DOWNLOAD Sharp DV-S1 (serv.man3) Service Manual ↓ Size: 99.72 KB | Pages: 5 in PDF or view online for FREE

1-2-1

DVD_LASER

This DVD player uses a pickup that emits a laser beam.

The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your
eyes at least 30cm away from the pickup lens when the diode is turned on. Do not look directly at the laser beam.

Caution: Use of controls and adjustments, or doing procedures other than those specified herein, may result in
hazardous radiation exposure.

Drive Mecha Assembly

Turntable

Laser Beam Radiation

Laser Pickup

CAUTION -  VISIBLE LASER 
RADIATION WHEN OPEN AND 
INTERLOCK DEFEATED.
AVOID EXPOSURE TO BEAM.

1-3-1

E56A0IMP

BEFORE RETURNING THE DVD VIDEO PLAYER

Before returning the DVD video player to the user,
perform the following safety checks.

1. Inspect all lead dress to make certain that leads are

not pinched or that hardware is not lodged between
the chassis and other metal parts in the DVD video
player.

2. Inspect all protective devices such as non-metallic

control knobs, insulation materials, cabinet backs,
adjustment and compartment covers or shields, isola-
tion resistor/capacitor networks, mechanical insula-
tors etc.

3. To be sure that no shock hazard exists, check for

current in the following manner.
Plug the AC line cord directly into a 230 volt AC outlet
(Do not use an isolation transformer for this test).
Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15

µF capacitor in series with

all exposed metal cabinet parts and a known earth
ground, such as a water pipe or conduit.
Use an DVM or VOM with 1000 ohm per volt, or higher,
sensitivity or measure the AC voltage drop across the
resistor (See Diagram).
Move the resistor connection to earth exposed metal
part having a return path to the chassis (metal cabinet,
screw heads, knobs and control shafts, etc.) and
measure the AC voltage drop across the resistor.

Reverse the AC plug on the set and repeat AC voltage
measurements for each exposed part. Any reading of
1.4V rms (this corresponds to 0.7mA rms AC.) or more
is excessive and indicates a potential shock hazard
which must be corrected before returning the DVD
video player to the owner.

AVANT DE RENDRE LE REPRODUCTOR DE VíDEO
DVD

Avant de rendre le reproductor de vídeo DVD à l’utilisateur,
effectuer les vérifications de sécurité suivantes.

1. Vérifier toutes les gaines de fil pour être sûr que les fils

ne sont pas pincés ou que le matériel n’est pas coincé
entre le châssis et les autres pièces métalliques dans le
reproductor de vídeo DVD.

2. Vérifier tous les dispositifs de protection tels que les

boutons de commande non métalliques, les matériaux
d’isolement, le dos du coffret, les couvercles de
compartiment et ajustement ou les boucliers, les
réseaux de résistance / condensateur d’isolement, Ies
isolateurs mécaniques, etc.

3. Pour être sûr qu’il n’y a aucun risque de choc électrique,

vérifier le courant de fuite de la maniére suivante.
Brancher le cordon d’alimentation secteur directement
dans une prise de courant de 230 volts. (Ne pas utiliser
de transformateur d’isolement pour cet essai).
Utiliser deux fils à pinces et connecter une résistance
de 10 watts 1,5 kohm en parallèle avec un condensateur
de 0,15 

µF en série avec des pièces du coffret métallique

exposées et une masse de terre connue telle qu’un
tuyau ou un conduit d’eau.
Utiliser un DVM ou VOM avec une sensibilité de 1000
ohms par volt ou plus ou mesurer la chute de tension
CA entre la résistance (voir diagramme).
Déposer la connexion de la résistance à toutes les

pièces métalliques exposées ayant un parcours de
retour au châssis (coffret métallique, tétes de vis, bou-
tons et arbres de commande, etc.) et mesurer la chute
de tension CA entre la résistance. Inverser la fiche CA
(une fiche intermédiaire non polarisée doit être utilisée
à seule fin de faire ces vérifications.) sur l’appareil et
répéter les mesures de tension CA pour chaque piéce
métallique exposée. Toute lecture de 1,4 V rms (ceci
correspond à 0,7 mA rms CA) ou plus est excessive et
signale un danger de choc qui doit être corrigé avant de
rendre le reproductor de vídeo DVD à son utilisateur.

SSVM

AC SCALE

2k ohms.

10W

0.15

TEST PROBE

TO EXPOSED
METAL PARTS

CONNECT TO
KNOWN EARTH 
GROUNG

F

SSVM

AC SCALE

2k ohms.

10W

0.15

TEST PROBE

TO EXPOSED
METAL PARTS

CONNECT TO
KNOWN EARTH 
GROUNG

F

1-4-1

DVD_NOTE

a. The output pin of the 3 pin Regulator ICs is indicated

as shown.

Top View

Out

In

Bottom View

Input

b. For other ICs, pin 1 and every fifth pin are indicated

as shown.

5

10

Pin 1

c. The 1st pin of every male connector is indicated as

shown.

Pin 1

1. When you connect or disconnect the FFC (Flexible

Foil Connector) cable, be sure to first disconnect the
AC cord.

2. FFC (Flexible Foil Connector) cable should be in-

serted parallel into the connector, not at an angle.

FFC Cable

Connector

CBA

* Be careful to avoid a short circuit.

(1) Prepare the hot-air flat pack-IC desoldering ma-

chine, then apply hot air to the Flat Pack-IC (about 5
to 6 seconds). (Fig. S-1-1)

(2) Remove the flat pack-IC with tweezers while apply-

ing the hot air.

(3) Bottom of the flat pack-IC is fixed with glue to the

CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

(4) Release the flat pack-IC from the CBA using twee-

zers. (Fig. S-1-6)

1. Do not supply hot air to the chip parts around the flat

pack-IC for over 6 seconds because damage  to the
chip parts may occur. Put masking tape around the
flat pack-IC to protect other parts from damage.
(Fig. S-1-2)

2. The flat pack-IC on the CBA is affixed with glue, so

be careful not to break or damage the foil of each pin
or the solder lands under the IC when removing it.

Hot-air
Flat Pack-IC
Desoldering
Machine

CBA

Flat Pack-IC

Tweezers

Masking 
Tape

1-4-2

DVD_NOTE

(1) Using desoldering braid, remove the solder from all

pins of the flat pack-IC. When you use solder flux
which is applied to all pins of the flat pack-IC, you can
remove it easily. (Fig. S-1-3)

Flat Pack-IC

Desoldering Braid

Soldering Iron

(2) Lift each lead of the flat pack-IC upward one by one,

using a sharp pin or wire to which solder will not
adhere (iron wire). When heating the pins, use a fine
tip soldering iron or a hot air desoldering machine.
(Fig. S-1-4)

Fine Tip
Soldering Iron

Sharp
Pin

(3) Bottom of the flat pack-IC is fixed with glue to the

CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

(4) Release the flat pack-IC from the CBA using twee-

zers. (Fig. S-1-6)

(1) Using desoldering braid, remove the solder from all

pins of the flat pack-IC. When you use solder flux
which is applied to all pins of the flat pack-IC, you can
remove it easily. (Fig. S-1-3)

(2) Affix the wire to a workbench or solid mounting point,

as shown in Fig. S-1-5.

(3) While heating the pins using a fine tip soldering iron

or hot air blower, pull up the wire as the solder melts
so as to lift the IC leads from the CBA contact pads
as shown in Fig. S-1-5.

(4) Bottom of the flat pack-IC is fixed with glue to the

CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

(5) Release the flat pack-IC from the CBA using twee-

zers. (Fig. S-1-6)

When using a soldering iron, care must be taken to
ensure that the flat pack-IC is not being held by glue.
When the flat pack-IC is removed from the CBA,
handle it gently because it may be damaged if force
is applied.

To Solid 
Mounting Point

Soldering Iron

Iron Wire

or

Hot Air Blower

Fine Tip
Soldeing Iron

CBA

Flat Pack-IC

Tweezers