Sharp DV-NC65H (serv.man6) Service Manual ▷ View online
40
DV-NC65H/S
DV-NC70H
DV-NC70H
8-25. INSTALLING THE MASTER CAM (AT REAR
SIDE OF MECHANISM CHASSIS)
1. Before installing the master cam, make sure that the
sifter is at initial position. (Right side from bottom view)
2. Place the master cam by pushing in so that the long hole
of the master cam comes to the front side as shown
below.
below.
3. Fix the E-ring.
4. Adjust the master cam and pinch drive cam, fix the
4. Adjust the master cam and pinch drive cam, fix the
synchro gear in correct position.
Note:
See the figure below for the phase matching between the
master cam synchro gear and pinch drive cam.
• Phase alignment of the master cam and the synchro
See the figure below for the phase matching between the
master cam synchro gear and pinch drive cam.
• Phase alignment of the master cam and the synchro
gear;
Align the wide tooth space and the composite tooth.
Align the wide tooth space and the composite tooth.
• Phase alignment of the synchro gear and the pinch drive
cam;
Adjust the teeth so as to orient the rib of the synchro gear
and the hole of the pinch drive cam.
Adjust the teeth so as to orient the rib of the synchro gear
and the hole of the pinch drive cam.
Figure 8-39-2.
Figure 8-39-1.
E-ring
Pinch Drive Cam
Synchro
gear
gear
Phase
matching
matching
Hole of Pinch Drive Cam
Master Cam
Phase
matching
matching
Rib
Push in with this long hole
toward you. The sifter
moves slightly to the left.
toward you. The sifter
moves slightly to the left.
8-26. REPLACEMENT OF LOADING MOTOR
• Removal
• Replacement
Remove the loading motor, and install the replacement
loading motor as shown below.
Remove the loading motor, and install the replacement
loading motor as shown below.
Figure 8-41.
The loading motor pressing-in must be less than 196N (20
kgf).
Adjust the distance between motor and pulley to 6.95
mm.
kgf).
Adjust the distance between motor and pulley to 6.95
mm.
Figure 8-40.
+0
. 2
–0.15
6.95 mm
A part
Worm gear
+0
- 0.15
Loading
motor
motor
To press the motor in, first
receive it by portion A.
receive it by portion A.
Apply grease
Worm gear
Apply grease
Apply grease
Apply grease
L-M-Block.
Worm wheel gear.
Leading connect gear.
*Apply grease to
the tip as well.
Loading
motor.
Wire
+ : Red
- : White
+ : Red
- : White
Red
Insert
(
41
DV-NC65H/S
DV-NC70H
DV-NC70H
8-27. ASSEMBLY OF CASSETTE HOUSING
1. Proof lever, Proof lever spring and Holder R
Figure 8-42.
MSPRD0215AJFJ
*Proof lever spring fixing direction designated.
MSPRD0212AJFJ
Take care
not to damage
this part
not to damage
this part
Outside
Outer
Top
Bottom
Inner
2. Open lever, Sensor Plate and Drive Lever to Frame R
3. Spring to Drive Arm R
Figure 8-43.
Figure 8-44.
42
DV-NC65H/S
DV-NC70H
DV-NC70H
Figure 8-45.
LANGF9661AJFW
Top surface should be free from scratches or soil.
When assemble drive lever to frame R (on the
back side), make sure the hole synchronize.
back side), make sure the hole synchronize.
4. Frame R, Frame L, Drive Arm R, Drive Arm L, Upper Plate.
43
DV-NC65H/S
DV-NC70H
DV-NC70H
10000000
~~~~~~~~
The preparation date
display of the program
10000001 00005502
Model number display
10000002
~~~~~~~~
The version display of
the program
10000003 00000002
Region number
display
10000004
~~~~~~~~ ~
Micro-code version
display
10000005
~~~~~~~~ ~~~~~~~~ Servo program version
display
10000006
~~~~~~~~
Source code version
display
Return to the initial testmode image.
<Press "1" Key on the remote control or "Stop" Key on the main unit.>
Return to the initial testmode image.
"Playback" Key of the remote control
is pushed for 7 times.
is pushed for 7 times.
To (1)
All FIP light up
40000000 00000000 (OSD only)
<Press "4" Key of the remote control>
Press "4" Key of the remote control.
"NO DISC" state
"F0" Key input (Press "Play" Key and "Stop" Key for 5 seconds.)
F0000000 00000000
LASER TEST
DVD LD ON
LASER TEST
CD LD ON
"1" Key input
"3" Key input
"1" Key input
"1" Key input
"1" Key input
The tray opens, the DVD laser is lit, spinning is performed
and the sled moves to the outer periphery.
The DVD laser goes out, the CD laser is lit, spinning is performed
and the sled moves to the outer periphery.
LASER TEST
LD OFF
The DVD and CD laser go out, spinning is performed
and the sled moves to the outer periphery.
Laser test mode
10000006 00000000
DYNAMIC TEST
9. TEST MODE
Click on the first or last page to see other DV-NC65H (serv.man6) service manuals if exist.