL”.

3. Check the continuity of the FUSE1 on the relay unit.

1) If it is open, the relay unit is defective.

4. Check the open and /or short of the transformer primary coil on the relay unit.

1) If it is open and /or short, it is defective.

5. Check the state of the relays contacts RY-1, RY-2 and RY-3 using an ohmmeter.

1) The relay contacts should be open. If not so, the relay unit is defective.

There is no test procedure for the antenna sensor.

When the error history display shows EE15, EE25 or EE35, if the antenna motors, control unit and wiring are normal, the antenna sensor may be
defective.

There is no test procedure for the microwave sensor.

When the error history display shows EE18, EE28 or EE38, if the magnetrons, control unit and wiring are normal, the microwave sensor may be
defective.