Sharp DV-NC100H (serv.man7) Service Manual ▷ View online
2-4-5
H9740DA
A
(S-2)
[7]
(L-12)
[49]
[50]
Fig. DM6H
View for A
Desolder
from bottom
from bottom
Lead with
Red Stripe
Red Stripe
[8]
[9]
(S-4)
(S-3)
LDG
Belt
Belt
View for A
Desolder
from bottom
from bottom
Lead with White Stripe
A
[8]
Fig. DM7H
[11]
[13]
[12]
[10]
(L-4)
(P-3)
(P-2)
Fig. DM8H-1
Pin of [12]
Pin of [10]
Groove of [27]
View for A
When reassembling [10] and
[12], confirm that pin of [10]
and pin of [12] are in the
groove of [27] as shown.
[12], confirm that pin of [10]
and pin of [12] are in the
groove of [27] as shown.
[27]
Removal of [11]
1) Remove screw
(S-4A).
2) Unhook spring
(P-2).
3)
Release (L-4) while
holding [12] with a
finger.
holding [12] with a
finger.
4)
Loosen a finger
holding [12] and
remove [11].
holding [12] and
remove [11].
A
(S-4A)
2-4-6
H9740DA
Installation of [13] and [12]
Pin of [12]
Groove of [27]
Hook spring (P-3) up to [12]
and [13], then install then to
the specified position so that
[12] will be floated slightly
while holding [12] and [13].
(Refer to Fig. A.)
and [13], then install then to
the specified position so that
[12] will be floated slightly
while holding [12] and [13].
(Refer to Fig. A.)
Fig. A
[13]
[12]
(P-3)
Fig. B (Top view)
Install pin of [12] in groove of [27].
(Refer to Fig. B.)
(Refer to Fig. B.)
[27]
Hold [12] and [13] till groove of
pin of chassis looks and fit [13]
in notch of chassis. Then, turn
a few [13] while holding [12].
(Refer to Fig. C.)
pin of chassis looks and fit [13]
in notch of chassis. Then, turn
a few [13] while holding [12].
(Refer to Fig. C.)
Fig. C
Groove of
pin of chassis
pin of chassis
Notch of
chassis
chassis
turn
[13]
[12]
Install [11] and [10] while holding [12].
(Refer to Fig. DM8H-1.)
(Refer to Fig. DM8H-1.)
Fig. DM8H-2
[14]
[15]
(S-6)
(S-5)
Fig. DM9H
[17]
[16]
(L-5)
[18]
(P-4)
(S-7)
Fig. DM10H
2-4-7
H9740DA
[19]
Cap Belt
(S-8)
[19]
[20]
Cap Belt
A
Installation position of Cap Belt
View for A
Fig. DM11H
(L-6)
[22]
[20]
(C-1)
[21]
[27]
Pin on [22]
Position of p
in on [22]
turn
Fig. DM12H
2-4-8
H9740DA
[27]
[31]
(C-3)
[26]
(C-4)
[25]
(C-2)
[28]
[29]
[30]
(C-5)
(S-9)
[24]
[23]
(L-7)
(L-8)
Fig. DM13H-1
[27]
[27]
[26]
Top View
First tooth on [47]
First groove on [27]
Align [26] and [27] as shown.
Pin of [36]
Pin of [33]
Position of Mode Lever when installed
Pin of [37]
Bottom View
Installation of [26]
When reassembling [27],
meet the first groove on
[27] to the first tooth on
[47] as shown.
meet the first groove on
[27] to the first tooth on
[47] as shown.
Fig. DM13H-2
[32]
(L-9)
(P-5)
[34]
[35]
Refer to the Alignment
Section, Page 2-5-1.
Section, Page 2-5-1.
[33]
Fig. DM14H
Click on the first or last page to see other DV-NC100H (serv.man7) service manuals if exist.