Sharp DV-NC60H (serv.man12) Service Manual ▷ View online
56
DV-NC55S/H
DV-NC60H
DV-NC60H
FLOW CHART NO.1
NO
YES
NO
YES
NO
YES
NO
YES
NO
Are STBY 44V, AT 23V, PC 12V, STBY –24V,
STBY 5V and filament voltage lines normal?
Is the fuse good?
Is the normal state restored when once unplugged
power cord is plugged again after several seconds?
Is "H" level applied at pin(1) of IC701?
The fuse blows out even when it is
replaced with new one.
See FLOW CHART NO.2 <Fuse blown out.>.
Check for leak or short-circuiting of primary circuit
part.(L901, D910-3, T901, Q901-902, etc.)
Check each rectifier circuits and short-circuit of
secondary circuit.
Check the power failure circuit.
(Q704 and the peripheral circuit)
Are AT 5V voltage line normal?
No power
FLOW CHART NO.2
Check for leak or short-circuiting of primary
circuit part. (L901, T901, Q901-902, etc.)
Check for short-circuiting of rectifying diode and
circuit in each rectifying circuit of secondary circuit.
(D9601-6)
Case (2)
Case (1)
Fuse blown out.
FLOW CHART NO.3
Is the photocoupler circuit on the secondary side
operating normally?
NO
YES
NO
YES
Is the control of photocoupler circuit on the primary
side operating normally?
Replace IC701, IC702.
Check the circuit and replace parts.
(IC901, IC902, IC9601, etc.)
Check the circuit and replace parts.
(IC901, IC902, IC9601, Q902, etc.)
FLOW CHART NO.4
Check for short-circuiting of circuit and rectifying diode of each rectifying circuit of secondary
circuit and check for failure of shunt regulator circuit. (D9601-6, IC9601, C9613, C9618)
When the output voltage varies.
When buzz is heard from the vicinity of power circuit.
NO
NO
NO
NO
NO
NO
NO
NO
FLOW CHART NO.5
Does the change from STANDBY LED indicate
turn-off?
Check the AT 5V line.
YES
Is the supply voltage of 5V fed to pin(9) of IC8201?
Check the IC8202.
Is the supply voltage about 5V fed to pin(11) of
IC8201?
Check the FL8201 and IC8201.
Is there 4.0MHz oscillation at pins(6) and (8) of
IC8201?
Check the S5001 and POWER KEY line.
Does the "L" signal inputted at pin(13) of IC8201,
when the POWER button activated on the DVD?
Replace IC8201.
Replace IC8201.
The STANDBY LED indicate it flashing after 0.5sec.
Are the "H" pulse inputted into the pin(33) of
IC8201?
Check the line between the remote control
receiver and the pin(10) of IC8201.
Does the remote control "L" signal inputted at
pin(10) of IC8201, when the POWER button
activated on the remote control unit?
Replace IC8201.
Are the "P–CON(L)" pulse outputted from the
pin(32) of IC8201?
Check each component and if poor the replace.
Check or replace D9091-95.
Does the P–CON switch circuit is operate
normally? (Q9053-5, Q9058, IC9053-54)
The DVD power cannot be turned on.
YES
YES
YES
YES
YES
YES
YES
YES
YES
Yes (below, confirmed operating at LED turn-off of 0.5sec interval.)
(PO
WER)
57
DV-NC55S/H
DV-NC60H
DV-NC60H
YES
YES
NO
NO
NO
NO
YES
YES
YES
YES
YES
NO
NO
PC 9V is not output.
FLOW CHART NO.6
Check the secondary circuit, AT 12V and PC 12V
switch(Q9053)
circuit.
Is voltage of 9V sent out from the pin(2) of IC9052?
Check for load circuit short-circuiting or leak.
Check the IC9052 periphery circuit.
Are the "H" pulse inputted into the pin(9) of IC8201?
Does the P-CON switch circuit is operate ally?
(Q9056-7, Q9053, etc.)
Check each component and if poor the replace.
Replace IC8201.
Check or replace D9091-5.
FLOW CHART NO.7
Is 12V voltage supplied at pin(1) of IC9052?
Check the PC 12V line.
Is voltage of 8V sent out from the pin(2) of IC9052?
Check for load circuit short-circuiting or leak.
Check the IC9052 periphery circuit.
Replace IC9052.
Is 12V voltage supplied at pin(1) of IC9052?
PC 8V is not output.(PC 9V is possible)
FLOW CHART NO.8
Is 5V voltage supplied at emitter of Q9054?
Check the AT 5V line.
Is voltage of 5V sent out from the collector of
Q9054?
Check for load circuit short-circuiting or leak.
Check the Q9054 periphery circuit.
Does the P-CON switch circuit is operate
normally? (Q9056-7, etc.)
Check each component and if poor the replace.
Are the
"H" pulse inputted into the pin(9) of
IC8201?
Replace IC8201.
Check or replace D9091-5.
NO
NO
NO
YES
YES
YES
YES
YES
NO
PC 5V is not output.
FLOW CHART NO.9
Is -22V voltage supplied at emitter of Q8202?
Check the AT -22V line.
Is voltage of -22V sent out from the collector of
Q8202?
Check for load circuit short-circuiting or leak.
Check the Q8202 periphery circuit.
Are the
"H" pulse inputted into the pin(32) of
IC8201?
Does the P-CON switch circuit is operate normally?
(Q8201, etc.)
Check each component and if poor the replace.
Replace IC8201.
Check or replace D9091-5.
FLOW CHART NO.10
Is 5V voltage supplied at pin(1) of IC9053?
Check the secondary circuit, AT 5V line.
Is voltage of 3.3V sent out from the pin(2) of IC9053?
Check for load circuit short-circuiting or leak.
Check the IC9053 periphery circuit.
Are the
"H" pulse inputted into the pin(9) of IC8201?
Does the P-CON switch circuit is operate normally?
(Q9056-7, etc.)
Check each component and if poor the replace.
Replace IC8201.
Check or replace D9091-5.
NO
NO
NO
NO
NO
NO
YES
YES
YES
YES
YES
YES
YES
YES
NO
YES
YES
NO
PC -22V is not output.
PC 3.3V(1), (2) is not output.
FLOW CHART NO.11
Is 5V voltage supplied at pin(1) of IC9054?
Is voltage of 2.5V sent out from the pin(2) of
IC9054?
Check the secondary circuit, AT 5V line.
Check for load circuit short-circuiting or leak.
Check the IC9054 periphery circuit.
Replace IC9054.
NO
YES
YES
YES
NO
PC 1.8V is not output.(PC 3.3V(1), (2) is possib
le)
57
DV-NC55S/H
DV-NC60H
DV-NC60H
YES
YES
NO
NO
NO
NO
YES
YES
YES
YES
YES
NO
NO
PC 9V is not output.
FLOW CHART NO.6
Check the secondary circuit, AT 12V and PC 12V
switch(Q9053)
circuit.
Is voltage of 9V sent out from the pin(2) of IC9052?
Check for load circuit short-circuiting or leak.
Check the IC9052 periphery circuit.
Are the "H" pulse inputted into the pin(9) of IC8201?
Does the P-CON switch circuit is operate ally?
(Q9056-7, Q9053, etc.)
Check each component and if poor the replace.
Replace IC8201.
Check or replace D9091-5.
FLOW CHART NO.7
Is 12V voltage supplied at pin(1) of IC9052?
Check the PC 12V line.
Is voltage of 8V sent out from the pin(2) of IC9052?
Check for load circuit short-circuiting or leak.
Check the IC9052 periphery circuit.
Replace IC9052.
Is 12V voltage supplied at pin(1) of IC9052?
PC 8V is not output.(PC 9V is possible)
FLOW CHART NO.8
Is 5V voltage supplied at emitter of Q9054?
Check the AT 5V line.
Is voltage of 5V sent out from the collector of
Q9054?
Check for load circuit short-circuiting or leak.
Check the Q9054 periphery circuit.
Does the P-CON switch circuit is operate
normally? (Q9056-7, etc.)
Check each component and if poor the replace.
Are the
"H" pulse inputted into the pin(9) of
IC8201?
Replace IC8201.
Check or replace D9091-5.
NO
NO
NO
YES
YES
YES
YES
YES
NO
PC 5V is not output.
FLOW CHART NO.9
Is -22V voltage supplied at emitter of Q8202?
Check the AT -22V line.
Is voltage of -22V sent out from the collector of
Q8202?
Check for load circuit short-circuiting or leak.
Check the Q8202 periphery circuit.
Are the
"H" pulse inputted into the pin(32) of
IC8201?
Does the P-CON switch circuit is operate normally?
(Q8201, etc.)
Check each component and if poor the replace.
Replace IC8201.
Check or replace D9091-5.
FLOW CHART NO.10
Is 5V voltage supplied at pin(1) of IC9053?
Check the secondary circuit, AT 5V line.
Is voltage of 3.3V sent out from the pin(2) of IC9053?
Check for load circuit short-circuiting or leak.
Check the IC9053 periphery circuit.
Are the
"H" pulse inputted into the pin(9) of IC8201?
Does the P-CON switch circuit is operate normally?
(Q9056-7, etc.)
Check each component and if poor the replace.
Replace IC8201.
Check or replace D9091-5.
NO
NO
NO
NO
NO
NO
YES
YES
YES
YES
YES
YES
YES
YES
NO
YES
YES
NO
PC -22V is not output.
PC 3.3V(1), (2) is not output.
FLOW CHART NO.11
Is 5V voltage supplied at pin(1) of IC9054?
Is voltage of 2.5V sent out from the pin(2) of
IC9054?
Check the secondary circuit, AT 5V line.
Check for load circuit short-circuiting or leak.
Check the IC9054 periphery circuit.
Replace IC9054.
NO
YES
YES
YES
NO
PC 1.8V is not output.(PC 3.3V(1), (2) is possib
le)
57
DV-NC55S/H
DV-NC60H
DV-NC60H
YES
YES
NO
NO
NO
NO
YES
YES
YES
YES
YES
NO
NO
PC 9V is not output.
FLOW CHART NO.6
Check the secondary circuit, AT 12V and PC 12V
switch(Q9053)
circuit.
Is voltage of 9V sent out from the pin(2) of IC9052?
Check for load circuit short-circuiting or leak.
Check the IC9052 periphery circuit.
Are the "H" pulse inputted into the pin(9) of IC8201?
Does the P-CON switch circuit is operate ally?
(Q9056-7, Q9053, etc.)
Check each component and if poor the replace.
Replace IC8201.
Check or replace D9091-5.
FLOW CHART NO.7
Is 12V voltage supplied at pin(1) of IC9052?
Check the PC 12V line.
Is voltage of 8V sent out from the pin(2) of IC9052?
Check for load circuit short-circuiting or leak.
Check the IC9052 periphery circuit.
Replace IC9052.
Is 12V voltage supplied at pin(1) of IC9052?
PC 8V is not output.(PC 9V is possible)
FLOW CHART NO.8
Is 5V voltage supplied at emitter of Q9054?
Check the AT 5V line.
Is voltage of 5V sent out from the collector of
Q9054?
Check for load circuit short-circuiting or leak.
Check the Q9054 periphery circuit.
Does the P-CON switch circuit is operate
normally? (Q9056-7, etc.)
Check each component and if poor the replace.
Are the
"H" pulse inputted into the pin(9) of
IC8201?
Replace IC8201.
Check or replace D9091-5.
NO
NO
NO
YES
YES
YES
YES
YES
NO
PC 5V is not output.
FLOW CHART NO.9
Is -22V voltage supplied at emitter of Q8202?
Check the AT -22V line.
Is voltage of -22V sent out from the collector of
Q8202?
Check for load circuit short-circuiting or leak.
Check the Q8202 periphery circuit.
Are the
"H" pulse inputted into the pin(32) of
IC8201?
Does the P-CON switch circuit is operate normally?
(Q8201, etc.)
Check each component and if poor the replace.
Replace IC8201.
Check or replace D9091-5.
FLOW CHART NO.10
Is 5V voltage supplied at pin(1) of IC9053?
Check the secondary circuit, AT 5V line.
Is voltage of 3.3V sent out from the pin(2) of IC9053?
Check for load circuit short-circuiting or leak.
Check the IC9053 periphery circuit.
Are the
"H" pulse inputted into the pin(9) of IC8201?
Does the P-CON switch circuit is operate normally?
(Q9056-7, etc.)
Check each component and if poor the replace.
Replace IC8201.
Check or replace D9091-5.
NO
NO
NO
NO
NO
NO
YES
YES
YES
YES
YES
YES
YES
YES
NO
YES
YES
NO
PC -22V is not output.
PC 3.3V(1), (2) is not output.
FLOW CHART NO.11
Is 5V voltage supplied at pin(1) of IC9054?
Is voltage of 2.5V sent out from the pin(2) of
IC9054?
Check the secondary circuit, AT 5V line.
Check for load circuit short-circuiting or leak.
Check the IC9054 periphery circuit.
Replace IC9054.
NO
YES
YES
YES
NO
PC 1.8V is not output.(PC 3.3V(1), (2) is possib
le)
