Sharp ER-A440 (serv.man5) Service Manual ▷ View online
ELECTRONIC
CASH REGISTER
CASH REGISTER
ER-A440
MODEL
ER-A450
(For "V" version)
SRV KEY: LKGIM7113RCZZ
PRINTER: DP-730 (Dot printer) for ER-A440
SRV KEY: LKGIM7113RCZZ
PRINTER: DP-730 (Dot printer) for ER-A440
PR-45M (Thermal printer) for ER-A450
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
for after sales service only.
The contents are subject to change without notice.
CHAPTER 1. SERVICE (SRV) MODE . . . . . . . . . . . . . . . . . . . . . . . . 1-1
CHAPTER 2. PROGRAM (PGM2/PGM1) MODE . . . . . . . . . . . . . . . . 2-1
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE . . . . . . . . . . . . . . . . . . . . 3-1
CHAPTER 4. CHANGING EURO FUNCTION (X2/Z2 mode JOB). . . 4-1
CONTENTS
CHAPTER 1. SERVICE (SRV) MODE
The SRV key is used for operating in the SRV mode.
1. SRV. reset (Program Loop Reset)
Used to return the machine back to its operational state after a lock-
up has occurred.
up has occurred.
Procedure
•
Method 1
1) Turn off the AC switch.
2) Set the mode switch to (SRV
′
) position.
3) Turn on the AC switch.
4) Turn to (SRV) position from (SRV
′
) position.
•
Method 2
1) Set the mode switch to PGM2 position.
2) Turn off the AC switch.
3) While holding down JOURNAL FEED key and RECEIPT FEED
key, turn on the AC switch.
Note: When disassembling and reassembling always power up us-
ing method 1 only. Method 2 will not reset the CKDC8.
Note: SRV programming job#926-B must be set to "4" to allow PGM
program loop reset.
PRG. RESET
2. Master reset (All memory clear)
There are two possible methods to perform a master reset.
•
MRS-1
Used to clear all memory contents and return machine back to its
initial settings. return keyboard back to default. for default keyboard
layout.
initial settings. return keyboard back to default. for default keyboard
layout.
Procedure
1) Turn off the AC switch.
2) Set the MODE switch to the (SRV
′
) position.
3) Turn on the AC switch.
4) While holding down JOURNAL FEED key, turn to (SRV) position
from (SRV
′
) position.
•
MRS-2
Used to clear all memory and keyboard contents.
This reset returns all programming back to defaults. The keyboard
must be entered by hand.
This reset is used if an application needs different keyboard layout
other than that supplied by a normal MRS-1.
Used to clear all memory and keyboard contents.
This reset returns all programming back to defaults. The keyboard
must be entered by hand.
This reset is used if an application needs different keyboard layout
other than that supplied by a normal MRS-1.
Procedure
1) Turn off the AC switch.
2) Set the MODE switch to the (SRV
′
) position.
3) Turn on the AC switch.
4) While holding down JOURNAL FEED key and RECEIPT FEED
key, turn to (SRV) position from (SRV
′
) position.
5) Key position assignment:
After the execution of MRS-2, only the RECEIPT FEED and
JOURNAL FEED keys can remain effective on key assignment.
Any key can be assigned on any key position on the main key-
board.
JOURNAL FEED keys can remain effective on key assignment.
Any key can be assigned on any key position on the main key-
board.
[key setup procedure]
MASTER RESET
NOTES:
1: When the 0 key is pressed, the key of the key number on
display is disabled.
2: Push the key on the position to be assigned. With this, the key
of the key number on display is assigned to that key position.
Key number
Key name
Key number
Key name
1
Numeric key "0"
9
Numeric key "8"
2
Numeric key "1"
10
Numeric key "9"
3
Numeric key "2"
11
Numeric key "00"
4
Numeric key "3"
13
Decimal point key
5
Numeric key "4"
14
CL key
6
Numeric key "5"
15
⊗
key
7
Numeric key "6"
16
ST key
8
Numeric key "7"
17
TL key
3. Reading of the SRV mode program
List of program reports
JOB#
Report name
900
SRV-mode program full item report (not incl. keyboard
layout)
layout)
950
Keyboard layout report (on keys other than dept. keys
and direct PLU keys)
and direct PLU keys)
951
Keyboard layout report (on dept. keys and direct PLU
keys)
keys)
970
SRV file programming report
MRS-2 executed
Key position set
Free key
Disable
Free key setup
complete.
complete.
*2
*1
0
0
1 – 1
This printing sample is used from the ER-A450.
The printed data from the ER-A440 is the same as the ER-A450.
[JOB# 900]
Reading the contents of the SRV mode programming
Key operation.
[JOB# 950]
Reading the contents of the SRV mode programming for FREE KEY
LAYOUT setting. (Function Key)
LAYOUT setting. (Function Key)
Key operation
900
TL
Header graphical logo(Default:
Graphical LOGO only)
Graphical LOGO only)
Date/Time
Machine No./Consective No.
JOB#
JOB#//Programming
data(ABCD)
data(ABCD)
General Z1 reset counter
Clerk Z1 reset counter
Hourly Z1 counter
PLU Z1/Z2 reset counter
Cashier Z1 reset counter
General Z2 reset counter
Daily net Z2 reset counter
Clerk Z1 reset counter
Hourly Z1 counter
PLU Z1/Z2 reset counter
Cashier Z1 reset counter
General Z2 reset counter
Daily net Z2 reset counter
GT2 counter
GT3 counter
Secret code for PGM2 mode
Training cashier No.
Training mode title
Domestic currency symbol
Training mode title
Domestic currency symbol
Initial text mode programming
For ER-A440:
(Default: 3 line header)
(Default: 3 line header)
950
TL
Header graphical logo
Date/Time
Machine No./Consective No.
JOB#
Key No./Key label name/
Location No.
Location No.
Key No./Key label name/
Location No.(---:Not used)
Location No.(---:Not used)
1 – 2
[JOB# 951]
Reading the contents of the SRV mode programming for FREE KEY
LAYOUT setting. (Dept. & PLU key)
LAYOUT setting. (Dept. & PLU key)
Key operation
951
TL
Header graphical logo
Date/Time
Machine No./Consective No.
JOB#
Key No./Key label name/
Location No.
Location No.
Key No./Key label name/
Location No.(---:Not used)
Location No.(---:Not used)
1 – 3
