DOWNLOAD Sharp XE-A107 (serv.man3) Service Manual ↓ Size: 6.8 MB | Pages: 36 in PDF or view online for FREE

■

Insert the mode key (the same key as drawer lock key) into the mode switch and move the key to 
get an appropriate mode.

Mode key

: 

Turns the display off. No operations are 

 

possible.

REG:  Permits transaction entry.

: 

Permits correction after finalizing a 

 

transaction.

X/Flash: Permits printing of sales reports and 

 

displaying the flash reports.

Z/PGM:  Permits printing and resetting of sales 

 

reports and programming.

■

Your cash register is equipped with a front LED (Light-Emitting Diode) display that affords easy 

visibility of 9 digits for the operator during transaction.

Repeat

PLU code

Department code

 

Department.code: Indicates the department entered.  

For example, if department 1 was 

pressed, “1” would appear.

PLU.code: Indicates the PLU code entered.

Repeat: Indicates the number of times the 

same department key or PLU key is 

pressed repeatedly.  If an entry is 

repeated more than ten times, only 

the last digit is displayed.

 

Error: 

Appears when an error is made.  If this occurs during a transaction because of 
an extra digit entry, simply press 

l

 and re-enter correctly.

 

Program: 

Appears when the cash register is being programmed in the “Z/PGM” mode.

 

Finalization:.. Appears when a transaction is finalized by pressing 

A

, 

c

 or 

C

.

 

Subtotal: 

Appears when the cash register computes a subtotal when 

u

 is pressed, and 

also when an amount tendered is less than the total sales amount.

 

Change: 

Appears whenever a change due amount is displayed.

 

Exchange: 

Appears when 

V

 is pressed to calculate a subtotal in foreign currency.

 

Low.battery:  Appears when the voltage of the installed batteries is under the required level.  

You need to replace the batteries with new ones very soon.

 

No.battery: 

Appears when the batteries are not installed, or the installed batteries are dead. 

You must immediately replace the batteries with new ones.

To.display.the.time.and.date
Set the mode switch to the REG position, and press 

Q

 once to display the time or press 

Q

 

twice to display the date.
Press 

l

 key to cancel the time/date display.

When your register goes into an error state, it displays the error message “ ”.  Clear the error state 
by pressing 

l

 and take the appropriate action.

 

(79999999).to.RA(Received-on.Account),.PO(Paid-Out),.credit.or.cheque:
Press 

l

 and make a correct entry.

   

When.you.make.an.error.in.key.operation:
Press 

l

 and make a correct entry.

 

Check if the entered amount is correct.  If correct, check the setting of the entry digit limit.

 

When.a.subtotal.exceeds.eight.digits.(79999999):
Press 

l

 and then press 

A

, 

c

 or 

C

 to finalize the transaction at that point.

 

When.the.number.of.an.item.exceeds.3.digits.in.multiplication.entry:
Press 

l

 and re-enter a correct number.

Error.Escape.Function
When an error or something uncontrollable occurs during transaction entry and you cannot keep the 
customer waiting, press 

G

 twice (following 

l

 when in the error state).  You can escape the 

situation and finalize the transaction as a cash sale at that time.  Transaction entries until then are 
registered.

Please do the following before using the register for the first time.

For installing the cash register, find a stable surface near an AC outlet where the cash register will 
not subject to water sources or direct sunlight, then install the register.

For your register to operate properly, you must initialize it before programming for the first time. 
Follow this procedure.

  Insert the mode key into the mode switch and turn the key to the REG 

position.

  Plug the AC adapter connector into the AC adapter jack, then plug the AC 

adapter plug into the wall outlet.
IMPORTANT:. This operation must be performed without batteries loaded.

Never install the batteries into the register before initializing it.  Before you start operating the 
register, you must first initialize it, then install three new alkaline batteries LR6 (“AA” size) on 
the register.  Otherwise, distorted memory contents and malfunction of the register will occur.

  The register display should now show “      0.00”. 

  Press 

Q

  to confirm the clock starts from “      0-00”. 

  Press 

l

 to cancel the time display. 

Batteries must be installed in the cash register to prevent data and programmed contents from 
being lost from the memory in case of accidental disconnection of the AC adapter or power failure. 
Please install three new alkaline batteries LR6 (“AA” size) before programming and operating the 
cash register.

  Remove the printer cover.

  Open the battery cover next to the paper roll cradle. 

  Install three new LR6 (“AA” size) batteries. 

  Confirm the no battery symbol “ ” lights off. 

  Close the battery cover.

  Replace the printer cover.

Be careful with the paper cutter, so as not to cut yourself.

For the printer, you must install the paper roll provided with the register, even when you program the 
register for not printing receipt.

  Remove the printer cover.

 

 Open the paper guide.

 Set a paper roll in the paper roll cradle.

  Insert the paper straight into the paper inlet, and press 

F

.  

The paper then feeds through and appears in the print area.

  Close the paper guide.