DOWNLOAD Sharp DV-S1 (serv.man5) Service Manual ↓ Size: 191.8 KB | Pages: 3 in PDF or view online for FREE

1-6-1

E56H0DC

This flowchart indicates the disassembly steps to gain
access to item(s) to be serviced. When reassembling,
follow the steps in reverse order. Bend, route, and dress
the cables as they were originally.

1 : Identification (location) No. of parts in the figures

2 : Name of the part

3 : Figure Number for reference

4 : Identification of parts to be removed, unhooked,

unlocked, released, unplugged, unclamped, or de-
soldered.
P=Spring, L=Locking Tab, S=Screw,
CN=Connector,
*=Unhook, Unlock, Release, Unplug, or Desolder
e.g. 5(S-1) = five Screws (S-1),

2(L-2) = two Locking Tabs (L-2)

5 : Refer to "Reference Notes."

CAUTION 1: Locking Tabs (L-1), (L-2) and (L-3) are
fragile. Be careful not to break them.

1-1. Connect the wall plug to an AC outlet and press the

OPEN/CLOSE button to open the Tray.

1-2. Remove the Tray Panel by releasing two Locking

Tabs (L-1).

1-3. Press the OPEN/CLOSE button again to close the

Tray.

1-4. Press the POWER button to turn the power off.

1-5. Unplug an AC Cord.

1-6. Release two Locking Tabs (L-2). Then, release

five Locking Tabs (L-3) (to do this, first release two
Locking Tabs (A) at the bottom, and then three
Locking Tabs (B) at the side.) (Fig. 2)

CAUTION 2: Electrostatic breakdown of the laser diode
in the optical system block may occur as a potential
difference caused by electrostatic charge accumulated
on cloth, human body etc., during unpacking or repair
work.

To avoid damage of pickup follow next procedures.

2-1. Slide out the pickup unit as shown in Fig. 4.

2-2. Short the three short lands of FPC cable with

solder before removing the FFC cable (CN101)
from it. If you disconnect the FFC cable (CN101),
the laser diode of pickup will be destroyed. (Fig. 4)

2-3. Disconnect Connector (CN401). Remove three

Screws (S-2) and lift the DVD Mecha. (Fig. 3)

CAUTION 3: When reassembling, confirm the FFC
cable (CN101) is connected completely. Then remove
the solder from the three short lands of FPC cable.
(Fig. 4)

[1] Top Cover

1

5(S-1)

-

[2] Front

2

*2(L-1), Tray Panel,

1-1

Assembly

*2(L-2), *5(L-3)

1-2
1-3
1-4
1-5
1-6

[3] DVD

3,4

3(S-2)

2

Mecha

*CN101, *CN401

2-1
2-2
2-3

3

[4] AV CBA

5

4(S-3), 6(S-4),

-

*2(L-4), *CN1001,
*CN1601

[5] DVD Main

5

3(S-5)

-

CBA Unit

[6] Rear

6

3(S-6)

-

Panel

↑

↑

↑

↑

↑

1

2

3

4

5

[1] Top Cover

[2] Front Assembly

[3] DVD Mecha

[5] DVD Main CBA Unit

[4] AV CBA

[6] Rear Panel

1-6-2

E56H0DC

(S-1)

(S-1)

[1] Top Cover

(S-1)

Fig. 1

[2] Front Assembly

Tray Panel

(A)

(A)

(L-3)

(L-2)

(L-1)

(L-1)

(B)

Fig. 2

[3] DVD Mecha

(S-2)

(S-2)

CN101

CN401

Fig. 3

View for B

Pickup Unit 

C

B

Short the three short 
lands by soldering

View for C

Slide

View for A

OR

Short the three short lands by soldering

DVD Mecha

A

Fig. 4

1-6-3

E56H0DC

[4] AV CBA

[5] DVD Main CBA Unit

(S-5)

(S-5)

(S-3)

(S-4)

(S-3)

CN1601

CN1001

(S-4)

(L-4)

(S-4)

Fig. 5

[6] Rear Panel

(S-6)

Fig. 6

Eject-Bar (Length = approximately 80 mm, Diameter = approximately 3 mm)

Manual 
Eject Hole

DVD Mecha

Tray

Top Case

1

3

2

1. Remove the Top Case.

2. Insert the eject-bar (length = approximately 80 mm,

diameter = approximately 3 mm) into the manual eject
hole on the DVD Mecha. Then, press it until the tray
is ejected.