DOWNLOAD Sharp UP-5900 (serv.man8) Service Manual ↓ Size: 25.84 MB | Pages: 127 in PDF or view online for FREE

Model
UP-5900 (serv.man8)
Pages
127
Size
25.84 MB
Type
PDF
Document
Service Manual
Brand
Device
EPOS / UP5900 Service Manual
File
up-5900-sm8.pdf
Date

Sharp UP-5900 (serv.man8) Service Manual ▷ View online

CODE : 00Z
q
SERVICE MANUAL
CONTENTS
Parts marked with "
!
" are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
UP5900VSME
POS TERMINAL
 MODEL
UP-5900
      
CHAPTER 1. SPECIFICATIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
CHAPTER 2. OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
CHAPTER 3. SERVICE PRECAUTION . . . . . . . . . . . . . . . . . . . . . 3 - 1
CHAPTER 4. DIAGNOSTICS SPECIFICATIONS  . . . . . . . . . . . . . 4 - 1
CHAPTER 5. CIRCUIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . 5 - 1
CHAPTER 6. BIOS SETUP UTILITY  . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
CHAPTER 7. HDI RECOVERY PROCEDURES  . . . . . . . . . . . . . . 7 - 1
CHAPTER 8. ABOUT UTILITY SOFTWARE . . . . . . . . . . . . . . . . . 8 - 1
CHAPTER 9. CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1
CHAPTER 10. PWB LAYOUT  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1
("V/VK" version)
PARTS GUIDE
UP-5900VS
BATTERY DISPOSAL
Contains Nickel Metal Hydride Battery. Must be Disposed of Properly.
Contact Local Environmental Officials for Disposal Instructions.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
AVOID: SHORT-CIRCUITING THE BATTERY TERMINALS.
KEEP THE BATTERY AWAY FROM FIRE. 
*
 WHEN DISPOSING THE BATTERY, FOLLOW THE LOCAL 
RULES AND REGULATIONS. 
“BATTERY DISPOSAL”
THIS PRODUCT CONTAINS NICKEL-METAL HYDRIDE BATTERY.
THIS BATTERY MUST BE DISPOSED OF PROPERLY.
REMOVE THE BATTERY FROM THE PRODUCT AND CONTACT FEDERAL OR 
STATE ENVIRONMENTAL AGENCIES FOR INFORMATION ON RECYCLING AND 
DISPOSAL OPTIONS.
“TRAITEMENT DES ACCUMULATEUR USAGÉS”
CE PRODUIT CONTIENT UN ACCUMULATEUR À NICKEL MÉTAL HYDRIDE.
CET ACCUMULATEUR USAGÉ DOIT ÊTRE TRAITÉ CORRECTEMENT.
ENLEVEZ L’ ACCUMULATEUR DU PRODUIT ET PRENEZ CONTACT AVEC VOTRE 
AGENCE ENVIRONNEMENTALE LOCALE POUR DES INFORMATIONS SUR LES 
MÉTHODES DE RECYCLAGE ET DE TRAITEMENT.
UP-5900VS
SPECIFICATIONS
1 – 1
CHAPTER 1. SPECIFICATIONS
1. APPEARANCE
AC cord
Plug your terminal into a wall outlet that has a dedicated ground before
using.
Power switch
Set the power switch to the ON ( I ) position after the terminal has been
plugged in.
Power indicator
When the power switch is turned on, the power indicator will light up.
The indicator will remain on even while the display’s backlight is off.
■ 
■ 
■ 
■ 
DISPLAY
Display angle
The display may be tilted for the best viewing angle by adjusting the
rear stand.
Be sure to push the release button on the side of the rear stand when
sliding it.
Brightness control
The brightness of the illuminated display can be adjusted using the
brightness control.
Turning the control backwards darkens the display and turning it for-
wards brightens the display.
Caution: The LCD module built in this POS terminal is manufactured
with highly precise technology.
However bright pixels or blank pixels may appear. Also an
irregular color and brightness may occur depending on the
view angle. Please note that this type of phenomena is com-
mon for LCDs and may not be a malfunction.
The backlight in the display is a consumable part.
When the LCD display can no longer be adjusted and becomes darker,
you should replace the LCD module. Consult your authorized SHARP
dealer for further details.
2. RATING
Front view
Operator display
(touch panel)
Money checking
space
Brightness
control
Power indicator
Floppy disk drive
Rear view
Power switch
AC cord
Caution:
DO  NOT insert any device into this 
connector unless recommended to do.
Doing so may cause the POS terminal 
not to function properly.
DO NOT insert any object into this 
switch unless instructed to do.
Doing so may damage or delete the data.
ITEM
SPECIFICATIONS
External dimensions
11.8 (W) x 16.3 (D) x 13.5 (H) in. approximately
(298.5 (W) x 415 (D) x 342 (H) mm)
Weight
Approximately 15.5lb. (7.0 kg)
Power source
220V~240V AC 
m
 10%, 50Hz/60Hz
Power consumption
Operating : 92.5W 590mA
Working temperature
32 to 104°F (0 to 40°C)
Button
Brightness control
UP-5900VS
SPECIFICATIONS
1 – 2
3. HARDWARE
3-1. DISPLAY
3-2. KEYBOARD
1
1
1
1
 TOUCH PANEL
2
2
2
2
 POS KEY PAD
VK (U. K.) version : Option (UP-C30PK)
Except VK version : Standard
3-3. PC SYSTEM
3-4. SERIAL PORT
D-SUB 9-pin connector COM1 and COM2 are equipped.
In order to supply +5V power, CI signal and +5V power supply of COM1
and COM2 can be switched.
2 channels of RJ45 Connector COM port are equipped.
COM3 or original I/O address (COM5) can be selected as the 1 chan-
nels of RJ45 COM port.
3-5. EXPANSION SLOT
5V PCI board can built in UP-5900 instead of an ISA PC board.
It has to satisfy with power consumption as follows.
ITEM
SPECIFICATION
NOTE
Type
TFT color LCD with back light
High color (16bit)
display
Screen size
12.1" full screen
Dot size
0.0825 x RGB(W) x 0.2825(H) mm
Resolution
XGA (1024 x 768 dots)
ITEM
SPECIFICATIONS
NOTE
Type
Touch key (Analog touch panel)
Number of
key positions
4096 (W) x 4096 (H) positions
Control
Mouse emulation
ITEM
SPECIFICATION
NOTE
Type
POS rising keyboard
Number of
keys
Standard 27 keys
Numeric keys : 11 keys ( 1 to 9,0 and 00)
Capped keys : 1 6  k e y s  ( K e y  l a b e l s  a r e
locally purchased.)
Maximum 30 keys (6x5 matrix)
(Changing key layout by using
ER-11KT7/12KT7/22KT7)
Key layout
ITEM
SPECIFICATIONS
NOTE
CPU
Celeron processor
566MHz
Chip set
Intel 440BX + PIIX4e
Graphic controller
SMI Lynx3DM4+
Main memory
(for executing MS-DOS,
Application software)
Standard : 128 Mbytes
SD RAM
Max. : 256 Mbytes
adding DIMM
Video RAM
4 Mbytes
Built-in type
BIOS ROM
512 Kbytes
Flash ROM
Keyboard controller
M38813
Super I/O
PC87309
POS system controller
PSC2 : LZ9AM22
00
0
1
2
3
4
5
6
7
8
9
COM1 & COM2: D-sub 9 pin
Pin No.
Signal
Function
I/O
1
CD
Data Carrier Detect
I
2
RD
Receive Data
I
3
SD
Send Data
O
4
ER
Data Terminal Ready
O
5
SG
Signal Ground
6
DR
Data set Ready
I
7
RS
Request to Send
O
8
CS
Clear to Send
I
9
CI/+5V
Ring Indicate / +5V
I/
COM3 (or COM5): Modular jack RJ45 8 pin
Pin No.
Signal
Function
I/O
1
RS
Request to Send
O
2
ER
Data terminal Ready
I
3
SD
Send Data
O
4
SG/(+5V)
Signal Ground/(+5V)
5
SG
Signal Ground
6
RD
Receive Data
I
7
DR
Data set Ready
I
8
CS
Clear to Send
I
ITEM
SPECIFICATION
NOTE
Type
PCI bus
Power
consumption
+5V max. 0.3A
+12V max. 0.05A
5V PCI board size
Short size PC board
(Local
procurement item)
Quantity
1 slots
Page of 127
Display

Sharp UP-5900 (serv.man8) Service Manual ▷ Download

  • DOWNLOAD Sharp UP-5900 (serv.man8) Service Manual ↓ Size: 25.84 MB | Pages: 127 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp UP-5900 (serv.man8) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp UP-5900 (serv.man8) EPOS. Information contained in Sharp UP-5900 (serv.man8) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.