Sharp ER-A771 (serv.man6) Service Manual ▷ View online
ER-A771VI
MCR unit: UP-E12MR
– 4 –
6) Install the Nylon band
4
to the cables.
Fig.8
Note: If the ER-02EF2 is inserted into the lower slot, the removal of the
PWB becomes difficult. It is recommended to insert it into the
upper slot.
11. MCR unit: UP-E12MR
1) Fix the MCR angle
1
to the lower cabinet with two screws
2
.
2) Remove the three screws
3
.
3) Remove the HDD cover
4
.
4) Connect the MCR cable
5
to the MCR connector: CN12
6
on the
MAIN PWB.
5) Fit the MCR cable
5
to the slit part
A
of the bottom cabinet to
install the HDD cover
4
.
6) Fix the three screws
3
.
Fig.9
12. Drawer box unit: ER-03DW/04DW
/05DW
1) Connect the drawer cable
1
to the drawer connector
2
.
2) Fix the earth wire
3
from drawer box unit with the screw
4
.
Fig.10
3) Install the ferrite Core
5
to the drawer cable.
4) Fix the drawer cable
1
with the cable holder
6
, and tighten the
screw
7
on the back of lower cabinet
A
or
B
.
13. Customer display: UP-I16DP
1) Remove the rear display cover.
2) Change the display filter.
Fig.11
EFT cable
1
2
RS232 cable
ER-A7RS2
ER-02EF2
RS232 cable
3
3
4
4
3
4
3
4
2
1
5
A
6
1 turn
ER-A771VI
Remote display: UP-P16DP
– 5 –
3) Hitch the UP-I16DP on the two latches
A
of the lower cabinet.
4) Raise the UP-I16DP toward you and put the two latches
B
into the
chassis.
Fig.12
Caution: When installing the UP-I16DP on the lower cabinet, align it
with the line of the lower cabinet. Make sure it settles inside
the latch.
5) Make sure the display cable passes under it.
6) Connect to the display cable to the display connector.
Fig.13
7) Install the core on the cable and secure the cable with the clamp.
8) Install the display cover.
14. Remote display: UP-P16DP
When the remote display is installed, service resetting is required.
1) Connect to the Display cable
1
to the display connector
2
.
2) Fix the earth wire
3
from the display unit with screw
4
.
Fig.14
B
B
A
A
A
B
UP-I16DP
Lower cabinet
ER-A771VI
How to extend display pole: UP-P16DP
– 6 –
15. How to extend display pole: UP-P16DP
The pole can be extended by installing the attached pole to the stan-
dard pole.
dard pole.
COMPONENT LIST:
1) Remove the five screws
1
.
2) Remove the Base angle
2
.
Fig.15
3) Remove the two screws
6
.
4) Remove the Base cabinet
4
from the pole cabinet
7
.
Fig.16
5) Turn the ratchet
9
connected to the pole cabinet
7
to the remov-
ing position and pull it out from the display unit
8
as shown in Fig.
A.
6) Remove the two screws
F
.
7) Remove the pole cabinet
7
from the Ratchet
9
.
Fig.17
8) Install the attached pole cabinet
G
to the pole cabinet
7
to fix it
with the screw
H
.
Fig.18
9) Install the pole cabinet
G
in the opposite order of the disassembly.
No.
NAME
USE
Q’ty
G
Pole cabinet
Pole extension
2
H
Screw (M2 x 8)
Pole connection
4
I
Screw (M4 x 16)
S e c u r i n g t h e U P - P 1 6 D P t o t h e
wooden table
wooden table
4
J
Screw (M4 x 20)
Securing the UP-P16DP to the metal
table
table
4
K
Nut
Securing the UP-P16DP to the metal
table
table
4
1
1
2
7
4
6
8
10
7
10
9
9
Fig. A
Display cable
7
7
11
11
12
12
ER-A771VI
TCP/IP I/F: Standard
– 7 –
10) Fastening on the table:
Secure the Base cabinet
2
using the screw.
Fig.19
Lowering the height of the UP-P16DP
Remove the standard Pole and attach the Base cabinet
4
to the Ratch
9
.
Fig.20
16. TCP/IP I/F: Standard
1) Connect to the Ethernet cable
1
to the Ethernet connector
2
.
2) Install the Ferrite core
3
to the Ethernet cable
1
.
3) Install the Nylon band
4
to the Ethernet cable
1
.
Fig.21
17. RS232 I/F: Standard
1) Connect the RS232 cable
1
to the connector.
2) Install the ferrite Core
2
to RS232 cable.
3) Install the ferrite core
3
to the cables.
Fig.22
No.
NAME
USE
Q’ty
I
Screw (M4 x 16)
S e c u r i n g t h e U P - P 1 6 D P t o t h e
wooden table
wooden table
4
J
Screw (M4 x 20)
Securing the UP-P16DP to the metal
table
table
4
K
Nut
Securing the UP-P16DP to the metal
table
table
4
13
13
14
14
15
15
Click on the first or last page to see other ER-A771 (serv.man6) service manuals if exist.