Sharp ER-A570 (serv.man8) Service Manual ▷ View online
PROGRAMMING MANUAL
CODE: 00ZERA570VPME
ELECTRONIC
CASH REGISTER
CASH REGISTER
MODEL
ER-A570
(For "V" version)
SRV KEY : LKGIM7113RCZZ
PRINTER : M-820
SRV KEY : LKGIM7113RCZZ
PRINTER : M-820
CHAPTER 1. SERVICE (SRV) MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CHAPTER 2. PROGRAM (PGM2/PGM1) MODE . . . . . . . . . . . . . . . . . . . . . . . 19
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CHAPTER 4. FILE DATA TRANSMISSION (ER-02FD: 02FD MODE). . . . . . . 52
CONTENTS
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
for after sales service only.
The contents are subject to change without notice.
CHAPTER 1. SERVICE (SRV) MODE
The SRV key is used for operating in the SRV mode.
1. SRV. reset (Program Loop Reset)
Used to return the machine back to its operational state after a lock-
up has occurred.
up has occurred.
Procedure
•
Method 1
1) Turn off the AC switch.
2) Set the mode switch to (SRV
′
) position.
3) Turn on the AC switch.
4) Turn to (SRV) position from (SRV
′
) position.
•
Method 2
1) Set the mode switch to PGM2 position.
2) Turn off the AC switch.
3) While holding down JOURNAL FEED key and RECEIPT FEED
key, turn on the AC switch.
Note: When disassembling and reassembling always power up us-
ing method 1 only. Method 2 will not reset the CKDC4.
Note: SRV programming job#926-B must be set to "4" to allow PGM
program loop reset.
PRG. RESET
∗ ∗ ∗
2. Master reset (All memory clear)
There are two possible methods to perform a master reset.
•
MRS-1
Used to clear all memory contents and return machine back to its
initial settings. return keyboard back to default. for default keyboard
layout.
initial settings. return keyboard back to default. for default keyboard
layout.
Procedure
1) Turn off the AC switch.
2) Set the MODE switch to the (SRV
′
) position.
3) Turn on the AC switch.
4) While holding down JOURNAL FEED key, turn to (SRV) position
from (SRV
′
) position.
•
MRS-2
Used to clear all memory and keyboard contents.
This reset returns all programming back to defaults. The keyboard
must be entered by hand.
This reset is used if an application needs different keyboard layout
other than that supplied by a normal MRS-1.
Used to clear all memory and keyboard contents.
This reset returns all programming back to defaults. The keyboard
must be entered by hand.
This reset is used if an application needs different keyboard layout
other than that supplied by a normal MRS-1.
Procedure
1) Turn off the AC switch.
2) Set the MODE switch to the (SRV
′
) position.
3) Turn on the AC switch.
4) While holding down JOURNAL FEED key and RECEIPT FEED
key, turn to (SRV) position from (SRV
′
) position.
5) Key position assignment:
∗
After the execution of MRS-2, only the RECEIPT FEED and
JOURNAL FEED keys can remain effective on key assignment.
Any key can be assigned on any key position on the main key-
board.
JOURNAL FEED keys can remain effective on key assignment.
Any key can be assigned on any key position on the main key-
board.
[key setup procedure]
MASTER PRESET
∗ ∗ ∗
NOTES:
∗
1: When the 0 key is pressed, the key of the key number on
display is disabled.
∗
2: Push the key on the position to be assigned. With this, the key
of the key number on display is assigned to that key position.
∗
3: When relocating the keyboard, the PGM 1/2 use standard key
layout.
Key number
Key name
Key number
Key name
1
Numeric key "0"
10
Numeric key "9"
2
Numeric key "1"
11
Numeric key "00"
3
Numeric key "2"
12
Numeric key "000"
4
Numeric key "3"
13
Decimal point key
5
Numeric key "4"
14
CL key
6
Numeric key "5"
15
⊗
key
7
Numeric key "6"
16
ST key
8
Numeric key "7"
17
TL key
9
Numeric key "8"
3. Reading of the SRV mode program
List of program reports
JOB#
Report name
900
SRV-mode program full item report (not incl. keyboard
layout)
layout)
950
Keyboard layout report (on keys other than dept. keys
and direct PLU keys)
and direct PLU keys)
951
Keyboard layout report (on dept. keys and direct PLU
keys)
keys)
970
SRV file programming report
MRS-2 executed
Key position set
Free key
Disable
Free key setup
complete.
complete.
*2
*1
0
0
1
[JOB# 900]
All parameters contained for the SRV mode as listed
Key operation.
900
→
⊗
→
TL
01/ 01/ 00 0: 00
DATE (DD/MM/YY)/TIME
000000#0001
MACHINE NO./CC-NO.
#900
JOB CODE
901# 0102
902# 0000
CONTENTS OF THE SRV-MODE
PROGRAMMING
PROGRAMMING
903# 4270
904# 0000
905# 0100
906# 0001
The contents of the programming are
printed only on the journal individual for-
mats shown at left. (No header is
printed.)
printed only on the journal individual for-
mats shown at left. (No header is
printed.)
907# 0014
908# 0000
909# 0001
910# 0003
911# 0400
912# 1141
913# 0002
914# 0100
915# 1020
916# 1000
917# 0000
918# 0000
919# 4000
920# 0000
921# 0000
922# 0008
923# 0000
924# 0000
925# 0000
926# 0004
927# 0000
928# 0104
929# 0000
930# ζ1 0000
GENERAL Z1 RESET COUNTER
931# χον ζ1 0000
ΧΟΝΣΟΛΙ∆ΑΤΕ∆ Ζ1 ΡΕΣΕΤ ΧΟΥΝΤΕΡ
932# ζ1 0000
CLERK Z1 RESET COUNTER
933# ζ1 0000
HOURLY Z1 RESET COUNTER
934# ζ1 0000
PLU Z1 RESET COUNTER
935# ζ1 0000
CASHIER Z1 RESET COUNTER
936# ζ1 0000
GLU/PBLU Z1 RESET COUNTER
937# ζ2 0000
GENERAL Z2 RESET COUNTER
938# χον ζ2 0000
ΧΟΝΣΟΛΙ∆ΑΤΕ∆ Ζ2 ΡΕΣΕΤ ΧΟΥΝΤΕΡ
939# ζ2 0000
DAILY NET Z2 RESET COUNTER
942#
Γ Τ 2 ∗00000000000. 00
943#
Γ Τ 3 ∗00000000000. 00
944# 0000
PGM2 MODE SECRET CODE
945# 0000
ASSIGNMENT OF RS232C CHANNEL
946# 0000
ASSIGNMENT OF RS232C CHANNEL
948# 000 000
TRAINING CLERK NO.
949# τραι νι νγ
TRAINING MODE’S TITLE
[JOB# 950]
The Key layout report is printed in SRV mode
Key operation
950
→
⊗
→
TL
Key operation
951
→
⊗
→
TL
21 / 09 / 94 14 : 30
123456#0123
#950
001
KEY
DATE (DD/MM/YY)/TIME
MACHINE NO./CC-NO.
JOB CODE
KEY NO./KEY LABEL
/LOCATION NO.
:
:
0
019
002
KEY
1
020
003
KEY
2
030
21 / 09 / 94 14 : 30
123456#0123
#951
001
DATE (DD/MM/YY)/TIME
MACHINE NO./CC-NO.
JOB CODE
KEY NO./KEY TEXT
/LOCATION NO.
:
:
0
079
0 1
002
0
080
0 2
003
0
081
0 3
158
1
-
5 8
- -
159
1
-
5 9
- -
160
1
-
6 0
- -
2
Σ
[JOB#970]
Files on the memory are listed.
Key operation
970
→
⊗
→
TL
01/ 01/ 00 0: 04
DATE (DD/MM/YY)/TIME
000000#0006
MACHINE NO./CC-NO.
#970
JOB CODE
∗001∗ 00020 / 00020
∗002∗ 00020 / 00020
∗003∗ 00020 / 00020
∗005∗ 00020 / 00020
∗006∗ 00020 / 00020
∗015∗ 00240 / 00020
∗016∗ 00240 / 00020
∗020∗ 00240 / 00020
∗023∗ 00240 / 00020
∗024∗ 00240 / 00020
∗033∗ 00030 / 00000
∗034∗ 00010 / 00000
∗060∗ 00099 / 00099
∗061∗ 00099 / 00099
∗062∗ 00099 / 00099
∗086∗ 00006 / 00006
∗087∗ 00006 / 00006
∗088∗ 00006 / 00006
∗092∗ 00076 006/ 00076
FILE TABLE NO./NO. OF RECORDS/NO. OF BLOCKS/NO. OF USED RECORDS
∗093∗ 00076 006/ 00076
∗094∗ 00076 006/ 00076
∗098∗ 00076 / 00076
∗099∗ 00076 / 00076
∗103∗ 00076 / 00076
∗104∗ 00076 / 00076
∗108∗ 00049 / 00049
∗109∗ 00049 / 00049
∗113∗ 00032 / 00000
∗114∗ 00032 / 00000
∗119∗ 00080 / 00080
∗122∗ 00080 / 00080
∗123∗ 00080 / 00080
∗126∗ 00050−01350
FILE TABLE NO./NO. OF INDEX RECORDS-NO. OF DATA RECORDS
/ 00000
/NO. OF USED RECORDS (GLU)
∗130∗ 00075 / 00075
∗131∗ 00021 / 00021
∗132∗ 00304 / 00304
1χ6600
FILE MEMORY START ADDRESS
1δφε06
EMPTY MEMORY START ADDRESS
1φφφφφ
MEMORY END ADDRESS
[JOB#990]
Reading the Contents of the SRV-Mode Programming for SSP
Key operation
990
→
⊗
→
TL
11/01/9412:34pm
123456#0123
123456#0123
#990
ssp era570 -001
1 001
02 001
003 001
check sum error
DATE (DD/MM/YY)/TIME
MACHINE NO./CC-NO.
JOB CODE
SSP NO.
3